EtherWAN EX77900 Series User manual

W70G-EX77900Q5 Page 1
Copyright 2022 EtherWAN Systems, Inc. All Rights Reserved 12/01/2022
Installation Guide
EX77900 Series | Hardened Managed Ethernet Switch
Unpacking
Open the carton and unpack the items. Your package should include:
▪EX77900 hardened managed Ethernet switch
▪2 Mounting brackets
▪12 Mounting screws
▪1 Console cable
▪2 Power cables (if no terminal block)
If any items are missing or damaged, notify your EtherWAN representative. If
possible, save the carton and packing material in case you need to ship or store the
switch in the future.
What Else You Need
▪Category 5e or better cable for RJ-45 ports
▪Appropriate fiber cables for fiber ports
▪Appropriate SFP cable and modules for SFP ports
▪Personal computer with a DB-9 male interface (if switch is to be managed
through console port)
Select a Location
▪Installation: Rack-mount. Use the enclosed screws and brackets to mount
the switch in an open or enclosed 19” rack.
▪Identify a power source within 6 feet (1.8 meters).
▪Choose a dry area with ambient temperature between -40 and 75ºC (-
▪40 and 167ºF).
▪Keep away from heat sources, sunlight, warm air exhausts, hot-air vents,
and heaters.
▪Be sure there is adequate airflow.
Connect to the Data Ports
The EX77900 has the following ports:
▪24 10/100/1000 Mbps copper ports
▪8 SFP slots shared with ports 17 –24 supporting 100Mbps or 1Gbps
▪4 SFP+ slots, supporting 10Gbps or 1Gbps
10/100/1000BASE-TX Ports
Ports 1 to 16 are gigabit copper ports and can be connected to routers, other
switches, or end devices. Use category 5e or higher UTP/STP cable.
1 Gbps Combo/SFP Ports
Ports 17 –24 are combo ports, and have two physical interfaces for each port.
These ports can be used as either 10/100/1000BASE-TX on the left section or
1000BASE-FX on the right section. These ports operate in “either/or” fashion, i.e.,
connecting to fiber port 17 will render copper port 17 inoperable.
SFP+ Slots
SFP transceivers can be installed directly into right-side ports 17 –24 and SFP
ports 1 –4. Ensure that the same type of transceiver is used at both ends of the
link and that the correct type of fiber cable is used.
Connect Power
Terminal Block
If your EX77900 comes with power cables, connect the cables into the power
modules at the back of the switch. If your switch comes with a terminal block (no
cable), then connect the switch to a suitable power supply using 12 to 24 AWG
wire.
Redundant power supply is supported. However, only one power input is
required to operate the switch.
Relay Output Alarm
The switch provides relay output contacts for signaling of a user-defined power or
port failure. The relay output can be connected to an alarm signaling device.
Normal state: 3 & 2 open, 2 & 1 closed
Alarm state: 3 & 2 closed, 2 & 1 open
Power-Up Sequence
When the switch is powered up:
▪All Link/ACT LEDs blink momentarily.
▪The Power 1, 2 LEDs light up and stay lit.
▪LEDs for every port connected to a device will flash, as the switch conducts a
brief Power On Self-Test (POST).
Front Panel LEDs
LED Panel Layout
Green LED ON = network connection established
FLASHING = Port sending or receiving data
Console Configuration
Connect to the switch console by connecting the DB-9 cable to the console port of
the switch and to the serial port of the computer running a terminal emulation
application (such as HyperTerminal or Putty).
Configuration settings of the terminal-emulation program: Baud rate:
115,200bps, Data bits: 8, Parity: none, Stop bit: 1, Flow control: none.
The default login name is “root,” no password.
Web Configuration
Log in to the switch by launching a web browser and entering 192.168.1.10 in the
address bar. Enter the default login ID: root (no password) and click “Login.”
Copy Configuration to USB
The switch is equipped with one USB port (Type A connector) for configuration
file and syslog backup. The USB port can be used to save the configuration and
Syslog to a (FAT32) USB storage device.
Plug the device into the USB port, and use the “Save Configuration” command in
the web interface, or “copy running-config startupconfig” in the CLI.

W70G-EX77900Q5 Page 2
Copyright 2022 EtherWAN Systems, Inc. All Rights Reserved 12/01/2022
Installation Guide
EX77900 Series | Hardened Managed Ethernet Switch
Other Information
The power cord must be connected to a properly earth grounded outlet.
Rack Mount Instructions - The following or similar rack-mount instructions are
included with the installation instructions:
(A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that
the amount of air flow required for safe operation of the equipment is not
compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g. use of power strips).
▪The socket-outlet shall be installed near the equipment and shall be easily
accessible.
▪Do not disable the power cord grounding plug. The grounding plug is an
important safety feature.
▪Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
This equipment is intended to be used in a restricted access location and be used
by a qualified person.
Caution:
This equipment shall be used with all power supplies connected simultaneously.
Hazardous voltages may occur within this unit when connected to all power
supplies. Prevent access to hazardous voltages by disconnecting this equipment
from all power supplies.
This equipment must be connected to Protective earthing (PE) to AC mains
ground. The protective earthing conductor shall be minimum 18 AWG and having
green-and-yellow insulation. The thread diameter of screw type terminal shall be
minimum 3.5mm.
This equipment is not suitable for use in locations where children are likely to be
present.
The power cord shall be IEC 60227 certified, rated 0.75 mm2 x 3C or UL
recognized minimum 18AWG
Mains circuit connection:
DC Terminal Block
AC Terminal Block
All power connection wiring by a qualified electrician in accordance with National
Electrical Code, ANSI/NFPA 70 and Canadian Electrical Code, Part I, CSA C22.1. An
IEC certified or UL listed single-phase type circuit-breaker, rated maximum 20A,
shall be installed between mains circuit and equipment.
Thumbscrews should be tightened with a tool after both initial installation
subsequent access to the panel.
Caution:
This equipment has a connection between the earthed conductor of the DC
supply circuit and the earthing conductor. All of the following installation
conditions must be met.
▪This equipment shall be connected directly to the DC supply system earthing
electrode conductor or to a bonding jumper from an earthing terminal bar
or bus to which the DC supply system earthing electrode is connected.
▪This equipment shall be located in the same immediate area (such as
adjacent cabinets) as any other equipment that has a connection between
the earthed conductor of the same DC supply circuit and the earthing
conductor, and also the point of earthing of the DC system. The DC system
shall not be earthed elsewhere.
▪The DC supply source is to be located within the same premises as this
equipment.
▪There shall be no switching or disconnecting devices in the earthed circuit
conductor between the DC source and the point of connection on the
earthing electrode conductor.
Note: This equipment must use UL recognized Laser Class 1 optical transceiver.
This equipment is intended to be used in a restricted access location and be used
by a qualified person.
This equipment is not suitable for use in locations where children are likely to be
present.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
Protective
Earthing (PE)