Esco 10961 User manual

Part No. 10961
ON
LIGHT
UNIT
DIGITAL T I RE INFLATOR
Operating Instructions
* Tire pressure measuring instruments,
devices for inspection of pressure and/or
inflation/deflation of tires for motor
vehicles.

2
Digital Tire Inflator
Thank you for selecting the Digital Tire Inflator.
Please read this manual before carrying out any
installation or service procedure. This manual is
an integral and essential part of the product,
please keep it away from damp, heat, dust, oils,
do not remove, tear or amend any parts of the
manual for any reason. It must be made
available to the operator and tomaintenance
personnel, also to ensure staff training. If you
lose or damage the manual, ask the
manufacturer for a copy, quoting the Part No.
The manual must always remain with the
machine, in the event of the machine being
sold, it must be given to the new user. The
manufacturer reserves the right to change
product features at any time without notice.
IMPORTANT
This tire inflator must only be connected to air
line systems which have clean dry air. Any
moisture in the air line system may cause
damage to the operation of this tire inflator
and void warranty.
Air pre-filters must be used with this inflator to
ensure product accuracy and longevity.
Features
■Auto ON, upon air pressure sensing
■Large tilted LCD display with backlight and
90 second auto OFF
■IP rating = IP44
■Multi scale gauge
■Die cast aluminium unit with impact bumper
and lightweight ABS handle and trigger
■Supplied with ofcial calibration certicate
■Wire sheathed hose on ex area of hose to
eliminate kinking
■Lightweight and robust
■Complies with EN12645: 2014*
Operation
■To read pressure:
Remove tire valve cap.
With clip-on air chuck lever depressed, firmly
press chuck onto tire valve stem and release
lever, ensure that no air leaks.
Check pressure gauge, the digital display will
activate once the tire pressure is sensed. If no
pressure is sensed the display will not turn on.
Press the tire inflator lever to add air into the
tire, before reading the pressure.
■To inflate:
With clip-on air chuck lever depressed, firmly
press chuck onto tire valve stem and release
lever, ensure that no air leaks.
Fully depress the tire inflator lever for an
appropriate period of time and release the lever.
Check pressure gauge and repeat the
procedure until correct pressure level is
achieved.
■To deflate:
With clip-on air chuck lever depressed, firmly
press chuck onto tire valve stem and release
lever, ensure that no air leaks. Depress the tire
inflator lever half way (until air can be heard to
be escaping) for an appropriate period of time
and release the lever. Check pressure gauge
and repeat the procedure until correct
pressure level is achieved.
Safety
■Never exceed the maximum pressure of the
tire.
■Check that the hose and chuck are in good
condition with no damage or cracks.
■Ensure safe working environment when using
compressed air.
■Return to authorized service agent for repair
and maintenance.

3
Battery Change
This inator requires 2 x AAA batteries. If the
voltage of the batteries fall below 2.6 volts, the
battery icon will ash continuously until it shuts
down. If the voltage of the batteries fall below
1. Remove the impact bumper by pulling it up
from the inator base.
2. Slide battery cap up.
Replace batteries noting polarity
marks (+ or -).
3. Replace the battery cap.
4. Replace impact bumper by pushing over
inator housing making sure to put locating
lugs back into the correct position.
WARNING
To avoid the risk of personal injury, especially to the eyes, face or skin, DO NOT direct the
air stream at any person, or any part of the body. This equipment is not intended for use by
children without adult supervision. The manufacturer reserves the right to change product
features at any time without notice.
2.5 volts, the low “LO” battery icon appears
while the power is on and then shuts down
automatically. The batteries must be changed if
the battery icon ashes.

4
Distributed by
ESCO - Equipment Supply Co.
15270 Flight Path Drive, Brooksville FL, 34604
[email protected]
SPECIFICATIONS
Description Digital Automatic Tire Inflator
Type of Inator Digital
Reader unit Digital with backlit display
Chuck type Clip on
Chuck style Single straight
Scale 0-12bar, 0-174psi, 0-1200kPa, 0-12kgF
Inlet size ¼” female
Hose length 500mm with swivel (19.7”)
Dimensions 235 L x 90 W x 110 Hmm (9.25” L x 3.5” W x 4.3” H)
Weight 0.68 kg (1.5 lbs)
Accuracy +/- 2psi @ 25-75 psi.
Operation Inate, deate, measure
Supply pressure max. 200psi, 1375kPa
Max. ination 174psi
Powered by 2 x AAA Batteries (included)
Battery life (continuous use) 80 hours
Ination ow 1200 L/min @ 1375Kpa(42.4cfm @ 200psi)
IP rating IP44
Auto OFF 90 seconds
Auto ON Upon air pressure sensing
Advised application Industrial, workshops
ALLOWABLE TOLERANCE
BAR
±0.08 up to and including 4 bar
±0.16 between 4 bar and 10 bar inclusive
±0.25 greater than 10 bar
psi
+/-1.2 up to and including 58 psi
+/-2.3 between 58 and 145 psi inclusive
+/-3.6 greater than 145 psi
TEST RESULTS
Reference pressure
BAR PSI
Display pressure
BAR PSI
Calibration Certificate
This Digital Automatic Tire Inflator has been
calib rated in its normal working position on test
equipment with an accuracy that is traceable to
International Standards according to: 86/217/EEC.
Serial Number:
Date:
www.esco.net
For more information contact Customer Service
at 1-800-352-9852