EVERSPRING AN128 User manual

AN128 ON/OFF MODULE
This plug-in On/Off Module is a transceiver which is a Z-WaveTM enabled device
and is fully compatible with any Z-WaveTM enabled network. Z-WaveTM enabled
devices displaying the Z-WaveTM logo can also be used with it regardless of the
manufacturer, and ours can also be used in other manufacturer’s Z-WaveTM
enabled networks. Remote On/Off control of the connected load is possible with
other manufacturer’s Wireless Controller. Each module is designed to act as a
repeater. Repeaters will re-transmit the RF signal to ensure that the signal is
received by its intended destination by routing the signal around obstacles and
radio dead spots.
Adding to Z-WaveTM Network
In the front casing, there is an On/Off knob which is used to carry out inclusion,
exclusion or association. Put a Z-WaveTM Wireless Controller into
inclusion/exclusion mode, press the On/Off knob on the module to complete the
inclusion/exclusion process.
Function
Description
Inclusion 1. Put the Z-Wave Controller into inclusion mode.
2. Press the On/Off/Dim knob once to enter inclusion mode.
Exclusion 1. Put the Z-Wave Controller into exclusion mode.
2. Press the On/Off/Dim knob once to enter exclusion mode.
3. Node ID has been excluded.
Association 1. Operate the Z-Wave Controller to start association process.
2. Press the On/Off/Dim knob once to execute association.
Installation
1. Plug this On/Off Module into a wall outlet near the load to be controlled.
2. Plug the appliances into the On/Off Module. There are two outlets at different
sides of AN128. The appliances plugged into the controllable outlet can be
controlled by the On/Off knob and remote controller, the other side is
non-controlled and acts as a pass-through outlet. Make sure the total load of
both sides cannot exceed 1500 watts which means if the load of controllable
outlet is changed, the other side will be altered accordingly. For instance, if the
load of controllable outlet is about 1500 watts, the other should be 0 watt; while
if the load of controllable outlet is 1200 watts, the other should be 300 watts.
3. Turn the knob or switch on the load to the ON position.
4. To manually turn ON the AN128 On/Off Module, press and release the On/Off
knob. The red indicator LED will turn ON, and the load plugged into the AN128
On/Off Module will also turn ON.
5. To manually turn OFF the AN128 On/Off Module, simply press and release the
On/Off knob. The red indicator LED will turn OFF and the load plugged into the
AN128 On/Off Module will also turn OFF.
Programming
The On/Off knob allows the user
- Turn on or off the load attached
- Include or exclude the module from the Z-WaveTM system
- Control other Z-WaveTM enabled devices
Advanced Operation:
As long as any Z-WaveTM enabled device that can send below mentioned alarm
command
(ALARM_REPORT, Alarm Type == 0x01, Alarm Level == 0x11)
to the AN128 ON/OFF Module will enable its red indicator LED and the load
plugged into the AN128 ON/OFF Module to be on and off intermittently for 10
seconds.
Troubleshooting
Symptom
Cause of Failure
Recommendation
The Module not working and
LED off
1. The Module is not
plugged into the
electrical outlet
properly
2. The Module break
down
1. Check power connections
2. Don’t open up the Module and
send it for repair.
The Module LED illuminating,
but cannot control the ON/OFF
Switch of the load attached
Check if the load plugged
into the Module has its
own ON/OFF switch
Set the ON/OFF switch of the
load attached to ON
The Module LED illuminating,
but the Detector cannot control
the Module
1. Not carry out
association
2. Frequency interference
1. Carry out association
2. Wait for a while to re-try
On /Off knob
Controllable outlet
Pass-through outlet

Specification
Operating Voltage
120V/60Hz
Maximum Load
1500W
Range
Minimum 100 feet line of sight
Frequency Range
908.42 MHz
FCC ID
FU5TR003-01
* Specifications are subject to change without notice. A501111258R02
Compatible Devices
The Everspring AN128 ON/Off module is fully Z-WaveTM device compatible.
Homeowners with existing Z-WaveTM devices can easily add this device or more in
to complete a safety network firmly. The following Everspring devices are
compatible with AN128 On/Off module.
The following modules (sold separately) can be compatible with this device:
SP103 SM103 ST812 ST814 ST815
PIR Detector Door/Windows Floor Temperature/Humidity Illuminatinon
Detector Detector Detector Detector
IMPORTANT! To ensure better compatibility, only
purchase Everspring or other
manufactures’Z-WaveTM Enabled devices.
Mobile of end product
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health
and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to
take back your old appliance for disposal at least for free of charge.