Ergotron Zido ZAH25CG/CG4 User manual

1 of 4
300-5418-00 rev. R • 10/19
Zido Adjustable, NO LIP Part#
Adjustable, Heavy Load, 25" w ZAH25CG/CG4
Adjustable, Light Load, 22" w ZAL22CG/CG4
Adjustable, Light Load, 25" w ZAL25CG/CG4
www.ergotron.com | USA: 1-800-888-8458
For the latest User Installation Guide please visit:
Zido®Adjustable-Height Cart
User Guide

2 of 4
300-5418-00 rev. R • 10/19
09
10
11
01
02
03
04
06
05
07
08
Product Quantity
01 Cap Shelf 1
For small cart, no lip
For small cart, with lip
For large cart, no lip
For large cart, with lip
02 Cap Shelf Bracket 1
03 Base
For Small Cart 1
For Large Cart 1
04 Column
For Light Load Cart 1
For Heavy Load Cart 1
05 4" Non-locking Caster 2
06 4" Locking Caster 2
07 Release Lever and Paddle 1
08 5/16-18 Nylock Nut 4
09 5/16-18 Button Head Screw 4
10 1/4-20 UNC Flat Head Screw 2
11 3/4" Wood Screws 8
12 3/16" Hex Key (not shown) 1
13 5/32" Hex Driver (not shown) 1
PARTS LIST
Before beginning assembly of your Zido Height-adjust-
able Cart, please review the parts list to verify that your
shipment is complete.

3 of 4
300-5418-00 rev. R • 10/19
1/4-20 UNC Flat Head Screw
STEP 2
Connect the Base with the Tube
Holding the column from the center (don't push
from the top) slide the tube into the base so
that the tube goes all the way to the bottom of
the base.
Align the upper hole on the base with a
threaded hole in the column. (For the large
cart, you'll use the top hole; for the small cart,
you'll use the second hole.) Loosely attach the
column to the base with two 1/4-20 UNC Flat
Head Screws.
STEP 1
Insert the Casters into the Base
Place the base upside down. Use a
rubber mallet to tap the locking casters
into the front receivers of the base.
Tap the non-locking casters into the
receivers of the base.
ASSEMBLY SEQUENCE
Plan out the assembly sequence to make your installation easier.
1. Pre-drill the top for accessories (Mouse Holder, Side Bin, Gel Cup/Probe Holder, Extension Tube).
2. Assemble the cart.
3. Base Storage Shelf.
4. Drawer, Keyboard Caddy, Standard Handle.
5. Additional Shelves, Equipment Shelves, Metal Bin.
6. Cable Bin, Glove Box Holder.
7. Mouse Holder, Side Bin, Gel Cup & Probe Holder, Extension Tube.
8. 8" Handle, Flat Panel Mounts.

4 of 4
300-5418-00 rev. R • 10/19
5/16-18 Button
Head Screw
Lock Nuts
© 2016 Ergotron, Inc. All rights reserved.
www.ergotron.com | USA: 1-800-888-8458
5/16-18 Button Head Screw 5/16-18 Nylock Nut
3/4”Wood Screws
STEP 3
Install the Lever and the Top Plate
Align the lever with the top of the trunk
assembly as shown.
Locate the bracket. The bottom of the bracket
is at and has no sticker. The top of the bracket
has a sticker that says "TOP" and has bumps with
threads inside. The bumps on the top of the
bracket will nest inside the holes on the cap shelf.
Align the cap shelf bracket with the trunk assembly so the bracket's tabs
are at the back and the "TOP" label is on top.
Using the 3/16 hex key, insert four 5/16-18 Button Head Screws through
the holes on the top of the Top Plate and capture with four 5/16-18 Nylock
Nuts inserted in to the holes in the top of the columns.
Pull up on the lever to move the column up and down. Repeat a few
times to make sure the column moves smoothly. If the lever was installed
upside down, the column won’t move. If that happens, remove the top
plate, invert the lever, and try it again.
STEP 4
Install the Cap Shelf
Align the indentations on the bottom of the cap shelf with the screw
heads and bumps on the top of the top plate.
Secure the cap shelf to the cart with eight 3/4" wood screws.
Tighten the 1/4-20 UNC Flat Head Screws that connect the column to the
base.
Pull the paddle up and move the column up and down a few times to
loosen the mechanism. Be sure to operate the column from the back of
the cart so you have plenty of leverage.
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
For the latest User Installation Guide please visit: www.ergotron.com