Energetics CT 570 User manual

1
CT 570 ERGOMETER BIKE
GB
D
CZ
SK
H

2
Table of contents - Inhaltsverzeichnis - Obsah - Obsah - Tájékoztató
1. English P. 3
2. Deutsch P. 17
3. esky P. 33
4. Slovensky P. 48
5. Magyar P. 63
© The owner’s manual is only for the customer reference. ENERGETICS can not guarantee for mistakes occurring due to translation or
change in technical specification of the product.
©Die Gebrauchsanweisung dient nur zur Referenz für den Kunden. ENERGETICS übernimmt keine Haftung für Fehler die durch
Übersetzung oder technische Änderungen des Produkts entstehen.
©Návod k použití je pouze doporuení pro zákazníky. ENERGETICS nepebírá žádné ruení za chyby zpsobené pekladem i
zmnami v technické specfikaci výrobku.
© Tento návod je urený len pre potrebu zákazníkov. ENERGETICS nezodpovedá za chyby, ktoré sa môžu vyskytnúkvôli chybnému
prekladu alebo zmenám v technickej špecifikácii produktu.
© A használati útmutató kizárólag felhasználói referenciaként szolgál. az ENERGETICS nem vállal felelsséget a fordítási hibákból vagy
a termék mszaki módosításaiból eredhibákért.
© Copyright by ENERGETICS

3
Dear Customer,
Congratulations on your purchase of an ENERGETICS home exerciser. This product has been designed and
manufactured to meet the needs and requirements of in-home use. Please carefully read the instructions prior to assembly
and first use. Be sure to keep the instructions for reference and/ or maintenance. If you have any further questions, please
contact us. We wish you lots of success and fun while training,
Your - Team
Warranty
ENERGETICS offers high quality home exercisers that have been tested and certified according to European Norm EN
957.
ENERGETICS warrants to the original purchaser 3 years against possible defects in material and workmanship. Excluded
are damages caused by misuse and wearing parts. All electronic parts are warranted for a period of 2 years. The warranty
period starts at the date the product was purchased (retain your sales receipt).
Safety Instructions
•Consult your physician before starting with any exercise programme to receive advice on the optimal training.
•Warning: incorrect/ excessive training can cause health injuries. Stop using the home exerciser when feeling
uncomfortable.
•Ensure that training only starts after correct assembly, adjustment and inspection of the home exerciser.
•Always start with a warm-up session.
•Only use original ENERGETICS parts as delivered (see checklist).
•Follow the steps of the assembly instruction carefully.
•Only use suitable tools for assembly and ask for assistance if necessary.
•Place the home exerciser on an even, non-slippery surface.
•Use the height adjustment caps on the rear tube to ensure a stable position of the home exerciser.
•Make sure the front wheels are placed in the correct position: see assembly instruction.
•For all adjustable parts be aware of the maximum position to which they can be adjusted.
•Tighten all adjustable parts to prevent sudden movement while training.
•This product is designed for adults. Please ensure that children only use it under the supervision of an adult.
•Ensure that those present are aware of possible hazards, e.g. movable parts during training.
•The resistance level can be adjusted to your personal preference.
•Do not use the home exerciser without shoes or loose shoes.
•Ensure that sufficient space is available to use the home exerciser.
•Be aware of non-fixed or moving parts whilst mounting or dismounting the home exerciser.
The resistance can be changed by computer.
-This product is made for home use only and tested up to a maximum body weight of 130 kilograms.
-Keep special attention to the minimum insertion depth of the seat post.
GB

4
Pre-assembly notes
OPEN THE BOXES
Make sure to inventory all the parts that are included in the boxes. Check The Hardware Chart
for a full count of the number of parts included for proper assembly.
GATHER YOUR TOOLS
Before starting the assembly of your unit, gather the necessary tools. Having all of the equipment at
hand
will save time and make the assembly quick and hassle-free.
CLEAR YOUR WORK AREA
Make sure that you have cleared away a large enough space to properly
assemble the unit. Make sure the space is free from anything that may cause
injury during assembly. After the unit is fully assembled, make sure there is a
comfortable amount of free area around the unit for unobstructed operation.
Hardware chart
5 M8 WASHER (T=1.2) 10
6 M8 SPRING WAHER 10
7 M8 CP NUT 2
10 M8*15mm ALLEN HEAD SCREW 8
4 M8*52mm CARRIAGE BOLT 2
21 SEAT KNOB 1
87 ALLEN KEY 1
89 TOOL 1
90 TOOL 1

5
Part list
NO. DESCRIPTION Q'TY
NO.
DESCRIPTION Q'TY
1 BASE FRAME 1 46 HANDLEBAR CAP 2
2 FRONT FOOT 1 47 SCREW M8 * 25 mm 2
3 FRONT FOOT COVER(L&R) 2 48 SERVO MOTOR 1
4 M8 * 52 mm CARRIAGE BOLT 2 49 DRIVE WIRE ROD WHEEL 1
5 M8 WASHER (t=1.2) 11 50 CLIP C5 (ID 4.7mm) 1
6 M8 SPRING WASHER 12 51 M6*10mm SCREW 2
7 M8 CAP NUT 2 52 SENSOR BRACKET 1
8 REAR FOOT 1 53 SENSOR WIRE 1
9 REAR FOOT COVER 2 54 #6-32 *12mm SCREW 1
10 M8*15mm ALLEN HEAD SCREW 8 55 WIRE ROD 1
11 LEFT CHAIN COVER 1 56 SMALL SPRING 1
12 RIGHT CHAIN COVER 1 57 M8 NYLON NUT 1
13 HANDLEBAR POST 1 58 M8*52MM HEX HEAD BOLT 1
14 COMPUTER UPPER CABLE 1 59 MAGNETIC HOLDER 1
15 COMPUTER LOWER CABLE 1 60 BEARING (6203ZZ) 4
16 SADDLE POST 1 61 CLIP C17(ID 15.7mm) 3
17 DC CABLE 1 62 MAGNET 1
18 MOVABEL SEAT POST 1 63 REAR PULLEY 1
18A SADDLE POST HOLDER 1 64 WASHER ID17 OD22 <t = 0.3 mm > 1
19 SADDLE 1 65 AXLE FOR PULLEY 1
19A SADDLE BRACKET 1 66 M6*15mm SCREW 4
20 MOVABEL SEAT POST KNOB 1 67 BELT 1
21 SEAT KNOB 1 68 M8*15mm HEX HEAD SCREW 2
22 COMPUTER 1 69 MAGNETIC HOLDER BRACKET 1
23 M5*12mm SCREW 4 70 BRACKET 1
24 HAND PULSE WIRE 1 71 LARGE SPRING 1
25 FOAM GRIP 2 72 SPACER SLEEVE 3
26 HAND PULSE

PE16

2 73 M6*1.5mm WASHER 3
27 HANDLEBAR 1 74 M6*14mm SCREW 3
28 FRONT POST COVER 1 75 BEARING (6300ZZ) 1
29 SADDLE POST COVER 1 76 FRONT PULLEY 1
30 HANDLEBAR SCREW 1 77 FLYWHEEL 1
31 SCREW M5 * 12 mm 14 78 FLYWHEEL AXLE 1
32 3/8" WH NUT 2 79 BEARING (6003ZZ) 2
33 PEDAL (L/R) 1 80 BEARING IC1735-FT 1
34 CROSS FRAME(R) 1 81 WASHER ID30 OD34 (0.8mm) 1
35 ADAPTOR 1 82 BEARING (6000ZZ) 1
36 TURNING PLATE (R) 1 83 M10 WASHER (t=1mm) 1
37 3/8" NUT (t=3mm) 1 84 3/8" NUT (t=7mm) 1
38 TURNUNG PLATE COVER 2 85 CLIP C10(ID 9.1mm) 1
39 SADDLE SUPPORT TUBE INSERT 1 86 CROSS FRAME(L) 1
40 TURNING PEDAL (L) 1 87 BACK HANDLEBAR COVER 1
41 ROUND SCREW FOR ADJ.HEIGHT 2 88 FRONT HANDLEBAR COVER 1
42 M10 WASHER (t=2mm) 3 89 SCREW M3 * 12 mm 2
43 PLASTIC PAD 1 90 SCREW M5 * 10 mm 2
44 FIX PLATE 1
45 PLASTIC BUSH 2

6
Exploded Drawing

7
Assembly
ALL THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE
FACTORY.

8
STEP 1
Fasten Front Stabilizer (2) to the Base (1) using 2 x (4),
2 x (5), 2 x (6) and 2 x (7). Tighten with the spanner.
Note: It will help to place a piece of the polystyrene
packaging under the bike when assembling the
front stabilizer.
STEP 2
Fasten Front Stabilizer (2) to the Base (1) using 2 x (4), 2
x (5), 2 x (6) and 2 x (7). Tighten with the spanner.
Note: It will help to place a piece of the polystyrene
packaging under the bike when assembling the front
stabilizer.
STEP 3
Connect computer Upper Cable (14) to Computer
Lower Cable (15). A click can be felt when pushing
The two parts together. Insert the handlebar post
through the plastic cover and into the base and
attach it with 4 x (10), 4 x (6) and 4 x (5). Tighten
with the Allen key. Push plastic cover over the
Allen head bolt once tightened.
Step 4
Attach the Saddle Bracket (19A) to the Saddle Post holder
(18A).
Note: It may help to turn the saddle upside down.
Place it on a piece of plastic to protect it. Tighten
With the spanner.
Step 5
Insert the Saddle Post (16) into the Base. Align one of
the holes in the saddle post with the hole in the Base
and insert the Seat Knob (21) through the hole in the
Base into the hole in the Saddle Post. Tighten the Seat
Knob into the Base.

9
Step 6
Attach the Handlebar (27) to the Handlebar Post (13) and
secure with clamp, clamp decoration cover (87), star
handle screw (30) and washer (5) in your desired position.
Attach the handlebar cover (87+88)
with 2 screws M5x10mm (90).
Step 7
Attach the Computer Upper Cable (14) to the Computer
(22). A click can be felt when the Cable is attached.
Attach the Computer (22) to the Handlebar Post with 4 x
(23). Tighten with the screwdriver.
Step 8
Insert the Right Pedal (33) into the right arm of the Crank
assembly(34) and finger tighten in a clockwise direction
until the thread is fully inserted in the crank.
Repeat for the Left Pedal (33) finger tighten in an
anticlockwise direction. Tighten both with the spanner.
Step 9
Plug the Adaptor (35) into the rear of the bike and into the
main power, the console will beep when connected and
the power is turned on.
Well done !
Your bike is now ready for use. Please go to the computer operation section in this
manual for instructions on how to operate your console.

10
Computer Instruction
Rotation/ Minute (U/min)
Recovery -
to get fitness note
Start/ Stop - to start or pause
training by pressing the nut
Energy consumption
(cal.)
ZEIT (min; sec.)
EINGABE- to enter
training parameters
AB - to adjust data and
resistance by turning the
nut to left
Display for active Program
Level – display for active
resistance level (1~16)
Current Heart Rate
(BPM)
USER – to store user
personal data
GESCHWINDIGKEIT
(Km/h.)
Watt
Start or Stop
status
User no. 1~4
Display current
function value
Display active function
Display for active profile & resistance
STRECKE (Km)
AUF - to adjust data and
resistance by turning the
nut to right