15
D1 D2 Parameter D3 D4
Pre-set
option
Options or values
C0Number of operators 01, 201
(VIVO-I103)
02
(VIVO-I203)
01: one operator,
02: two operators (only available with C301)
1Operator 1 turning direction
(operator 2 also changes) 01, 20101: direction A, 02: direction B. Check direction by
pressing UP (open) and DOWN (close)
2Operator 2 turning direction
(operator 1 also changes) 01, 20101: direction A, 02: direction B. Check direction by
pressing UP (open) and DOWN (close)
3Type of gate 01...30101: swing, 02: sliding, 03: up-and-over
4Opening safety device
(photocell) 0,10,10000: not installed,
10: no testing, 11: with testing
5Closing safety device (photocell)
Closing photocell with C520 or
C521, also prevents the start of
gate opening
0...20,10000: not installed,
10: no testing,
11: with testing,
20: no testing,
21: with testing
6Electrolock / electromagnet
C630 and C640 are used to
manage an external relay at
24Vdc, connected to cable
connectors P11-P12. The
electromagnet must be
externally supplied (through this
relay) and sized in line with the
electromagnets used.
0...40...40000: not installed
1X: electrolock without reverse impulse.
Programmable electrolock time: 3 seconds
with X=0(by default), 3.5s with X=1, 4s with
X=2, 4.5s with X=3, 5s with X=4.
2X: electrolock with reverse impulse.
Programmable time (electrolock/motor
reverse): 4.5/1.5 seconds with X=0(by default),
5/2s with X=1, 5.5/2.5s with X=2, 6/3s with
X=3, 6.5/3.5s with X=4.
30: electromagnet without impulse
40: drop electromagnet
7Encoder / Limit switches
The connections depend on the
type of operator selected (C301,
C302 or C303); see the
corresponding wiring diagram)
00...50000: not installed; 01: with single encoder;
02: with limit switches;
03: with dual encoder;
04: with encoder and limit switches (not available
with C301 selected);
05: VULCAN VUS and ATLAS (ATS) G6xxI (only
available with C301 or C303 selected)
8Radio card 01, 20201: RSD card (non-decoding);
02: two-channel decoder card
9Safety strip 01, 20101: mechanical; 02: resistive 8k2
ASlowdown 00...30100: no slowdown;
01: slowdown in opening and closing;
02: slowdown in opening;
03: slowdown in closing
P1
Total opening radio programming
oç Programmes total opening code and channel
2Pedestrian opening radio
programming oç Programmes pedestrian opening code and channel
3Gate open/close programming oç Programmes the operations in accordance with
configuration CA
F1Key command using ST1 and
ST2 pushbuttons.
With
F101
the gate (total or
pedestrian) can be kept open by
keeping ST1 or ST2 pressed down
respectively. This allows the time
scheduler to be used in combination
with
F2
and/or
F4
K
00
.
00...40100: ST1 and ST2 without effect, key commands are
made by radio (channel 1: total opening-
closing, channel 2: pedestrian opening-closing)
01: ST1 total opening-closing, ST2 pedestrian
opening-closing
02: ST1 total opening, ST2 total closing
03: dead-man mode (the display shows HP);
04: dead-man mode in closing
2Automatic or step-by-step
operation mode and standby
time (in seconds) in automatic
mode
0..5.0...90000: step-by-step mode
01: automatic mode and stand-by time 1 second;
...
59: automatic mode and stand-by time 59 sec.;
1.0: 1 min. 0 sec.;
...; maximum 4 minutes
3Pedestrian opening (%) 0...90...94000: pedestrian opening is not carried out,
10: 10% of the total opening, etc
4Pedestrian closing mode 0...50...90000: step-by-step mode
01: automatic mode and stand-by time 1 second;
...
59: automatic mode and stand-by time 59 sec.;
1.0: 1 min. 0 sec.;
...; maximum 4 minutes
Complete programming table (I)
