Endress+Hauser Prosonic S FMU90 User manual

BA288F/00/en/10.07
Valid as of software version
02.00.00
Operating Instructions
Prosonic S FMU90
Level Measurement
Alternating Pump Control
Rake Control
6

Table of Contents
3
Table of Contents
1 Safety Instructions . . . . . . . . . . . . . . . . 5
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Installation, commissioning, operation . . . . . . . . . . . 5
1.3 Hazardous area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Notes on safety conventions and symbols . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . 7
2.1 Parts of the Prosonic S FMU90 . . . . . . . . . . . . . . . . 7
2.2 Nameplate (Example) . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Product structure . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 Supplied documentation . . . . . . . . . . . . . . . . . . . . 10
2.6 Certificates and approvals . . . . . . . . . . . . . . . . . . . 11
2.7 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 11
3 Installation . . . . . . . . . . . . . . . . . . . . . 12
3.1 Incoming acceptance, transport, storage . . . . . . . . . 12
3.2 Mounting the field housing . . . . . . . . . . . . . . . . . . 12
3.3 Mounting the DIN-rail housing . . . . . . . . . . . . . . . 14
3.4 Mounting the remote display and operating module 17
3.5 Mounting of the sensors . . . . . . . . . . . . . . . . . . . . 18
3.6 Installation check . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Terminal compartment . . . . . . . . . . . . . . . . . . . . . 19
4.2 Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . 21
4.3 Sensor connection . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.4 Connection of the sensor heater (for FDU91) . . . . . 26
4.5 Connection of external switches
(for FMU90-********B***) . . . . . . . . . . . . . . . . 28
4.6 Connection of a temperature sensor . . . . . . . . . . . . 29
4.7 Shortening the sensor cable . . . . . . . . . . . . . . . . . . 31
4.8 Synchronization line. . . . . . . . . . . . . . . . . . . . . . . 32
4.9 Connection of the separate display and operating
module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.10 Potential equalization . . . . . . . . . . . . . . . . . . . . . . 33
4.11 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 34
5 Operation . . . . . . . . . . . . . . . . . . . . . . 35
5.1 Operating options . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.2 Operation via the display and operating module . . . 35
5.3 Operation via Endress+Hauser operating tool
("ToF Tool - Fieldtool Package" or "FieldCare") . . . . 48
5.4 Operation via HART handheld DXR375 . . . . . . . . . 48
5.5 Lock/unlock configuration . . . . . . . . . . . . . . . . . . 49
5.6 Reset to the default configuration . . . . . . . . . . . . . . 50
6 Commissioning. . . . . . . . . . . . . . . . . . 51
6.1 Structure and Functions of the Prosonic S . . . . . . . 51
6.2 First setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.3 Preparing the basic setup . . . . . . . . . . . . . . . . . . . . 54
6.4 Basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.5 Envelope curve display . . . . . . . . . . . . . . . . . . . . . . 71
6.6 After the basic setup . . . . . . . . . . . . . . . . . . . . . . . 71
7 The "display" menu . . . . . . . . . . . . . . 73
7.1 "display" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.2 "display format" . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
7.3 "back to home" . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8 The "Relay/Controls" menu . . . . . . . . 76
8.1 Configuration of a limit relay . . . . . . . . . . . . . . . . . 76
8.2 Configuration of an alarm or diagnostic relay . . . . . 81
8.3 Configuration of a pump control - standard . . . . . . 83
8.4 Configuration of a pump control - enhanced . . . . . . 96
8.5 Configuration of a rake control . . . . . . . . . . . . . . . 122
9 The "output/calculations" menu. . . . 127
9.1 The "allocation/calculations" submenu . . . . . . . . . 128
9.2 The "extended calibration" submenu . . . . . . . . . . 129
9.3 "HART settings" submenu
(only for current output 1) . . . . . . . . . . . . . . . . . . 132
9.4 "Simulation" submenu . . . . . . . . . . . . . . . . . . . . . 134
10 Troubleshooting . . . . . . . . . . . . . . . . 135
10.1 System error messages . . . . . . . . . . . . . . . . . . . . . 135
10.2 Possible calibration errors . . . . . . . . . . . . . . . . . . . 139
10.3 Envelope curve display . . . . . . . . . . . . . . . . . . . . . 140
10.4 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . 143
11 Maintenance and repairs . . . . . . . . . . 144
11.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 144
11.2 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
11.3 Repairs to Ex-approved devices . . . . . . . . . . . . . . 144
11.4 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
11.5 Replacing a sensor . . . . . . . . . . . . . . . . . . . . . . . . 144
11.6 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
11.7 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
11.8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
11.9 Contact addresses of Endress+Hauser . . . . . . . . . . 151
12 Accessories . . . . . . . . . . . . . . . . . . . . 152
12.1 Commubox FXA191 HART . . . . . . . . . . . . . . . . . 152
12.2 Commubox FXA195 HART . . . . . . . . . . . . . . . . . 152
12.3 Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . 152
12.4 Protection cover for the field housing . . . . . . . . . . 152
12.5 Mounting plate for the field housing . . . . . . . . . . . 153
12.6 Mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . 153
12.7 Adaption plate for remote display . . . . . . . . . . . . . 154
12.8 Overvoltage protection (in IP66 housing) . . . . . . . 154
12.9 Overvoltage protection HAW56x . . . . . . . . . . . . . 155
12.10 Extension cable for sensors . . . . . . . . . . . . . . . . . 158
12.11 Temperature sensor FMT131 . . . . . . . . . . . . . . . . 159

Table of Contents
4
13 Technical Data. . . . . . . . . . . . . . . . . . 160
13.1 Technical data at a glance . . . . . . . . . . . . . . . . . . 160
14 Operating menu . . . . . . . . . . . . . . . . 164
14.1 "level" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
14.2 "safety settings" . . . . . . . . . . . . . . . . . . . . . . . . . . 166
14.3 "relay/controls" . . . . . . . . . . . . . . . . . . . . . . . . . . 168
14.4 "output/calculations" . . . . . . . . . . . . . . . . . . . . . . 176
14.5 "device properties" . . . . . . . . . . . . . . . . . . . . . . . . 177
14.6 "system information" . . . . . . . . . . . . . . . . . . . . . . 178
14.7 "display" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
14.8 "sensor management" . . . . . . . . . . . . . . . . . . . . . 180
15 Appendix. . . . . . . . . . . . . . . . . . . . . . 181
15.1 Default block configuration . . . . . . . . . . . . . . . . . 181
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

Safety Instructions
5
1SafetyInstructions
1.1 Designated use
The Prosonic S FMU90 is a transmitter for the ultrasonic sensors FDU91, FDU91F, FDU92, FDU93,
FDU95 and FDU96. The sensors of the former class FDU8x can be connected as well.
The transmitter version for level measurements (product structure according to section 2.3:
FMU90 - *1**********) can be applied for different measuring tasks, e.g.:
• level measurement in tanks and silos
• conveyor belt measurement
• level limit detection
• (alternating) pump control
• screen and rake control
The version for level and flow measurements (product structure according to section 2.3:
FMU90 - *2**********) is usable for further measuring tasks, e.g.:
• flow measurement at open flumes and weirs
• (non-resettable) totalizers and (resettable) counters
• control of samplers by time or counting pulses
• backwater and dirt detection in flumes
• simultaneous measurement of level and flow in a stormwater overflow basin with only one sensor
1.2 Installation, commissioning, operation
The Prosonic S FMU90 is fail-safe and constructed to the state-of-the-art. It meets the appropriate
standards and EC directives. However, if you use it improperly or other than for its designated use,
it may pose application-specific hazards, e.g. product overflow due to incorrect installation or
configuration. Installation, electrical connection, start-up, operation and maintenance of the
measuring device must therefore be carried out exclusively by trained specialists authorised by the
system operator. Technical personnel must have read and understood these operating instructions
and must adhere to them. You may only undertake modifications or repair work to the device when
it is expressly permitted by the operating instructions.
1.3 Hazardous area
Measuring systems for use in hazardous environments are accompanied by separate "Ex
documentation", which is an integral part of this Operating Manual. Strict compliance with the
installation instructions and ratings as stated in this supplementary documentation is mandatory.
• Ensure that all personnel are suitably qualified.
• Observe the specifications in the certificate as well as national and local standards and regulations.
The transmitter may only be installed in suitable areas.
Sensors with a certificate for hazardous areas may be connected to a transmitter without a
certificate.
#Warning!
The sensors FDU83, FDU84, FDU85 and FDU86 with an ATEX, FM or CSA certificate are not
certified for connection to the FMU90 transmitter.
For installations in the USA:
Installation should be in accordance with the National Electrical Code NFPA 70 (NEC)
For installations in Canada:
Installation should be in accordance with the Canadian Electrical Code (CEC)

Safety Instructions
6
1.4 Notes on safety conventions and symbols
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding symbol in the margin.
Safety conventions
#Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to personal
injury, a safety hazard or destruction of the instrument
"Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to personal
injury or incorrect functioning of the instrument
!Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly affect
operation or may lead to an instrument response which is not planned
Explosion protection
0Device certified for use in explosion hazardous area
If the device has this symbol embossed on its name plate it can be installed in an explosion hazardous
area
-Explosion hazardous area
Symbol used in drawings to indicate explosion hazardous areas. Devices located in and wiring
entering areas with the designation “explosion hazardous areas” must conform with the stated type
of protection.
.Safe area (non-explosion hazardous area)
Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices located in
safe areas still require a certificate if their outputs run into explosion hazardous areas
Electrical symbols
%Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied
&Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be applied or
supplied
)Grounded terminal
A grounded terminal, which as far as the operator is concerned, is already grounded by means of an
earth grounding system
*Protective grounding (earth) terminal
A terminal which must be connected to earth ground prior to making any other connection to the
equipment
+Equipotential connection (earth bonding)
A connection made to the plant grounding system which may be of type e.g. neutral star or
equipotential line according to national or company practice
Temperature resistance of the connection cables
States, that the connection cables must be resistant to a temperature of at least 85 °C.
t >85°C

Identification
7
2 Identification
2.1 Parts of the Prosonic S FMU90
2.1.1 FMU90 in the field housing
L00-FMU90xxx-03-00-00-xx-001
(A): Display and operating module; (B): Cover of the terminal compartment; (C): Nameplate; (D): Instrument designation
and identification; (E): Short instructions; (F): Display cable; (G): Terminals; (H): Mounting help; (I): Grounding terminals;
(K): Prestamped openings for cable entries
2.1.2 FMU90 in the DIN-rail housing
L00-FMU90xxx-03-00-00-xx-003
(A): Display and operating module; (B): Cover of the terminal compartment; (C): Nameplate; (D): Instrument designation
and identification; (E): Short instructions; (F): Display cable; (G): Terminals
!Note!
The picture shows the smallest possible version of the DIN-rail housing. Depending on the version
of the Prosonic S, the width of the housing may be larger.
MadeinGermany
D-79689Maulburg
Prosonic S
Ta >60°C:
II3DT=xxx°CIP66/NEMA4X
XAxxxF-A
Dat./Insp.:
ifmodification
seesep.label
X=
10,5…32 VDC10W
4…20mAHART
OrderCode:
Ser.-No.: 5A01090109A
FMU90-J11AB111AA1A
MadeinGermany
D-79689Maulburg
Prosonic S
OrderCode:
Ser.-No.: 5A01090109A
FMU90-J11AB111AA1A
(A)
(B)
(H)
(C)
(D)
(E)
(F)
(G)
(I)
(K)
Made in Germany
D-79689 Maulburg
Prosonic S
Ta >60°C :
II3DT=xxx°CIP66/NEMA4X
XAxxxF-A
Dat./Insp.:
if modification
see sep. label
X=
10,5…32VDC10W
4…20mAHART
OrderCode:
Ser.-No.:5A01090109A
FMU90-J11AB111AA1A
Made in Germany
D-79689 Maulburg
Prosonic S
Ta >60°C :
II3DT=xxx°CIP66/NEMA4X
XAxxxF-A
Dat./Insp.:
if modification
seesep.label
X=
10,5 …32VDC10W
4…20mAHART
OrderCode:
Ser.-No.:5A01090109A
FMU90-J11AB111AA1A
(A) (B) (C) (D)
(E) (F) (G)

Identification
8
2.1.3 FMU90 with remote display and operating module for cabinet
door and switchboard mounting (96x96 mm)
L00-FMU90xxx-03-00-00-xx-002
(A): DIN-rail housing without display; (B): Remote display and operating module for cabinet mounting; the cable (3 m) is
supplied
!Note!
The picture shows the smallest possible version of the DIN-rail housing. Depending on the version
of the Prosonic S, the width of the housing may be larger.
2.2 Nameplate (Example)
L00-FMU90xxx-18-00-00-xx-001
(1): Order code (as defined by the product structure); (2): Serial number; (3): Power supply; (4): Output signal; (5):
Specification of required temperature resistance of the connection cables; (6): Certificate-related data; (7): Reference to
additional safety-relevant documentation; (8): Marked if a modification nameplate is present; (9): Specification of the
electrical protection class (protective insulation); (10): Ingress protection
MadeinG
ermany
D-79689Maulburg
Prosonic S
Ta >60°C :
II 3DT=xxx°C IP66/NEMA4X
XAxxxF-A
Dat./Insp.:
if modification
seesep. label
X=
10,5 …32VDC10W
4…20mAHART
OrderCode:
Ser.-No.: 5A01090109A
FMU90-J11AB111AA1A
3m
(A)
(B)
Made in Germany
D-79689 Maulburg
Prosonic S
Ta > 60°C :
II 3 D T=xxx°C
IP66 / NEMA4X
XAxxxF-A
Dat./Insp.:
if modification
see sep. label
X=
10,5…32VDC 10W
4…20mAHART
Order Code:
Ser.-No.: 5A01090109A
FMU90-J11AB111AA1A
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)

Identification
9
2.3 Product structure
(*): meaning of the language code:
cs: Czech; de: German; en: English; es: Spanish; fr: French; id: Bahasa (Indonesia, Malaysia); it:
Italian; ja: Japanese; ko: korean; nl: Dutch; pl: Polish; pt: Portuguese; ru: Russian; th: Thai; zh:
Chinese
2.4 Scope of delivery
• Instrument according to the version ordered
• ToF Tool - FieldTool Package
• for FMU90-***E********:
remote display and operating module; retainers; connection cable (3 m)
• for FMU90-*21********* FMU and for FMU90-*41*********:
2 slotted capstan screws (can be used to seal the housing)
• Accessories as ordered
10 Approval
R Non-hazarous area
JATEXII3D
N CSA General Purpose
20 Application
1 Level + pump control, alternating
2 Flow + totalizer + level + sample control + preprogrammed OCM flow curves
3 Level + additional pump control
4 Universal instrument (Level + Flow + Additional pump control)
30 Housing, material
1 Field mounting PC, IP66 NEMA 4x
2 DIN rail mounting PBT, IP20
40 Operation
C Illuminated display + keypad
E Illuminated display + keypad, 96x96, panel mounting, front IP65
K w/o display, via communication
50 Power supply
A 90-253 VAC
B 10,5-32 VDC
60 Level input
1 1x sensor FDU9x/8x
2 2x sensor FDU9x/8x
70 Switch output
11xrelay,SPDT
33xrelay,SPDT
66xrelay,SPDT
80 Output
1 1x 0/4-20mA HART
2 2x 0/4-20mA HART
3 PROFIBUS DP
90 Additional input
A w/o additional input
B 4x limit switch + 1x temperature PT100/FMT131
100 Datalog function
A Basic version
110 Languages
1 de, en, nl, fr, es, it, pt
2 en, ru, pl, cs
3 en, zh, ja, ko, th, id
120 Additional option
A Basic version
FMU90 - complete product designation

Identification
10
2.5 Supplied documentation
2.5.1 Operating instructions
(for transmitter FMU90)
Depending on the instrument version, the following operating instructions are supplied with the
Prosonic S FMU90:
These operating instructions describe installation and commissioning of the respective version of the
Prosonic S. It contains those functions from the operating menu, which are required for a standard
measuring task. Additional functions are contained in the "Descripiton of Instrument Functions" (BA
290F, see below).
2.5.2 Description of instrument functions
BA290F
contains a detailed description of all functions of the Prosonic S and is valid for all instrument
versions. A PDF file of this document can be found
• on the CD-ROM of the "ToF-Tool - FieldTool Package", which is supplied together with the
instrument
• in the internet at "www.endress.com"
2.5.3 Safety instructions
Additional safety instructions (XA, ZE, ZD) are supplied with certified device versions. Refer to the
nameplate for the names of the safety instructions that apply to your device version.
Operating instructions Output Application Instrument version
BA 288F
HART
• level measurement
• alternating pump control
• screen and rake control
FMU90 - *******1****
FMU90 - *******2****
BA 289F
•flowmeasurement
• backwater and dirt detection
• totalizers and counters
FMU90 - *2*****1****
FMU90 - *4*****1****
FMU90 - *2*****2****
FMU90 - *4*****2****
BA 292F
PROFIBUS DP
• level measurement
• alternating pump control
• screen and rake control
FMU90 - *******3****
BA 293F
•flowmeasurement
• backwater and dirt detection
• totalizers and counters
FMU90 - *2*****3****
FMU90 - *4*****3****

Identification
11
2.6 Certificates and approvals
CE mark, declaration of conformity
The device is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate. The device complies with the applicable
standards and regulations as listed in the EC declaration of conformity and thus complies with the
statutory requirements of the EG directives. Endress+Hauser confirms the successful testing of the
device by affixing to it the CE mark.
2.7 Registered trademarks
HART®
Registered trademark of HART Communication Foundation, Austin, USA
ToF®
Registered trademark of the company Endress+Hauser GmbH+Co. KG, Maulburg, Germany

Installation
12
3 Installation
3.1 Incoming acceptance, transport, storage
3.1.1 Incoming acceptance
Check the packing and contents for any signs of damage.
Check the shipment, make sure nothing is missing and that the scope of supply matches your order.
3.1.2 Transport, storage
Pack the measuring instrument so that it is protected against impacts for storage and transport. The
original packing material provides the optimum protection for this.
Permissible storage temperature: -40 ... +60 °C
3.2 Mounting the field housing
3.2.1 Dimensions of the field housing
L00-FMU90xxx-06-00-00-xx-001
Dimensions in mm
A: Mounting help (supplied); can also be used as drilling template ; B: Field housing; C: minimum mounting distance
The dimensions of the field housing are the same for all instrument versions.
To open the housing, a minimum mounting distance of 55 mm is required on the left.
215
180
150
15
170
190
80
100
∅7
10
A
B
153
C
³55 ³55
1,6 kg»

Installation
13
3.2.2 Installation conditions
Weather protection
In order to avoid excessive sunlight exposure, the instrument should be mounted in a position
which is protected against direct sunlight or a protection cover should be applied (s. chapter
"Accessories").
Overvoltage protection
In order to protect the Prosonic against overvoltages (especially if mounted outdoors), connection
of an overvoltage protection is recommended (s. chapter "Accessories").
Wall mounting
A mounting help for wall mounting is supplied. It also serves as drilling template. The mounting
help should be mounted on a flat surface and may not become distorted.
Pipe mounting
A mounting plate is available for mounting of the field housing to 1" - 2" pipes (s. chapter
"Accessories").
3.2.3 Installation
L00-FMU90xxx-17-00-00-xx-003
123
4

Installation
14
3.3 Mounting the DIN-rail housing
3.3.1 Dimensions of the DIN-rail housing
The dimensions of the DIN-rail housing depend on the instrument version. The version determines,
which terminal areas the Prosonic S contains. The dimensions are influenced by the following
features of the product structure (see chapter 2.3):
• 60: Level Input
• 70: Switch Output
• 80: Output
In order to determine the dimensions of a specific version, perform the following steps (see the
example on page 15):
1. Using the product structure, determine the options of the features 60, 70 and 80 of the
instrument version in question.
2. Using the following table, determine how many optional terminal areas this instrument version
contains.
3. The appropriate dimensions are given in the following diagram:
10 20 30 40 50 60 70 80 90 100 110 120
FMU90 -
Feature and option of
the product structure
corresponds to the following
terminal area
present?
yes = 1
no = 0
feature 60; option 2
and/or
feature 80, option 2
2 sensor inputs
and/or
2 analogue outputs
feature 70, option 3 or 6 3 o 6 relays
feature 80, option 3 PROFIBUS DP interface
feature 90, option B inputs for external switches and
external temperature sensor
Sum =
Sum = 0
(only basic terminal area)
L00-FMU90xxx-06-00-00-xx-002
Dimensions in mm
Sum = 1, 2 or 3
(1-3 optional terminal areas)
L00-FMU90xxx-06-00-00-xx-005
Dimensions in mm
92
104
140
≈0,5 kg
43
EN 60715
TH 35x7,5/15
35
150
104
140
≈0,7 kg
42
EN 60715
TH 35x7,5/15
35

Installation
15
Example
Sum = 2
=> 104 mm x 150 mm x 140 mm
Sum = 4
(4 optional terminal areas)
L00-FMU90xxx-06-00-00-xx-009
Dimensions in mm
43
EN 60715
TH 35x7,5/15
35
104
210
140
≈0,9 kg
10 20 30 40 50 60 70 80 90 100 110 120
FMU90 - R 1 2 A A A 1 A
feature and option of
the product structure
corresponds to the following
terminal area present?
feature 60; option 2
and/or
feature 80, option 2
2 sensor inputs
and/or
2 analogue outputs
1 (yes)
feature 70, option 3 or 6 3 or 6 relays 1 (yes)
feature 80, option 3 PROFIBUS DP interface 0 (no)
feature 90, option B inputs for external switches and
external temperature sensorr 0 (no)
Sum = 2
232A

Installation
16
3.3.2 Installation conditions
• The DIN-rail housing must be mounted outside hazardous areas in a cabinet.
• The housing is mounted on a DIN rail EN 60715 TH 35x7,5 or TH 37x15.
• Do not install the instrument in the vicinity of high-voltage lines, motor lines, contactors or
frequency converters. The installation regulations for high-voltage lines, motor lines, contactors
or frequency converters must be observed.
• To ensure easy mounting and opening of the housing, a distance of approx. 1 cm should be kept
between the instruments.
• In order to avoid interference signals, the sensor cables must not be laid parallel to high voltage
or electric power lines.
• The cables may not be laid in the proximity to frequnecy converters.
3.3.3 Mounting
L00-FMU90xxx-17-00-00-xx-001
A: Attaching the instrument to the rail; B: Detaching the instrument from the rail
a
b
EN 60715 TH 35x7,5
EN 60715 TH 35x15
AB
b
a

Installation
17
3.4 Mounting the remote display and operating module
3.4.1 Scope of delivery
If the Prosonic S is ordered with the display for cabinet door mounting, the following is contained
in the scope of delivery:
• Display and operating module, 96x96 mm
• 4 retainers (with nuts and screws)
• Connection cable (3 m) for connection to the transmitter
(preassembled with suitable plugs).
3.4.2 Dimensions of the separate display and operating module
L00-FMU90xxx-06-00-00-xx-004
Dimensions in mm
3.4.3 Mounting
1. Cut an opening of 92 x 92 mm into the intended mounting position (e.g. cabinet door).
2. Insert the remote display module into the opening and fix the retainers as shown in the
following figure:
L00-FMU90xxx-17-00-00-xx-002
96
55
max. 6
92 min. 11
≈0,5 kg
(a) (b)
(c)
(d)

Installation
18
3.4.4 Adaption plate
If an opening of 138 mm x 138 mm and the remote display of the Prosonic FMU860/861/862 are
already present, you can use the adaption plate (Order Code: 52027441, s. chapter "Accessories").
It is inserted into the remote display of the FMU860/861/862.
!Note!
The adapter plate is mounted directly in the housing of the old remote display of the FMU86x series.
The housing of the remote display of the FMU86x is the holder for the adapter plate and the new
remote display of the FMU90/FMU95 in the format 96x96 mm.
L00-FMU90xxx-06-00-00-xx-006
(a): Remote display of the FMU90 with adaption plate; (b): Remote display of the FMU 860/861/862
3.5 Mounting of the sensors
Information on the mounting of the sensors can be found in the following documents:
• Technical Information TI 189F (for FDU8x)
• Technical Information TI 396F (for FDU9x)
These documents are supplied with the sensors.
3.6 Installation check
After installing the device, carry out the following checks:
• Is the device damaged (visual inspection)?
• Does the device correspond to the meausring point specifications such as process temperature,
process pressure, ambient temperature, measuring range etc?
• If available: Are the measuring point number and labelling correct?
• Is the instrument sufficiently protected against rainfall and direct sunlight?
• For the field housing: Are the cable glands tightened correctly?
• Is the instrument securely mounted to the DIN rail or the mounting help (visual inspection)?
• For the field housing: Are the screws of the terminal compartment cover securely tightened
(visual inspection)?
(a)
(b)

Wiring
19
4 Wiring
#Warning!
The instrument may only be installed if the supply voltage is switched off.
4.1 Terminal compartment
4.1.1 Terminal compartment of the field housing
The field housing has a separate terminal compartment. It can be opened after loosening the four
screws of the lid.
L00-FMU90xxx-04-00-00-xx-002
For easier wiring, the lid can be completely removed by unplugging the display plug (1) and pulling
off the hinges (2):
L00-FMU90xxx-04-00-00-xx-009
4.1.2 Cable entries of the field housing
The following openings for cable entries are prestamped on the bottom of the housing :
• M20x1,5 (10 openings)
• M16x1,5 (5 openings)
• M25x1,5 (1 opening)
The required number and types of cable entries depend on the application at hand.
The prestamped openings can be removed by a suitable tool (e.g. knife or boring bit) or by punching
them out cautiously.
1
2
1
1
1
3
12

Wiring
20
4.1.3 Terminal compartment of the DIN-rail housing
Single instrument
l00-fmu90xxx-04-00-00-xx-003
The catch can be unlocked by slightly pressing onto the clip. Then, the cover of the terminal
compartment can be opened.
Several instruments mounted side by side
L00-FMU90xxx-04-00-00-xx-012
1. Open the catch of the cover (e.g. by a screwdriver).
2. Pull the cover out by approx. 2 cm.
3. The cover can now be opened.
!Note!
• The cables can be inserted into the housing from above or from below.
• The pictures show the smallest housing version but are valid for the larger versions as well.
• If the instruments are mounted next to each other and if the sensor cables run in parallel, the
synchronization terminals (39 and 40) must be interconnected (see sections "Terminal
assignment" and Synchronization line").
12
a
b
12
3