Enelion Stilo User manual

Stilo
Quick Guide
Congratulations on your purchase of Enelion Stilo charger and thank you for
trusting us. Before the installation make sure that the box contains all ac-
cessories: Enelion Stilo charger, a short version of the User Manual, a RFID
card, Torx T25 bit, wall mounting template.
The current version of the manual and installation
guide is available at http://enelion.com/en/help/
Introductory information
Enelion Stilo weights 4850 g. The device is not provided with wall an-
chors/screws. These should be selected according to the device weight and
the holes in the wall.
The device should be mounted onto a flat vertical, using the 4 holes with
5,5 mm diameter at the back of the device. Use countersunk screws only.
The device is accompanied by a template to enable easy mounting and mark-
ing the mounting points. The manufacturer is not liable for damages resulting
from incorrect installation of the device on the wall. Installation should be
carried out by a competent person who has read the requirements of this
manual and is equipped with the tools necessary for proper installation.
Preparing the wiring system
Power service connection for the charging terminal must be equipped with a
proper overcurrent circuit breakerwhich is proper for the available power ca-
pacity in the connection, the charger configuration and the power supply. The
overcurrent circuit breaker also functions as the charging station main switch.
The wire cross-section must be selected based on the current configured in
the charger and the wire length.
To be compliant with the PN-EN IEC 61851-1: 2019-10 standard, each charg-
ing point must also be protected against type A or B residual current. This
requirement must be met by one of the below:
1. RCD type B ( 30 mA/40 A) or RCD EV (30 mA/40 A) in the switch-
board,
2. RCD typu A ( 30 mA/40 A) in the switchboard with the application of
Enelion RCM B - attached to the charging terminal.
The charger’s supply line connected directly to the counter should be sepa-
rated from other devices.
Opening the device
The device comes in a closed casing. In order to open the device it is neces-
sary to use a Torx T25 bit provided with the device. Closing of the device is
performed by repeating the steps in the reverse order.
1. Locate the device closing bolt and remove it, using the torx T25 bit
(included) and a screw driver.
2. Hold the casing and slide it up the guiding grooves to remove it.
3. Store the casing in a safe place.
;
oWARNING
Be careful not to crimple the signal tape while fitting the
front panel.
Mounting the device
1. Determine the target position of the device using the attached tem-
plate and the level and mark the mounting holes.
2. Make mounting holes in the wall and install wall expansion bolts.
3. Put the wall anchor to the holes and fix it with bolts.
4. Make sure there is no voltage on the power supply cable and prepare
it according to the instruction.
5. Open the charging terminal according to the instructions in Section
Opening the device.
6. Put the open device to its final position by threading the power cord
through the gland of the down side of the housing (hole A) and hook
it on the previously installed anchor.
oWARNING
Cables connection should be done according to the dia-
gram. Pay attention to the order of phases, according to
the description at connectors.
7. Optionally Insert the length of at least 35cm of the communication
cables into the device.
8. Fix the device to the wall anchor with a mounting screw.
9. Screw on the power cable gland ensuring tightness.
10. Secure the hook of the charging cable with the fastening screws.
11. Push from up side closing the aluminum housing onto the device from
the top and secure it from the side with an anti-theft screw, according
to the information in the section Opening the device.
oWARNING
The connection must be made by a person with the right
qualifications.

oWARNING
The manufacturer is not liable for damages resulting from
not following the connection diagram presented above and
not ensuring proper wire connection.
oWARNING
Fixing the device firmly is crucial to its proper operation
when in service.
INFO
More detailed information is in the Stilo Assembly Manual.
Preparing for use
Before the initial use of the charger make sure that:
1. The charger has been properly installed and poses no risk to the
safety of the user.
2. The charger starts properly and informs about being ready to use -
led bar flashing blue.
3. The charging station has been configured properly and interaction
with the user is going in the correct and intuitive way.
Starting to charge
In order to start charging a car place the user card onto the RFID reader lo-
cated behind the top cover. Applying the correct card will be signaled with
lightning a sequence of diodes on a light bar in green and in one direction.
Once the card is accepted:
1. connect the charging cable to the car,
2. make sure, that charging started.
After performing those actions the charger will enter into the charging mode,
which is communicated with a green light on the light bar. When charging the
light bar will pulsate, radiating from the center towards the edges. A uniform
green color on the light bar means the charger is ready for charging and is
waiting for response from the car.
Finishing charging
In order to finish the charging process disconnect the charging cable from
the car. It will cause the charger will return to stand-by. In case of RFID con-
figuration applying the correct card once more will also result in stopping the
charging process.
Technical data
Mechanic specifications
Dimensions (width x height x
depth)
185 mm x 430 mm x 56 mm
Weight 4,85 kg
IP Class IP54
Mechanical strength class IK10
Electrical specifications
Power supply cable
cross-section
Suggested minimal cross-section:
• 5 x 2,5 mm2(nominal current 16 A)
• 5 x 6,0 mm2(nominal current 32 A)
Supply voltage (Europe) 3 x 230 V/400 VAC(+-10%)
Voltage frequency 50 Hz/60 Hz
Type of network TN, TT
Overcurrent protection Not part of the device. The protection
must be made in compliance with the
local regulations and with the device
version.
Residual current device RCD B switch or Enelion RCM B +
RCD A
Protection class Class I
Cable variant Type 2, standard plug 32 A/400 VAC
according to EN 62196-1
Environment
Working temperature from −25 °C to 55 °C
Storing temperature range from −40 °C to 80 °C
Acceptable relative air humidity from 5% to 95%
Altitude maximum 2000 m
© 2021 ENELION
The instruction may be changed as the product develops. There
is no guarantee as to the accuracy of the provided information. All
rights reserved.
Document version: V 1.2
Date of issue: April 30, 2021
ENELION Sp. z o.o.
ul. Pana Tadeusza 50, 80-123, Gda´ nsk, Polska
www.enelion.com