Emerson Bettis Om3-SCE300 User manual

Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
May 2022
Bettis OM3 - SCE300
Local Interface Module

May 2022
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
Notes
This page intentionally left blank

i
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
Table of Contents
May 2022
Table of Contents
Table of Contents
Section 1: Optional Module 3: Local Interface Module
1.1 Local Interface Functionality ......................................................................... 1
1.2 Manufacturer................................................................................................ 2
Section 2: Assembling Procedure
Assembling Procedure ............................................................................................ 3
Section 3: Description Of OM3 Local Interface
3.1 Local Operator Interface................................................................................ 7
3.2 Description of the Local Interface.................................................................. 8
3.2.1 2-position selector ............................................................................. 8
3.2.2 LEDs indicating the position of the SCE300 actuator........................... 8
3.2.3 OPEN/CLOSE pushbuttons.................................................................. 8
Section 4: To Locally Operate the Actuator
To Locally Operate the Actuator .............................................................................. 9
Section 5: OM3 Wiring Diagram
OM3 Wiring Diagram............................................................................................ 10
Section 6: Identication
6.1 Water-, Dust-Proof Version.......................................................................... 11
6.2 Label for Application In Water-, Dust-Proof Areas............................................ 11
6.3 Explosion-Proof Version .............................................................................. 12
6.4 ATEX Label for Application in Hazardous Areas ............................................ 12
Section 7: Safety Instructions
7.1 Foreword .................................................................................................... 13
7.2 General Safety Instructions ......................................................................... 13
7.3 Check for Right Application......................................................................... 13
7.4 Applicable Standards and Regulations......................................................... 14
7.5 Terms and Conditions ................................................................................. 14
7.6 Manufacturer’s Liability............................................................................... 14
Section 8: Installation
8.1 Working Conditions .................................................................................... 15
8.2 Electrical Connections................................................................................. 15
8.3 Instructions for the Intrinsically-Safe Enclosures.......................................... 15
8.4 Installation in Ambient with Explosive Dusts................................................ 15
Section 9: Special Maintenance
9.1 Periodic Inspections .................................................................................... 16
9.2 Repairs of Intrinsically-Safe Parts ................................................................. 16

May 2022
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
Notes
This page intentionally left blank

Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0 May 2022
1
Optional Module 3: Local Interface Module
Section 1: Optional Module 3: Local Interface Module
Section 1: Optional Module 3: Local
Interface Module
1.1 Local Interface Functionality
The OM3 Local Interface module is supplied as an option on Bettis SCE300 actuators and
ts all models. It is possible to receive the actuator already equipped with the OM3 if
ordered together with the basic version. Alternatively, only for the water proof version,
it is possible to order the OM3 as a separate kit to be installed afterwards on the basic
actuator. The subsequent retrotting of the OM3 on existing SCE300 is not allowed in the
explosion-proof version. The OM3 is an optional module allowing local control with the
following additional functionalities:
• Selection of Local/Remote actuator control through the selector (lockable in
both positions).
• Open/Close command through the non intrusive pushbuttons.
• Actuator position indication by means of 2 LEDs.
NOTE:
For decommissioning instructions, please refer to the relevant section in
Installation, Operation and Maintenance Manual for Bettis SCE300 electric actuator.
!WARNING
SCE300 actuator must be electrically isolated before any disassembling and reassembling
operations. Before any disassembling or reassembling operations, please follow in detail the
relevant paragraph of the basic installation and operating manual (latest revision available).
!WARNING
The electronic parts of the SCE300 actuators and all optional modules can be damaged
by a discharge of static electricity. Before you start, touch a grounded metal surface to
discharge any static electricity.
NOTE:
The present IOM has to be considered integral part of the IOM for the basic
Installation, Operation and Maintenance Manual for Bettis SCE300 electric actuator.

May 2022
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
2Optional Module 3: Local Interface Module
Section 1: Optional Module 3: Local Interface Module
!WARNING
SCE300 actuators can be operated through a Bluetooth™ PDA or PC with the
following conguration:
• The commands are enabled by Bluetooth, only when the BT control is active. When
operating with Bluetooth™, the controls via PDA or PC have priority on any other
remote commands and allow full actuator operability from a distance also when
the valve is not visible. Special attention must be paid under this condition to avoid
any damages or injuries to people working close to the valve. Bettis will not
accept any responsibility for damages or injuries caused by an improper use of your
Bluetooth™ PDA or PC.
!WARNING
It is assumed that the installation, conguration, commissioning, maintenance and repair
works are carried out by qualied personnel and checked by responsible specialists.
!WARNING
Repair work, other than operations outlined in this manual, is strictly reserved to qualied
Emerson personnel or to personnel authorized by the company itself.
1.2 Manufacturer
Manufacturer with respect to Machinery Directive 2006/42/EC: Emerson as specied on
the actuator label.

Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0 May 2022
3
Assembling Procedure
Section 2: Assembling Procedure
Section 2: Assembling Procedure
To assemble the OM3 Local Interface module onto the SCE300 actuator, proceed as follows:
• Ensure that all the parts received with the OM3 are available, see Figure 1:
Figure 1 OM3 kit for SCE300 actuator
Pos. Q.ty Description
1 1 Local Interface module
2 4 Screws for connecting connector
Table 1.
• Gather the right tools for the assembly: a 5 mm Allen key and a screwdriver as
shown in Figure 2.
Figure 2 Tools for installing OM3 kit
1
2

May 2022
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
4Assembling Procedure
Section 2: Assembling Procedure
• With the Allen key loosen the 4 cover screws and remove the terminal board
enclosure cover, see Figures 3. You will see the terminal board inside the actuator.
Remove the ground cable from the cover in the enclosure. The position of the
connections is shown on the yellow label that you will nd inside the cover just
removed, see Figure 4.
Figure 3 Removing terminal board enclosure cover
Figure 4 Electrical connections
!WARNING
Pay attention not to damage the joint surfaces of the cover/enclosurer.

Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0 May 2022
5
Assembling Procedure
Section 2: Assembling Procedure
• Connect the Local Interface module to the ground stud by screwing the
‘ground kit’ (screw + toothed washer).
Figure 5 Grounding the Local Interface
• Take the 4 screws for connecting the Local Interface black connector to the
terminal board, in pos. 28-29-30-31 (see Figure 6 and wiring diagram) and
connect it with the screwdriver shown in Figure 7.
Figure 6 Position of the Local Interface connector on the terminal board
Figure 7 Connecting the Local Interface connector

May 2022
Installation, Operation and Maintenance Manual
VCIOM-17109-EN Rev. 0
6Assembling Procedure
Section 2: Assembling Procedure
• Now the Local Interface is connected to the actuator, see Figure 8.
• Take the 4 screws removed from terminal board cover and use them to x the Local
Interface to the actuator, using the 5 mm Allen key, see Figure 9.
Figure 8 OM3 kit connected to the SCE300 terminal board
Figure 9 Fixing the local interface onto the SCE300 actuator
NOTE:
Please note that the design of the Local Interface black connector has been engineered to
allow the installation in one way only. Due to the special design, it is not possible to reverse
the connection of the 4 cables to the terminal board and it is not possible to make a wrong
connection of the connector.
• The installation of the OM3 Local Interface module onto the SCE300 actuator is
now complete.
screws