Endress+Hauser Proline 500 Technical specifications

Products Solutions Services
Brief Operating Instructions
Proline 500
Transmitter with ultrasonic time-of-flight sensor
Modbus RS485
These instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Brief Operating Instructions part 2 of 2: Transmitter
Contain information about the transmitter.
Brief Operating Instructions part 1 of 2: Sensor →  3
KA01476D/06/EN/01.21
71508894
2021-05-10

Proline 500 Modbus RS485
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555

Proline 500 Modbus RS485 Brief Operating Instructions for flowmeter
Endress+Hauser 3
Brief Operating Instructions for flowmeter
The device consists of a transmitter and a sensor.
The process of commissioning these two components is described in two separate manuals
that together form the Brief Operating Instructions for the flowmeter:
• Brief Operating Instructions Part 1: Sensor
• Brief Operating Instructions Part 2: Transmitter
Please refer to both parts of the Brief Operating Instructions when commissioning the device,
as the contents of the manuals complement one another:
Brief Operating Instructions Part 1: Sensor
The Sensor Brief Operating Instructions are aimed at specialists with responsibility for
installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation
Brief Operating Instructions Part 2: Transmitter
The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for
commissioning, configuring and parameterizing the measuring device (until the first
measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information
Additional device documentation
These Brief Operating Instructions are Brief Operating Instructions Part 2:
Transmitter.
The "Brief Operating Instructions Part 1: Sensor" are available via:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App
Detailed information about the device can be found in the Operating Instructions and the
other documentation:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App

Table of contents Proline 500 Modbus RS485
4 Endress+Hauser
Table of contents
1 About this document .............................................................. 5
1.1 Symbols used ......................................................................... 5
2 Safety instructions ................................................................ 7
2.1 Requirements for the personnel ............................................................ 7
2.2 Designated use ........................................................................ 7
2.3 Workplace safety ...................................................................... 8
2.4 Operational safety ......................................................................8
2.5 Product safety ......................................................................... 8
2.6 IT security ............................................................................ 8
2.7 Device-specific IT security ................................................................ 8
3 Product description .............................................................. 10
4 Installation ...................................................................... 10
4.1 Mounting the transmitter housing ......................................................... 10
4.2 Turning the transmitter housing .......................................................... 13
4.3 Turning the display module .............................................................. 15
4.4 Cover locking ........................................................................ 16
4.5 Transmitter post-installation check ........................................................ 17
5 Electrical connection ............................................................ 18
5.1 Electrical safety .......................................................................18
5.2 Connection conditions .................................................................. 18
5.3 Connecting the measuring device ......................................................... 22
5.4 Ensuring potential equalization ........................................................... 29
5.5 Hardware settings ..................................................................... 30
5.6 Ensuring the degree of protection ......................................................... 31
5.7 Post-connection check ..................................................................32
6 Operation options ............................................................... 33
6.1 Overview of operation options ............................................................ 33
6.2 Structure and function of the operating menu ................................................ 34
6.3 Access to the operating menu via the local display ............................................. 35
6.4 Access to the operating menu via the operating tool ............................................ 38
6.5 Access to the operating menu via the Web server .............................................. 38
7 System integration .............................................................. 38
8 Commissioning .................................................................. 39
8.1 Function check ....................................................................... 39
8.2 Setting the operating language ........................................................... 39
8.3 Configuring the measuring device ......................................................... 40
8.4 Protecting settings from unauthorized access ................................................. 40
9 Diagnostic information .......................................................... 41

Proline 500 Modbus RS485 About this document
Endress+Hauser 5
1 About this document
1.1 Symbols used
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Symbols for certain types of information
Symbol Meaning Symbol Meaning
Permitted
Procedures, processes or actions that
are permitted.
Preferred
Procedures, processes or actions that
are preferred.
Forbidden
Procedures, processes or actions that
are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
1.
,
2.
,
3.
… Series of steps
Result of a step Visual inspection
1.1.3 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.

About this document Proline 500 Modbus RS485
6 Endress+Hauser
Symbol Meaning
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
1.1.4 Communication symbols
Symbol Meaning Symbol Meaning
Wireless Local Area Network
(WLAN)
Communication via a wireless, local
network.
Bluetooth
Wireless data transmission between
devices over a short distance.
Promag 800
Cellular radio
Bidirectional data exchange via cellular
network.
LED
Light emitting diode is off.
LED
Light emitting diode is on.
LED
Light emitting diode is flashing.
1.1.5 Tool symbols
Symbol Meaning Symbol Meaning
Torx screwdriver Flat blade screwdriver
Cross-head screwdriver Allen key
Open-ended wrench
1.1.6 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction

Proline 500 Modbus RS485 Safety instructions
Endress+Hauser 7
2 Safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣Follow instructions and comply with basic conditions.
2.2 Designated use
Application and media
The measuring device described in this manual is intended only for the flow measurement of
liquids.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or where there is an
increased risk due to process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.
Residual risks
LWARNING
The electronics and the medium may cause the surfaces to heat up or freeze. This
presents a burn hazard!
‣For elevated or low fluid temperatures, ensure protection against contact.

Safety instructions Proline 500 Modbus RS485
8 Endress+Hauser
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
If mounting the sensors and tensioning bands:
‣Due to the increased risk of cuts, gloves and goggles must be worn.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣Due to the increased risk of electric shock, gloves must be worn.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.
2.7 Device-specific IT security
The device offers a range of specific functions to support protective measures on the operator's
side. These functions can be configured by the user and guarantee greater in-operation safety
if used correctly.
For detailed information on device-specific IT security, see the Operating Instructions for
the device.

Proline 500 Modbus RS485 Safety instructions
Endress+Hauser 9
2.7.1 Access via service interface (CDI-RJ45)
The device can be connected to a network via the service interface (CDI-RJ45). Device-specific
functions guarantee the secure operation of the device in a network.
The use of relevant industrial standards and guidelines that have been defined by national
and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended.
This includes organizational security measures such as the assignment of access authorization
as well as technical measures such as network segmentation.
Transmitters with an Ex de approval may not be connected via the service interface (CDI-
RJ45)!
Order code for "Approval transmitter + sensor", options (Ex de): BB, C2, GB, MB, NB

Product description Proline 500 Modbus RS485
10 Endress+Hauser
3 Product description
The measuring system consists of a transmitter and two or one sensor sets.
The transmitter and sensor are mounted in physically separate locations. They are
interconnected via sensor cable(s).
1
2
2
A0041373
1 Transmitter with integrated ISEM
2 Sensor cable
For detailed information on the product description, see the Operating Instructions for
the device
4 Installation
For detailed information about mounting the sensor, see the Sensor Brief Operating
Instructions →  3
4.1 Mounting the transmitter housing
LCAUTION
Ambient temperature too high!
Danger of electronics overheating and housing deformation.
‣Do not exceed the permitted maximum ambient temperature .
‣If operating outdoors: Avoid direct sunlight and exposure to weathering, particularly in
warm climatic regions.
LCAUTION
Excessive force can damage the housing!
‣Avoid excessive mechanical stress.
The transmitter can be mounted in the following ways:
• Post mounting
• Wall mounting

Proline 500 Modbus RS485 Installation
Endress+Hauser 11
4.1.1 Wall mounting
20 (0.79)
100 (3.94)
100 (3.94)
! 8.6 (0.39)
! 18 (0.71)
! 10 (0.39)
A0029068
 1 Engineering unit mm (in)

Installation Proline 500 Modbus RS485
12 Endress+Hauser
4.1.2 Post mounting
LWARNING
Order code for "Transmitter housing", option L "Cast, stainless": cast transmitters are
very heavy.
They are unstable if they are not mounted on a secure, fixed post.
‣Only mount the transmitter on a secure, fixed post on a stable surface.
1
4 x SW 13
! … (! 0.79 to 2.75)20 70
A0029057
 2 Engineering unit mm (in)

Proline 500 Modbus RS485 Installation
Endress+Hauser 13
4.2 Turning the transmitter housing
To provide easier access to the connection compartment or display module, the transmitter
housing can be turned.
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
+E
ESC
–
1.
2.
3 mm
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
+E
ESC
–
3.
4 mm
4.
7 Nm (5.2 lbf ft)
A0029993
 3 Non Ex housing
1. Depending on the device version: Loosen the securing clamp of the connection
compartment cover.
2. Unscrew the connection compartment cover.
3. Release the fixing screw.
4. Turn the housing to the desired position.
5. Tighten the fixing screw.
6. Screw on the connection compartment cover.
7. Depending on the device version: Attach the securing clamp of the connection
compartment cover.

Installation Proline 500 Modbus RS485
14 Endress+Hauser
1.
2.
3.
4 mm 7 Nm (5.2 lbf !)
A
A
A0043150
 4 Ex housing
1. Loosen the securing screws.
2. Turn the housing to the desired position.
3. Tighten the securing screws.

Proline 500 Modbus RS485 Installation
Endress+Hauser 15
4.3 Turning the display module
The display module can be turned to optimize display readability and operability.
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
+E
ESC
–
1.
2.
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
+E
ESC
–
3.
3 mm
+E
ESC
–
A0030035
1. Depending on the device version: Loosen the securing clamp of the connection
compartment cover.
2. Unscrew the connection compartment cover.
3. Turn the display module to the desired position: max. 8 × 45° in each direction.
4. Screw on the connection compartment cover.
5. Depending on the device version: Attach the securing clamp of the connection
compartment cover.

Installation Proline 500 Modbus RS485
16 Endress+Hauser
4.4 Cover locking
NOTICE
Order code for "Transmitter housing", option L "Cast, stainless": The covers of the
transmitter housing are provided with a borehole to lock the cover.
The cover can be locked using screws and a chain or cable provided by the customer.
‣It is recommended to use stainless steel cables or chains.
‣If a protective coating is applied, it is recommended to use a heat shrink tube to protect the
housing paint.
1
1
2
2
1
1
5 (0.2) min. 15 (0.6)
SW 2.5
M3
A0029799
1 Cover borehole for the securing screw
2 Securing screw to lock the cover

Proline 500 Modbus RS485 Installation
Endress+Hauser 17
4.5 Transmitter post-installation check
The post-installation check must always be performed after the following tasks:
• Mounting the transmitter housing:
• Post mounting
• Wall mounting
• Turning the transmitter housing
• Turning the display module
Is the device undamaged (visual inspection)? 
Turning the transmitter housing:
• Is the securing screw firmly tightened?
• Is the connection compartment cover screwed on tightly?
• Is the securing clamp firmly tightened?

Turning the display module:
• Is the connection compartment cover screwed on tightly?
• Is the securing clamp firmly tightened?

Post and wall mounting:
Are the securing screws firmly tightened? 

Electrical connection Proline 500 Modbus RS485
18 Endress+Hauser
5 Electrical connection
NOTICE
The measuring device does not have an internal circuit breaker.
‣For this reason, assign the measuring device a switch or power-circuit breaker so that the
power supply line can be easily disconnected from the mains.
‣Although the measuring device is equipped with a fuse, additional overcurrent protection
(maximum 10 A) should be integrated into the system installation.
5.1 Electrical safety
In accordance with applicable federal/national regulations.
5.2 Connection conditions
5.2.1 Required tools
• For cable entries: Use corresponding tools
• For securing clamp: Allen key 3 mm
• Wire stripper
• When using stranded cables: crimper for wire end ferrule
• For removing cables from terminal: Flat blade screwdriver ≤ 3 mm (0.12 in)
5.2.2 Requirements for connecting cable
The connecting cables provided by the customer must fulfill the following requirements.
Protective grounding cable for the outer ground terminal
Conductor cross-section ≤2.08 mm2 (14 AWG)
Grounding impedance must be less than 2 Ω.
Permitted temperature range
• The installation guidelines that apply in the country of installation must be observed.
• The cables must be suitable for the minimum and maximum temperatures to be expected.
Power supply cable (incl. conductor for the inner ground terminal)
Standard installation cable is sufficient.
Cable diameter
• Cable glands supplied:
M20 × 1.5 with cable ⌀ 6 to 12 mm (0.24 to 0.47 in)
• Spring-loaded terminals: Suitable for strands and strands with ferrules.
Conductor cross-section 0.2 to 2.5 mm2 (24 to 12 AWG).

Proline 500 Modbus RS485 Electrical connection
Endress+Hauser 19
Signal cable
Modbus RS485
The EIA/TIA-485 standard specifies two types of cable (A and B) for the bus line which can be
used for every transmission rate. Cable type A is recommended.
For detailed information about the specification of the connecting cable, see the
Operating Instructions for the device.
Current output 0/4 to 20 mA
Standard installation cable is sufficient.
Pulse/frequency/switch output
Standard installation cable is sufficient.
Double pulse output
Standard installation cable is sufficient.
Relay output
Standard installation cable is sufficient.
Current input 0/4 to 20 mA
Standard installation cable is sufficient.
Status input
Standard installation cable is sufficient.
5.2.3 Connecting cable between the transmitter and sensor
4
3
1
2
A0041974
1 Non-hazardous area
2 Hazardous area: Zone 1; Class I, Division 1 or Zone 2; Class I, Division 2
3 Proline 500 transmitter
4 Prosonic Flow sensor set with sensor cable to transmitter 500 →  20
Transmitter and sensor installed in the hazardous area: Zone 1; Class I, Division 1 oder Zone 2;
Class I, Division 2

Electrical connection Proline 500 Modbus RS485
20 Endress+Hauser
Sensor cable for sensor - Proline 500 transmitter
Standard cable • TPE: -40 to +80 °C (-40 to +176 °F)
• TPE armored: -40 to +80 °C (-40 to +176 °F)
• TPE halogen-free: -40 to +80 °C (-40 to +176 °F)
• PTFE: -50 to +170 °C (-58 to +338 °F)
• PTFE armored: -50 to +170 °C (-58 to +338 °F)
Cable length (max.) 30 m (100 ft)
Cable lengths (available for order) 5 m (15 ft), 10 m (32 ft), 15 m (50 ft), 30 m (100 ft)
Operating temperature Depends on the device version and how the cable is installed:
Standard version:
• Cable - fixed installation 1): minimum –40 °C (–40 °F) or –50 °C (–58 °F)
• Cable - movable: minimum –25 °C (–13 °F)
1) Compare details under the "Standard cable" row