Emerson PACSystems RX3i IC695CPE330 User manual

PACSystems™ RX3i64MB CPU
w/EthernetIC695CPE330QuickStart
Guide
GFK-2941K
Sept2019

i PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Contents
User Features................................................................ 3
Switches ..................................................................... 5
Light-EmittingDiode Indicators (LEDs)...................................... 7
Status Indicators ..................................................................................................7
Ethernet Ports ....................................................................................................10
Hardware Installation...................................................... 12
Initial Checks ......................................................................................................12
Installation Location...........................................................................................12
Installation in Hazardous Areas ..........................................................................13
Class 1 Division 2 Groups ABCD .........................................................................13
ATEX Zone 2.......................................................................................................14
Grounding..........................................................................................................14
Module Start-up ........................................................... 15
You Will Need: ...................................................................................................15
Basic Installation Steps.......................................................................................16

ii PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Redundancy Configuration ................................................................................17
PROFINET Controller Configuration ...................................................................18
Backward Compatibility with CPU320/CRU320/CPU315 ..................................18
Removable Data Storage Device (RDSD) ...........................................................21
Periodic Maintenance ..................................................... 21
Real-Time Clock Battery.....................................................................................21
Spare Parts .........................................................................................................23
Additional Information .................................................... 23

3 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
User Features
The PACSystems™RX3i CPE330 is a richly featured programmable
controller CPU equipped with 64 Mbytes of built-in program memory and
two independent high-speedEthernet interfaces. It isideallysuited for
multi-tier communications andfor synchronizinglarge amounts of data.
Itsmetal housing provides superior noise immunity.
The CPE330 is programmed andconfigured over Ethernet via PAC
Machine Edition™(PME) software. It resides in the RX3i main rack and
supports all RX3i I/O and Intelligent Option modules, up to 32K I/O
points.
▪Supports an updated OPC stack and certificate management
▪Supports PME’s new GUI management interface for OPC UA configuration
integration (start, stop, restart, clear, and provisioning mode)
▪Supports the new PAC Security tool available for certificate trust
management for clients and servers
▪Supports RX3i Hot Standby Redundancy CPU with PROFINET®I/O using
embedded PROFINET or using rack-mounted IC695PNC001 PROFINET
Controllers.
▪Supports RX3i Hot Standby Redundancy with Ethernet (EGD) & Genius I/O.
▪Enabled simplex PROFINET I/O controller with support for up to 32 I/O
devices and update rates of 1 –512 ms. I/O device update rates of 8 ms

4 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
and faster are possible with 16 or fewer devices. When there are more than
16 devices configured, update rates of 16 ms and higher are available.
▪Supports the Remote Get HART®Device Information COMMREQ, which
allows the user application to read information from a HART device
connected to an RX3i Analog module in an IC695PNS001 RX3i PROFINET
Scanner. A UDFB that automates the COMMREQ control logic is available for
download. (Refer to New Features and Enhancements for additional
information.)
▪Configured with Sequence of Events recording through the Embedded
PROFINET Controller when used with up to four IC695PNS101 Advanced
PROFINET Scanner modules. A RX3i SoE system supports events from up to
512 SoE input points with a system storage buffer for up to 128,000 events at
a maximum rate of 400 events per second per PNS101. Each PNS101
supports SoE recording with IRIG B time synchronization of events accurate
to 1ms and buffers up to 4000 events from up to four IC694MDL660
32 Circuit Discrete Input modules. Unmodulated IRIG B time signals are
decoded by the PNS101 using either an IC695HSC304 or IC695HSC308 High
Speed Counter Module. SoE recording is available in both simplex and
redundant PROFINET systems.
▪Supports programming in Ladder Diagram, Structured Text, Function Block
Diagram, or C.
▪Contains 64 Mbytes of configurable data and program memory.
▪Supports auto-located Symbolic Variables that can use any amount of user
memory.

5 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
▪Contains reference tables include 32k bits for discrete %I and %Q and up to
32k words each for analog %AI and %AQ. Bulk memory (%W) also supported
for data exchanges.
▪Supports up to 768 program blocks. Maximum size for a block is 128KB.
▪Configured to display serial number and date code in PME Device Information
Details.
▪Configured for Coordinated Universal Time (UTC) and Day Light Savings Time
(DST) support.
▪Operating temperature range 0 C to 60 C (32 F to 140 F).
▪Compliant with EU RoHS Directive 2002/95/EC using the following
exemptions identified in the Annex: 7(a), 7(c)-I and III, and 15.
Switches
The Run/Stop switch andRDSD UPLD andRDSD DNLD pushbuttons are
located behind the protectivefront door. Switch operationis given in the
followingtable.
The Run/Stop switch is enabled by default; it can be disabled in the PME
Hardware Configuration (HWC) settings. The memory protection function
of this switch can be disabled separately in HWC. The memory protection
functionality is disabled by default.

6 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
RDSD
Pushbuttons
Function
RDSD UPLD
Loads user program or data fromCPU to RDSD.
RDSD DNLD
Stores user program or data fromRDSDto CPU.
Run/Stop
Swi tch Position
A three-positionswitch which operates as follows:
CPU and Sweep Mode
Mem ory Protection
Run I/O
The CPU runswith I/O
sweep enabled.
User program memory is read
only.
Run
The CPU runs with
outputs disabled.
User program memory is read
only.
Stop
The CPU isnot allowed
to go into Run mode.
User program memory can be
written.

7 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Light-EmittingDiode Indicators(LEDs)
Status Indicators
LED
LED State
OperatingState
CPU OK
On
Green
CPU has passed itspower-updiagnosticsand
is functioningproperly. (After initialization
sequence is complete.)
Off
Power isnot applied, or CPU has a problem,
which may be indicated by blink pattern.
Blinking
Other
LEDsoff
CPU in Stop-Halt state; possible watchdog
timer fault. If the programmercannot
connect, cycle power with charged Energy
Pack attached and refer to fault tables.
CPU OK
On
Amber
CPU indicating CPU320/CRU320
compatibility setting
FORCE
On
Amber
Refer to the section, Compatibility with
CPU320/CRU320/CPU315for more
information.
RUN
Blinking
in
unison
CPU is updatingan internal programmable
hardware device.
OUT EN

8 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
LED
LED State
OperatingState
RUN
On
Green
CPU isin Run mode.
Off
CPU isin Stop mode.
OUT EN
On
Green
Output scan is enabled.
Off
Output scan is disabled.
FORCE
On
Amber
Override is active on abit reference.
Off
No Overridesactive in I/OReference Tables.
RDSD
On
Green
USB Device detected (No Activity)
Blinking
Green
Port activity detected on USB Interface
Off
No port activity detected on USB Interface
On Red
RDSD Failure
Blinking
Red
Target name mismatch: Presssame RDSD
pushbutton again to dismiss.
SYS FLT
On Red
CPU isin Stop/Faulted mode: a fatal fault has
occurred.
Off
No fatal faults detected.

9 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
CPE330 Ethernet Indicators
LED
LED State
OperatingState
LINK
(upper)
On
Green
The corresponding link isphysically
connected.
Blinking
Green
Traffic isdetected at the corresponding port.
Off
No connection detected at corresponding
port.
1Gbps
(lower)
On
Amber
(LAN1)
or
Corresponding networkdata speed is 1
Gbps.
On
Green
(LAN2)
Off
Corresponding network dataspeedis 100
Mbps or 10 Mbps.

10 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Ethernet Ports
LAN1 connects to the uppermost RJ-45 connector. It isnot switched. LAN2
connects to the two lower RJ-45 connectors. They areswitched internally.
Record the IP Address of each LAN inthe space provided (Figure 1).
Each of the embedded Ethernetinterfacesautomatically sensesthe data
rate (10 Mbps or 100 Mbps or 1 Gbps), communications mode (half-duplex
or full-duplex), andcabling arrangement (straight-through or crossover) of
the attachedlink.
For improved performance,the twoEthernet LANsare serviced by a
dedicated microprocessor core.In addition, each Ethernet LANisserviced
by a dedicated Network InterfaceController (NIC). In thisway, theservicing
of the Ethernet ports isindependentof the controller logic andI/O
scanning. This superior level of servicingis required at the higher
communications rates.
Anyof the embeddedEthernet portsmay be used tocommunicate with the
PME programmingsoftware usingthe ServiceRequestTransportProtocol
(SRTP, a proprietary Emerson protocol, used primarily for communication
with the programmer).
To establish Ethernet communications between PME and the CPE, Emerson
recommends inserting an ETM with a known IP address into the rack to
store ahardware configurationfor theCPE330 with the desired IP address.

11 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
CPE330 LAN1
CPE330 LAN2
IP Address:
192.168.0.100
10.10.0.100
Subnet
Mas k:
255.255.255.0
255.255.255.0
Gateway:
0.0.0.0
0.0.0.0
Figure 1: TypicalMulti-Tier LAN Application
A typical application will take advantage of the two independent LANs. The
dedicated LAN1 port will be used for communicationswith plant-level or
supervisory layers. The switched LAN2 will typically be used to
communicate with devices within themanufacturing cell or process,
including local HMI devices and micro-controllers.

12 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Hardware Installation
Initial Checks
Upon receivingyour RX3i equipment, carefully inspect all shipping
containers for damage. If any part of the system is damaged, notify the
carrier immediately.The damaged shipping container shouldbe saved as
evidence for inspection by the carrier.
Asthe consignee, it isyour responsibility to register aclaim with the carrier
for damage incurred during shipment. Emerson Automation Solutions will
fully cooperate with you, however, should such action be necessary.
After unpackingthe RX3i equipment, recordall serial numbers.Serial
numbersare required if you shouldneed to contact Customer Care during
the warranty period. All shipping containers andall packingmaterial should
be saved should it be necessary to transport or shipany part of the system.
Verify that all components of the system have been received andthat they
agree with your order. If the system received does not agreewith your
order, contact Customer Care.
Installation Location
Thisproduct isintended for use with the RX3i system. Itscomponents are
considered open equipment (havinglive electrical parts that may be

13 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
accessible to users)and must be installed in anultimate enclosure that is
manufactured to provide safety. At a minimum, the enclosure shall provide
a degree of protection against solidobjects as small as 12mm (e.g. fingers).
This equates to aNEMA/UL Type 1 enclosureor an IEC60529 IP20 rating
providingat least a pollutiondegree 2 environment. For detailsabout
installingRX3i racksystems, refer to the PACSystems RX3i System Manual,
GFK-2314.
If you need technical help, contact Technical Support.For phone numbers
and email addresses, refer to the back cover of thisGuide.
Installation in Hazardous Areas
The followinginformationis for products bearingthe ULmarkingfor
Hazardous Areasor ATEX marking for explosive atmospheres:
Class 1 Division 2 Groups ABCD
▪Thisequipment isan open-type device andis meant to be installed in
an enclosure suitable for the environmentthat isonly accessible with
the use ofa tool.
▪Suitable for use in ClassI, Division2, GroupsA, B, C and D Hazardous
Locations, or nonhazardouslocations only.

14 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
•WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
•WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS AREAS, TURN
OFF POWER BEFORE REPLACING OR WIRING MODULES.
ATEX Zone 2
This module must be mounted in an enclosure certified in accordance with
EN60079-15 for use in Zone 2, Group IIC and rated IP54. The enclosure shall
only be able to be openedwith the use of atool.
Grounding
The RX3i rackinto which thisproduct will be mounted must be grounded
per the instructions provided in PACSystems RX3i System Manual, GFK-2314.
Also, if an Energy Pack (IC695ACC402) is connected, its ground-strap must
be groundedasdescribed in PACSystems RX3i Energy Pack IC695ACC402
Quick Start Guide, GFK-2939.

15 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
ModuleStart-up
You Will Need:
▪An RX3i Universal Backplane: IC695CHS007, IC695CHS012 or
IC695CHS016.
▪This PACSystems RX3i CPU. This CPU occupies two backplane slots.
▪An RX3i rack-mounted Power Supply Moduleand compatible power
source
(AC
1
or DC).
▪A computer running PAC Machine Edition (PME) configuration and
programmingsoftware. PME Version 9.70SIM 16 or later supportsall
features in this document.
▪Ethernet cable for connectingthe PMEprogrammercomputer tothe
RX3i CPU.
▪Phillip’s head screwdriver.
▪A very small slotted screwdriver (1.4 mm jeweler’s size).
1
On lightly-loaded racks, use IC695PSA040H or later, or IC695PSA140D or later, otherwise power-
up may be unsuccessful. Alternately, fill out the empty slots in the rack to draw more current.

16 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
Basic Installation Steps
For startup and configuration of the CPE330, complete thefollowing steps.
For full details on CPE330 operation, refer to the PACSystems RX3i &RSTi-EP
CPU Reference Manual, GFK-2222 or later.
1. Turn power off at the RX3i rackand install the CPE330 in adouble-
slot which is CPU-compatible (refer to PACSystems RX3i System
Manual, GFK-2314 Chapter 3). Typically, theCPUis in the left-most
slot pair, or in the pair of slots to the right ofthe power supply
module.
2. If used, mount the compatible RX3i Energy Pack (IC695ACC402)
within 3 feet of the CPU. The dedicated interconnect cable attaches
to the underside of CPE330. Follow interconnect and grounding
instructions in PACSystems RX3i EnergyPackIC695ACC402Quick Start
Guide, GFK-2939. Securethe two retention flat-head screws with a
very small slotted screwdriver.
3. Set the pair of hooktabsat toprear of the CPU module into two
adjacent notches on the alignment rail of the RX3i rack backplane.
Thisaligns the module with the intended slotsin the main rack and
with the right-side connector of this pair.
4. Swing the module down until the rear connector on theCPU module
engages the mating backplane connector. Firmly engagethe
connectors.
5. Visually inspect the module to be sure it is properly seated.

17 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
6. Usinga Phillip’s head screwdriver,secure thetwo captiveM3x 5 mm
machine screws into the matchingthreaded holes in the backplate
of the RX3i I/O rack. The two screws are locatedat the bottomrear
of the CPU module. Tighten.
7. Apply power to the rack.
Note: When the ACC402 Energy Packis powered up, a period of time is
required to charge it up to its operating level. During this time, the
Energy Pack will indicate thiscondition viaits LEDs (refer to
PACSystems RX3i Energy Pack IC695ACC402 Quick StartGuide, GFK-
2939).
The CPE330 will begin itsboot cycle once ACC402 ischarged. This
typically takes 90 seconds or less. In the event the ACC402 is faulty or
is not communicating, CPE330 commences operation without the
Energy Pack.
Redundancy Configuration
PAC Machine Edition 8.60 SIM 8 or later may be used to createnative
CPE330 redundant applications when a rack-mounted IC695PNC001 is used
as the PROFINET Controller. If usingthe CPE330 EmbeddedPROFINET
Controller, use PME9.50 SIM 7 or later.

18 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
To enable redundancy in a CPE330 project, select theCPE330 target in the
PME Navigator and use the Property Inspector to change theEnable
Redundancy target property to True.
PROFINET Controller Configuration
PAC Machine Edition 8.60 SIM 13, PME 9.00 SIM 4 or later may be used to
configure an Embedded PROFINET Controller in the CPE330 Hardware
Configuration on LAN 2.
To enable the PROFINET ControllerinaCPE330 project, select theCPE330
2
target in the PME Navigator and open the HardwareConfiguration. On the
Settings tab, change the LAN 2 Mode to PROFINET. ThePROFINETController
node description now displaysthat it isusing LAN 2 asa submodule under
the CPE330.
Compatibility with CPU320/CRU320/CPU315
The CPE330 also servesasa drop-in replacement for the CPU320, CRU320,
and CPU315 Controllers without theneed to upgradePME. To download
projects intended for the CPU320/CRU320 to a CPE330 with versions of
PME that do not support the CPE330, you must change the CPE330’s
compatibility setting.
2
CPE330 release 8.90 or later is required for the embedded PNC feature.

19 PACSystems™ RX3i 64 MB CPU w/Ethernet Quick Start Guide GFK-2941K
To change the compatibility setting, performthe following operations:
1. Power off the CPE330 and remove any USB stick that might be attached to
its USB connector.
2. Place the CPE330’s RUN/STOP switch in the STOP position.
3. Hold down the RDSD UPLD button and turn power on to the CPE330.
Continue to depress the RDSD UPLD button until the CPE330 powers up
and displays one of the following patterns on the LEDs.
CPU StatusIndicators
On
Blinking
Off
CPE330 LED
LED State
Ope rating State
CPU OK
On Amber
Normal mode. (Compatible with CPU320)
FORC E
On Amber
RUN
Off
RD S D
On Red
OUT EN
Off
SYS FLT
On Red
CPU OK
On Amber
CRU320 Compatibility mode.
FORC E
On Amber
RUN
On Red
RD S D
Off
OUT EN
Off
SYS FLT
On Red