Elmdene VRS124000-P Series User manual

1
Technical Support: [phone] (option 3) PAK200565 01B ©2016 ELMDENE INTERNATIONAL LTD
12vdc 4A IP68
CCTV SMPSU
VRS124000-xP
1 x 4.0A Fused Output
2 x 2.0A Fused Outputs
4 x 1.0A Fused Outputs
8 x 0.5A Fused Outputs
Where ‘x’ is the number of fused outputs 1, 2, 4 or 8 (model dependent)
-IP68 enclosure
-Universal mains input voltage 90-264vac
-High efficiency electronics for reduced
running costs and lower operating
temperatures
-Continuous full rated current to load
-Installer safe design with all high voltage
electronics fully shrouded
-Modular construction for ease of
maintenance & installation
-Available in 1, 2, 4, or 8 channel versions
(model dependent)
-Individually Fused Outputs
-Individual channel LED health indication
-Full electronic short circuit and overload
protection on load output
-Mains transient protection circuit
-Green ‘Mains Present’ LED
-Red ‘Fault’ LED
F ATUR S
The VRS124000-xP IP68 range consists of high efficiency cost effective power supplies, ideal for use in
CCTV applications. They feature regulated 12.0vdc SMPS modules, continuously supplying full rated
current to load, while their universal mains input voltage enables the power supply to be used across a
wide geographical area. The highly efficient switch mode design generates less heat and ensures low
operating costs. The modular construction simplifies maintenance and the fused output module allows
multiple circuits to be individually protected.
O P RATION
This unit is intended for use by Service Personnel only - There are NO USER SERVICEABLE parts inside.
The green Mains LED will be illuminated whilst the mains supply is present. In the event of a fault
condition, the red Fault LED will also be illuminated on the module.
I NSTALLATION AND S T -U P
This unit is only suitable for installation as permanently connected equipment. The PSU is suitable for
external installation. EQUIPMENT MUST BE EARTHED. Before installation, ensure that external
disconnect device is OFF. The PSU should be installed according to all relevant safety regulations
applicable to the application.
Elmdene International Ltd Tel: [phone]
3 Keel Close, Interchange Park, Fax: [phone]
Portsmouth, Hampshire, PO3 5QD, UK  Web: www.elmdene.co.uk

2
Technical Support: [phone] (option 3) PAK200565 01B ©2016 ELMDENE INTERNATIONAL LTD
Mounting
1. The four enclosure mounting screw locations are found within the four lid screw holes.
2. To ensure the IP68 rating is kept - cable glands used for cable entry must be of IP68 rating.
3. Route mains and low voltage output cables via different cable entries.
4. Use bushes and cable glands rated to UL94 HB minimum.
Mains Power Up
1. Attach correctly rated mains cable (minimum 0.5mm
2
[3A], 300/500Vac).
2. Apply mains power. Check for 12.0Vdc on load outputs. Check green Mains LED is illuminated on
the modules.
3. Disconnect mains power.
Load Output
1. Attach correctly rated load cable(s). Note polarity.
2. Re-apply mains power. Check green Mains LED is on.
3. Verify load is operating correctly.
M AINT NANC
There is no regular maintenance required of this PSU.
If the output of the PSU fails the cause of the failure should be investigated e.g. short circuit load. The
fault should be rectified before restoring power to the PSU. The fuse(s) may need to be replaced.
Ensure the correct fuse rating and type is used.
D ISPOSAL OF P RODUCT AT ND OF L IF
This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic
Equipment (WEEE). At the end of life, the product must be separated from the domestic waste stream
and disposed via an appropriate approved WEEE disposal route in accordance with all national and local
regulations.
For more information see: www.rec clethis.info

3
Technical Support: [phone] (option 3) PAK200565 01B ©2016 ELMDENE INTERNATIONAL LTD
S P CIFICATION
Input Specification
VRS124000
-
x
P
Voltage (rated)
100
-
240Vac
Voltage (operating)
90
-
264Vac
Frequency
50
-
60Hz
Mains Input Fuse
(Terminal)
T
2
.
0
A HRC
Module fuse
-
Mains
T2.0A HRC
Max standby Power
0.5W (n
o load connected)
Max Mains Input Current
1.5
A
Output Specification
Voltage
11.
4
–
12.
6
vdc (12.0vdc nominal)
Max load current
4A
Ripple
150 mV pk
-
pk max
Module Output Fuse
F4.0A
Load output Fuse
s
See Model Specification Table below
Overload
Electronic shutdown until overload or short
circuit removed
Local Indicators
MAINS LED (Green)
Mains present
FAULT LED (Red)
Fault present: Output fuse fail
(requires load to be connected)
Fused Outputs
Model: VRS124000-xP
No. of Fused outputs: 1, 2, 4 & 8
Fuse Value:
[as fitted in fused output module(s)]
1 x F4.0A
2 x F2.0A
4 x F1.0A
8 x F500mA
Mechanical
IP68 - Enclosure
Enclosure Dimensions
h x w x d (mm) [external] 250 x 150 x 100
Weight 1.05kg
nvironmental
Temperature
-
10 to +40°C (operating) 95% RH non
-
condensing
-20 to +80°C (storage)

4
Technical Support: [phone] (option 3) PAK200565 01B ©2016 ELMDENE INTERNATIONAL LTD
C OMPLIANC
This product meets the essential requirements of the following EU Directives:
Low Voltage: 2014/35/EU
EMC: 2014/30/EU
RoHS2: 2011/65/EU
WEEE: 2012/19/EU
The packaging supplied with this product ma be rec cled.
Please dispose of packaging accordingl .