Expolite TourLED 28 MKIII User manual

User Manual
TourLED 28
MKIII

FOCON SHOWTECHNIC
Vertriebsgesellschaft mbH
Teichweg 4+6
D-49504 Lotte/Wersen
Telefon: [phone]
Fax: [phone]
[email protected]
www.focon-showtechnic.com
by
The enclosed General Informations for Expolite
Units are part of these user manual. Read them
carefully before operating the device.

Content
Inhalt - Content
Page
Delivery
Product Information
Dimensions
Installation
Operation
Using DMX512 Controler
E-04
E-05
E-06
E-07
E-08
E-13
ENG

Delivery
- Expolite TourLed 28 Pro Zoom CM+W MKIII
Expolite units are checked before shipping. If items are missing, please
contact your Expolite distributor
- Displaycover
- Powercord
- General Information for Expolite Units
- User Manual
E-04

Specifications
Voltage
Powerconsumption
Weight
Temperature
Dimensions
Humidity*
IP rated
Housing
LED´s
Angle
Control
DMX-Channels
Connectors
100V - 240V AC 50/60Hz
128W
334 x 191 x 236 mm
6.6 kg
Power In/Out | DMX In/Out
-20°C - 45°C
< 80%
IP 65
Die-cast aluminium, black
7 x 20W 4in1 RGBW
8°- 40°
Stand-Alone / Master-Slave / DMX512
3 - 25 (3/4/5/6/7/12/17/25)
* See general information for Expolite Units - Condensation inside Housing
E-05
40°
5
5
4
3
2
1
0
1
2
3
4
0.73 2.18 3.64 5.10 7.28
1 3 5 7 10
78250
10000
8694
1111
3130
400
1597
204
783
100
0.14 0.42 0.70 0.98 1.40
8°
40°
8°
40°
8°
Art.No.: led28426

Dimensions
E-06
236

DMX512
CONTROLLER
............
DMX Addr.1 DMX Addr.(Nx1)+1 DMX Addr.(Nx2)+1
E-07

Display Panel operation
Menumap
MENU:
ENTER:
UP:
DOWN:
ENTER UP DOWN
MENU
Back
Enter or Save
Up
Down
PR.01
PR.02
PR.10
RUN DMX
SLAV
SC.01
SC.02
SC.30
AT.01
AT.02
AT.10
AUTO
PR.01
PR.02
PR.10
D.(001~512)
DMX
R.(0~255)
G.(0~255)
B.(0~255)
S.(0~20)
T.(0~255)
F.(0~255)
MENU
R.(0~255)
G.(0~255)
B.(0~255)
W.(0~255)
STAT
EDIT
OFF
RGBW
COLO
SET UPLD
REST
DIM1
DIM3
DIM2
DIM4
DIM
UC
OF F
RGB
PERS
CV1
CV3
CV2
OFF
CURV
BLAK
SAVE
DERR
ST.(0~20)
W.(0~255)
TR16
8BIT
AR2.D
AR2.S
TOUR
16BI
ARC.2
RGBW
AR1.D
SLCK
STRB
ON
OFF
CLAS
SPEC
SSP
KEY ON
OFF
CAL
WT.0 1
CAL1
****
WT.11
CALR **** OKCALR
RGBW
R(0~255)
G(0~255)
B(0~255)
CAL2
R(0~255)
G(0~255)
B(0~255)
W(0~255)
INFO VERS V01
Display operation
E-08

Edit static color
MENU
R.(0~255)
G.(0~255)
B.(0~255)
W.(0~255)
STAT
ST.(0~20)
In the Menu „STAT“ values of each function for Stand-Alone operation can be set.
Set and combine the range (0-255) for Red, Green, Blue, White an Zoom for 0-100%,
also Strobe for 0-20Hz.
MENU
AT.01
AT.02
AT.10
AUTO
PR.01
PR.02
PR.10
Activate auto programs
In the Menu „AUTO“ pre-programmed programs can be activatet.
The programs „AT01" to „AT10" can not be edited. The programs „PR01" to „PR10" are editable.
For further explanation see „Edit custom programs“
Autoprograms will be send to connected devices. For the
Master-Slave operation Signals will be send via DMX-Cable. This may cause disturbence on
other devices.
Run mode
MENU
RUN DMX
SLAV
In the Menu „Run“ the Run-mode will be set.. For operation with a DMX-controller
select „DMX“. For use as Slave select „SLAV“.
In Slave-mode the unit recives static color or auto-program from the master-unit.
MENU
D.(001~512)
DMX
Set DMX-Adress
Set the DMX-Adress of the unit in the „DMX“ menu.
E-09

Personality
In the Menu „PERS“ the DMX-Personality will be set. Choose and select
the personality.
Benutzerprogramme editieren
In the Manu „EDIT“ custom auto programms „PR01" to „PR10" can be edited.
Each program has 30 steps that can be edited. Each step contains the values
for RGBW, Zoom, Strobe (0-20Hz), step-time and fade-time.
Custom programs can be uploaded from a master-device. See „special settings“
Special settings
„KEY“: enables(ON) or disables(OFF) automatic lock-out with password-protection.
Password to re-enter is „UP“-“DOWN“-“UP“-“DOWN“-“ENTER“ and can`t be changed.
„UPLD“: Select to upload custom-programs from a master-device.
Run-mode needs to be set to „SLAVE“
„REST“: Triggers factory-reset.
E-10

„COLO“: In the Menu Color the color-kalibration can be selected or deactivated. If „RGBW“
is selected the maximum DMX-value (255) will be limited to the stored value in „CAL2".
If „UC“ (Uniform-Color) is selected the factory-calibration will be used. RGBW output is balanced
to differend generations of units. If „OFF“ is selected the calibration is disabled. RGBW reaches
maximum power without limit by calibration.
„DIM“: Different dimming-speeds can be selected from fast (DIM1) to slow (DIM4).
DIM4 acts as halogen-simulation.
„CURV“: In the Curve-menu different dimming-curves,as shown below, can be selected.
CURV dimming
1: OFF
2: Cv1
3: CV3
4: Cv4
1
2
3
4
(100 %)
„DERR“: Select reaktion of losing DMX signal. Select „SAVE“ to keep the last recived signal
or „BLAK“ to change to blackout.
„SLCK“: Enable or disable password-protection for „SET“-menu. If „ON“ is slected the user
needs to enter the password (UP+DOWN+UP+DOWN) to enter the „SET“-menu. „OFF“
disables password-protection.
„ZOOM“: Calibrates the position of POS1 and POS2. Set position to 0 for smallest position.
„BASE“ calibrates to default zoom-position.
E-11

Calibration and whitebalance
MENU
CAL
WT.01
CAL1
****
WT.11
CALR **** OKCALR
RGBW
R(0~255)
G(0~255)
B(0~255)
CAL2
R(0~255)
G(0~255)
B(0~255)
W(0~255)
Password „UP“-“DOWN“-“UP“-“DOWN“
„CAL1" select WH.01 to WH.1 to calibrate the pre-programmed whitecolors.
RGBW is used to mix pre-programmed colors.
„CAL2" adjusts the output when the DMX-controller sends 255 on RGBW.
„CALR“ sets all calibrations to factory-default.
Zoom range
In the menu „ZOOM“ the limit of the zoom-chanenl can be edited.
If using a DMX-controller you are only able to access to the range between „POS1" and „POS2".
E-12

Using DMX512
E-13
This unit has different DMX-Personalities with different amount of DMX-channels.
10 DMX-Personalities with 3, 4, 5, 6, 7, 12, 17 und 25 channels are available.
CHANNEL ASSIGNMENT

E-14

E-15

E-16

E-17

E-18

E-19

E-20