FAAC 844 ER 3PH User manual

844 ER 3PH
Translation of the original instructions

FAAC S.p.A. Soc. Unipersonale
Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Tel. [phone] - Fax [phone]
www.faac.it - www.faacgroup.com
© Copyright FAAC S.p.A. dal 2020. Tutti i diritti riservati.
Nessuna parte di questo manuale può essere riprodotta, archiviata, distribuita a terzi
né altrimenti copiata, in qualsiasi formato e con qualsiasi mezzo, sia esso elettronico,
meccanico o tramite fotocopia, senza il preventivo consenso scritto di FAAC S.p.A.
Tutti i nomi e i marchi citati sono di proprietà dei rispettivi fabbricanti.
I clienti possono effettuare copie per esclusivo utilizzo proprio.
Questo manuale è stato pubblicato nel 2020.
© Copyright FAAC S.p.A. from 2020. All rights reserved.
No part of this manual may be reproduced, archived, distributed to third parties nor
copied in any other way, in any format and with any means, be it electronic, mechanical
or by photocopying, without prior written authorisation by FAAC S.p.A.
All names and trademarks mentioned are the property of their respective manu-
facturers.
Customers may make copies exclusively for their own use.
This manual was published in 2020.
© Copyright FAAC S.p.A. depuis 2020. Tous droits réservés.
Aucune partie de ce manuel ne peut être reproduite, archivée ou distribuée à des tiers
ni copiée, sous tout format et avec tout moyen, qu’il soit électronique, mécanique ou
par photocopie, sans le consentement écrit préalable de FAAC S.p.A.
Tous les noms et les marques cités sont la propriété de leurs fabricants respectifs.
Les clients peuvent faire des copies pour leur usage exclusif.
Ce manuel a été publié en 2020.
© Copyright FAAC S.p.A. ab dem 2020. Alle Rechte vorbehalten.
Kein Teil dieses Handbuchs darf reproduziert, gespeichert, an Dritte weitergegeben
oder sonst auf eine beliebige Art in einem beliebigen Format und mit beliebigen
Mitteln kopiert werden, weder mit elektronischen, noch mechanischen oder durch
Fotokopieren, ohne die Genehmigung von FAAC S.p.A.
Alle erwähnten Namen und Marken sind Eigentum der jeweiligen Hersteller.
Die Kunden dürfen nur für den Eigengebrauch Kopien anfertigen.
Dieses Handbuch wurde 2020 veröffentlicht.
© Copyright FAAC S.p.A. del 2020. Todos los derechos están reservados.
No puede reproducirse, archivarse, distribuirse a terceros ni copiarse de ningún modo,
ninguna parte de este manual, con medios mecánicos o mediante fotocopia, sin el
permiso previo por escrito de FAAC S.p.A.
Todos los nombre y las marcas citadas son de propiedad de los respectivos fabricantes.
Los clientes pueden realizar copias para su uso exclusivo.
Este manual se ha publicado en 2020.
© Copyright FAAC S.p.A. van 2020. Alle rechten voorbehouden.
Niets uit deze handleiding mag gereproduceerd, gearchiveerd, aan derden openbaar
gemaakt of op andere wijze gekopieerd worden, in om het even welke vorm en
met geen enkel middel, noch elektronisch, mechanisch of via fotokopiëren, zonder
schrfitelijke toestemming vooraf van FAAC S.p.A.
Alle vermelde namen en merken zijn eigendom van de respectievelijke fabrikanten.
De klanten mogen kopieën maken die enkel voor eigen gebruik bestemd zijn.
Dez handleiding werd in 2020 gepubliceerd.

844 ER 3PH 1 532366 - Rev.A
Translation of the original instructions ENGLISH
EU DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares on his sole responsibility that the following products:
Description: Gearmotor for sliding gates
Models: 844 ER 3PH
comply with the following applicable EU legislations:
2014/30/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
Bologna, Italy, 01-07-2020 CEO
A. Marcellan
DECLARATION OF INCORPORATION FOR PARTLY
COMPLETED MACHINERY
(2006/42/EC ANNEX II P.1, B)
Manufacturer and person authorised to prepare the relevant technical documentation
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares that for the partly completed machinery:
Description: Gearmotors for sliding gates
Model: 844 ER 3PH
The essential requirements of the Machinery Directive 2006/42/EC (including
all applicable amendments) that have been applied and fulfilled are as follows:
1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.1,
1.3.2, 1.3.4, 1.3.6, 1.3.9, 1.4.1, 1.4.2.1, 1.5.1, 1.5.2,
1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.5.10, 1.5.11, 1.6.1, 1.6.4,
1.7.1, 1.7.2, 1.7.3, 1.7.4.2, 1.7.4.3
and that the relevant technical documentation has been compiled in compliance
with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN12100:2010
EN13849-1:2015 CAT.2 PL “C
EN13849-2:2012
Other standards applied: EN 60335-1:2012+A11:2014+A13:2017
EN 60335-2-103:2015
And also undertakes to transmit, in response to a reasoned request by the national au-
thorities, relevant information on the partly completed machinery by mail or e-mail.
Finally, the manufacturer declares that the above-mentioned partly completed
machinery must not be put into service until the final machine in which it is to be
incorporated has been declared compliant with the requirements of the above-
mentioned Machinery Directive 2006/42/EC.
Bologna, Italy, 01-07-2020 CEO
A. Marcellan

844 ER 3PH 2 532366 - Rev.A
Translation of the original instructions ENGLISH
TABLES
 1 Technical data ..................................................... 7
 2 Scheduled maintenance ........................................24
CONTENTS
EU Declaration of conformity ................................... 1
Declaration of incorporation for partly completed machinery 1
1. INTRODUCTION TO THIS INSTRUCTION MANUAL .......... 3
1.1 Meaning of the symbols used ................................... 3
2. SAFETY RECOMMENDATIONS .................................. 4
2.1 Installer safety .................................................... 4
2.2 Transport and storage ............................................ 4
2.3 Unpacking and handling ........................................ 5
Vent closure ....................................................... 5
2.4 Disposal of the product ......................................... 5
3. 844 ER 3PH .......................................................... 6
3.1 Intended use ...................................................... 6
3.2 Limitations of use ................................................. 6
3.3 Unauthorised use ................................................. 6
3.4 Emergency use .................................................... 6
3.5 Product identification ............................................ 7
Product warnings ................................................. 7
3.6 Technical specifications .......................................... 7
3.7 Component identification ....................................... 8
Components supplied ........................................... 8
Components supplied separately............................... 8
3.8 Dimensions ........................................................ 9
3.9 Manual operation................................................. 9
Releasing the gearmotor ........................................ 9
Restoring operation .............................................. 9
4. INSTALLATION REQUIREMENTS ............................... 10
4.1 Mechanical requirements ....................................... 10
4.2 Electrical system ................................................. 10
4.3 Example system.................................................. 11
4.4 Installation dimensions ......................................... 12
5. MECHANICAL INSTALLATION .................................. 13
Tools required .................................................... 13
5.1 Replacing the spring (for leaves weighing more than 1000
kg) ...................................................................... 13
5.2 Installing the foundation plate ................................. 14
5.3 Installing the pinion ............................................. 14
5.4 Installing the gearmotor ........................................ 15
Open the vent hole .............................................. 15
5.5 Installing the rack ................................................ 16
Steel rack - Weld-on fastenings ................................ 16
Steel rack - Screw-on fastenings ............................... 17
5.6 Adjusting and checking ......................................... 18
5.7 Fastening the gearmotor permanently ....................... 18
6. OPTIONAL EQUIPMENT ......................................... 19
6.1 Release lock with personalised key ............................ 19
7. START-UP........................................................... 20
7.1 Electrical connections ........................................... 20
7.2 Earthing the gearmotor ......................................... 20
7.3 Installing the cable glands ...................................... 20
7.4 Installing the end of travel plates .............................. 21
7.5 Starting the automation ........................................ 22
7.6 Adjusting the anti-crushing system ........................... 22
Limiting the static force ......................................... 22
Obstacle detection .............................................. 22
8. PUTTING INTO SERVICE ......................................... 23
8.1 Final checks ...................................................... 23
8.2 Installing the casing ............................................. 23
8.3 Final operations .................................................. 23
9. MAINTENANCE .................................................... 24
9.1 Routine maintenance ........................................... 24
10. INSTRUCTIONS FOR USE ...................................... 25
10.1 Safety recommendations...................................... 25
10.2 Emergency use ................................................. 26
10.3 Manual operation .............................................. 26
Releasing the gearmotor ....................................... 26
Restoring operation ............................................. 26

844 ER 3PH 3 532366 - Rev.A
Translation of the original instructions ENGLISH
1. INTRODUCTION TO THIS INSTRUCTION MANUAL
This manual provides the correct procedures and requirements for
installing 844 ER 3PH and maintaining it in a safe condition.
When drafting the manual, the results of the risk assessment con-
ducted by FAAC S.p.A. on the entire product life cycle have been taken
into account in order to implement effective risk reduction measures.
The following stages of the life cycle of the product have been con-
sidered:
-Delivery/handling
-Assembly and installation
-Set-up and commissioning
-Operation
-Maintenance/troubleshooting
-Disposal at the end of the product’s life cycle
Risks arising from installation and using the product have been taken
into consideration; these include:
-Risks for the installation/maintenance technician (technical
personnel)
-Risks for the user of the automation system
-Risks to product integrity (damage)
In Europe, the automation of a gate falls under the Machinery Directive
2006/42/EC and the corresponding harmonised standards. Anyone
automating a gate (new or existing) is classified as the Manufacturer
of the Machine. They are therefore required by law, among other
things, to carry out a risk analysis of the machine (automatic gate in
its entirety) and take protective measures to fulfil the essential safety
requirements specified in Annex I of the Machinery Directive.
FAAC S.p.A. recommends that you always comply with the EN 12453
standard and in particular that you adopt the safety criteria and de-
vices indicated, without exception, including the dead-man function.
This manual also contains general information and guidelines, which
are purely illustrative and not exhaustive, in order to facilitate the ac-
tivities carried out by the Manufacturer of the Machine in all respects
with regard to carrying out the risk analysis and drafting the instruc-
tions for use and maintenance of the machine. It should be clearly
understood that FAAC S.p.A. accepts no liability for the reliability and/
or completeness of the above instructions. As such, the manufactu-
rer of the machine must carry out all the activities required by the
Machinery Directive and the corresponding harmonised standards
on the basis of the actual condition of the locations and structures
where the product 844 ER 3PH will be installed, prior to commissio-
ning the machine. These activities include the analysis of all the risks
associated with the machine and subsequent implementation of all
safety measures intended to fulfil the essential safety requirements.
This manual contains references to European standards. The au-
tomation of a gate must fully comply with any laws, standards and
regulations applicable in the country where installation will take place.
L Unless otherwise specified, the measurements provided in the instructions
are in mm.
NOTES AND WARNINGS ON THE INSTRUCTIONS
FWARNING ELECTRIC SHOCK HAZARD - The operation or step described must
be carried out following the instructions provided and according to the safety
regulations.
!WARNING, personal injury hazard or risk of damage to components - The
operation or step described must be carried out following the instructions
provided and according to the safety regulations.
LWARNING - Details and specifications which must be respected in order to
ensure that the system operates correctly.
RECYCLING AND DISPOSAL - The materials used in manufacturing, the batteries
and any electronic components must not be sent to landfill. They must be
taken to authorised recycling and disposal centres.
FIGURE E.g. 1-3 see Figure 1 - item 3.
TABLE E.g. 1 see Table 1.
§ CHAPTER/SECTION E.g. §1.1 see Section 1.1.


STATUS OF THE LEDS ON THE BOARD
 LED off  LED on  LED flashing
SAFETY SIGNS AND SYMBOLS
GENERIC HAZARD
Personal injury hazard or risk of damage to components.
ELECTROCUTION HAZARD
Risk of electric shock from live parts.
CRUSHING HAZARD
Risk of crushing to the hands/feet due to the presence of
heavy parts.
CUTTING/AMPUTATION/PUNCTURE HAZARD
Cutting hazard due to the presence of sharp components or the
use of pointed/sharp tools (drill).
SHEARING/TRAPPING HAZARD
Risk of fingers and hands being sheared or trapped due to
moving parts.
BURNING OR SCALDING HAZARD
Risk of burns due to the presence of high-temperature parts.
PERSONAL PROTECTIVE EQUIPMENT
Personal protective equipment must be worn to protect against hazards (e.g. crushing,
cutting, shearing etc.):
Obligation to wear mask/goggles to protect the eyes from the risk of frag-
ments due to the use of drill or welder.
Obligation to wear work gloves.
Obligation to wear safety footwear.
1.1 MEANING OF THE SYMBOLS USED

844 ER 3PH 4 532366 - Rev.A
Translation of the original instructions ENGLISH
2. SAFETY RECOMMENDATIONS
2.1 INSTALLER SAFETY
2.2 TRANSPORT AND STORAGE
! Follow the instructions on the package
WARNINGS ON PACKAGING
Handle with care. Presence of fragile parts.
Up indication.
Keep away from water and moisture.
3
Maximum number of stacked packages.
CE marking.
PALLETISED SUPPLY
RISKS
PERSONAL PROTECTIVE EQUIPMENT
SINGLE PACKAGE
RISKS
PERSONAL PROTECTIVE EQUIPMENT
Store the product in its original packaging, in closed and dry premises,
protected from the sun and free from dust and aggressive substances.
Protect from mechanical stress. If stored for more than 3 months,
regularly check the condition of the components and the packaging.
-Storage temperature: 5°C to 30°C.
-Percentage of humidity: 30% to 70%.
This product is placed onto the market as “partly completed machin-
ery”, therefore it cannot be commissioned until the machine in which
it has been incorporated has been identified and declared to conform
to the Machinery Directive 2006/42/EC by the actual Manufacturer.
! Incorrect installation and/or incorrect use of the product might cause serious
harm to people. Read and comply with all the instructions before starting
any activity on the product. Keep these instructions for future reference.
Perform installation and other activities adhering to the sequences provided
in the instructions manual.
Always comply with all the requirements contained in the instructions and
warning tables at the beginning of the paragraphs. Always comply with
the safety recommendations.
Only the installer and/or maintenance technician is authorised to work on
the automation components. Do not modify the original components in
any way.
Close off the work site (even temporarily) and prevent access/transit. EC
countries must comply with the legislation that transposes the European
Construction Site Directive 92/57/EC.
The installer is responsible for the installation/testing of the automa-
tion and for completing the Register of the system.
The installer must prove or declare to possess technical and profes-
sional proficiency to perform installation, testing and maintenance
activities according to the requirements in these instructions.
Installation activities require special work conditions to reduce to the
minimum the risks of accidents and serious damage. Furthermore,
the suitable precautions must be taken to prevent risks of injury to
persons or damage.
! The installer must be in good physical and mental condition, aware of and
responsible for the hazards that may be generated when using the product.
The work area must be kept tidy and must not be left unattended.
Do not wear clothes or accessories (scarves, bracelets, etc.) that may get
caught in moving parts.
Always wear the personal protective equipment recommended for the type
of activity to be carried out.
The required level of workplace lighting must be equal to at least 200 lux.
Operate CE marked machinery and equipment in compliance with the
manufacturer's instructions. Use work instruments in good conditions.
Use the transport and lifting equipment recommended in the instructions
manual.
Use safety-compliant portable ladders of adequate size, fitted with anti-slip
devices at the top and bottom, equipped with retainer hooks.
! Follow the instructions on the packaging
during handling.
Use a forklift or pallet truck, following safety
regulations to avoid the risk of impacts or
collisions.
! Follow the instructions on the packaging during
handling.
For manual lifting, there should be one person for every
20 kg to be lifted.

1
2
844 ER 3PH 5 532366 - Rev.A
A
A
7
1
2
4 3
Translation of the original instructions ENGLISH
2.3 UNPACKING AND HANDLING
RISKS
PERSONAL PROTECTIVE EQUIPMENT
1. Open the package and remove the contents.
-Do not lift the gearmotor by the casing or the electronic
board. Grip the body of the gearmotor using the handholds A
(1).
2. Check that all components are present and intact (See § Compo-
nent identification).
! The packaging materials (plastic, polystyrene etc.) must not be left within
reach of children as they are potential sources of danger.
When you have finished with them, dispose of the packaging in the appropri-
ate containers, as per applicable waste disposal regulations.
VENT CLOSURE
! The 844 ER 3PH is supplied with the vent hole closed with a screw and washer
(2). Whenever the gearmotor is handled, the vent must be closed to
prevent oil leaking out.
1Gearmotor 844 ER 3PH
2Gearmotor bracket guards and Hardware/accessories
3Limit switches
4Instruction manual
2.4 DISPOSAL OF THE PRODUCT
After having dismantled the product, dispose of it in compliance with
the current waste disposal regulations.
Components and structural materials, batteries and electronic components
must not be disposed of together with household waste. They must be taken
to authorised disposal and recycling centres.
The oil must be gathered in a watertight container and given to an authorised
disposal and recycling centre. Do not mix with other substances such as
antifreeze or transmission fluids. Keep the used oil away from sources of
heat and out of the children's reach. The fluid is not hazardous to health. In
case of contact with eyes, skin or clothing, wash and rinse the affected parts.
The technical data sheets of the fluids are available on request.

844 ER 3PH 6 532366 - Rev.A
Translation of the original instructions ENGLISH
3.4 EMERGENCY USE
3. 844 ER 3PH
-Uses other than the intended use are prohibited.
-It is prohibited to install the automation system outside of the
limits specified in the Technical Data and Installation Require-
ments sections.
-It is forbidden to use 844 ER 3PH in a constructional configuration
other than the one provided by the manufacturer.
-No component part of the product may be modified.
-It is prohibited to install the automation system on escape routes.
-It is prohibited to install the automation system to create fire
doors.
-It is prohibited to install the automation system in environments
in which there is a risk of explosion and/or fire: the presence of
flammable gases or fumes is a serious safety hazard (the product
is not ATEX certified).
-It is prohibited to power the system with energy sources other
than those specified.
-It is prohibited to integrate commercial systems and/or
equipment other than those specified, or use them for purposes
not intended and authorised by their respective manufacturers.
-Do not allow water jets of any type or size to come into direct
contact with the gear motor.
-Do not expose the gear motor to corrosive chemicals or atmo-
spheric agents.
-It is prohibited to use and/or install accessories which have not
been specifically approved by FAAC S.p.A.
-It is prohibited to use the automation system before performing
commissioning.
-It is prohibited to use the automation system in the presence of
faults which could compromise safety.
-It is prohibited to use the automation system with the fixed and/
or mobile guards removed or altered.
-Do not use the automation system unless the area of operation
is free of persons, animals or objects.
-Do not enter/remain in the area of operation of the automation
system while it is moving.
-Do not try to prevent the movement of the automation system.
-Do not climb on, hold onto or let yourself be pulled by the
leaf. Do not climb onto the gear motor.
-Do not allow children to approach or play in the area of operation
of the automation system.
-Do not allow the control devices to be used by anyone who is
not specifically authorised and trained to do so.
-Do not allow the control devices to be used by children or persons
with mental and physical deficiencies unless they are supervised
by an adult who is responsible for their safety.
! During manual operation, gently guide the leaf the whole way, do not push
it and let it slide freely.
3.3 UNAUTHORISED USE3.1 INTENDED USE
The FAAC model 844 ER 3PH gearmotors have been designed to
control horizontal movement sliding gates intended for installation
in areas that are accessible to people, the main purpose of which is
to provide safe access for goods, vehicles and people to industrial,
commercial or residential buildings.
Only one gearmotor must be installed for each leaf. The system
requires a special foundation plate, supplied separately, which is
embedded in a plinth. The gate must be moved via a drive pinion and
a rack (supplied separately). The 844 ER 3PH has a built-in electronic
board, with specific instructions.
To move the gate manually, follow the instructions in section § Manual
operation.
! Any other use that is not expressly specified in these instructions is prohibited
and could affect the integrity of the product and/or represent a source of
danger.
3.2 LIMITATIONS OF USE
The maximum force required to move the leaf by hand over its entire
length of travel must be 225 N for residential areas and 260 N for
industrial or commercial areas.
The maximum force required to start the movement must be less
than the maximum torque at initial thrust of the operator indicated
in the technical data.
The leaf must fall within the dimensional and weight limits indicated
in the technical data.
The presence of weather conditions such as snow, ice and strong wind,
even occasional, could affect the correct operation of the automation,
the integrity of the components and be a potential source of danger
(see § Emergency use).
844 ER 3PH is not designed to be a security (break-in protection)
system.
If there is a pedestrian access gate integrated in the leaf of the gate,
the motorised movement must be disabled when the pedestrian gate
is not in a safe position.
The installation must be visible during the day and at night. If it is
not, appropriate solutions must be provided to make the fixed and
moving parts visible.
Implementing the automation requires the installation of the neces-
sary safety devices, identified by the installer through an appropriate
risk assessment of the installation site.
In emergencies or if there is a fault, turn off the power supply to the
automation. If the leaf can be moved safely by hand, use the MANUAL
OPERATION mode; otherwise place the automation out of service until
it has been reset/repaired.
In the case of a breakdown, the automation must be reset/repaired
exclusively by the installer/maintenance technician.

3
844 ER 3PH 7 532366 - Rev.A
0120 0001
••••••
••••••
•••• ••••
••••••
••••
••
••••••
••••••
••••••
844 ER 3PH
* REFERS TO 380 V ~ - 50Hz
FAAC S.p.A. Soc. Unipersonale
Via Calari, 10 - 40069 Zola Predosa BOLOGNA
Italy
Italy
Cod. ... MMYY PROG
Translation of the original instructions ENGLISH
3.5 PRODUCT IDENTIFICATION
The product can be identified by the plate (3).
PRODUCT WARNINGS
The adhesive sign must be placed on the casing by the installer. It indicates
the risk of trapping fingers / hands due to the rotation of the pinion.
Adhesive sign on the casing. It indicates the breather screw that must be
removed before start-up.
3.6 TECHNICAL SPECIFICATIONS
Electromechanical oil-bath gearmotor, supplied without pinion. To
choose the correct FAAC Module 4 pinion to install (Z12, Z16, Z20)
see  Technical data.
Irreversible system In order to be operated manually, the gearmotor
has to be released using the key provided.
Magnetic encoder The encoder determines the position of the leaf
and the speed of movement.
Adjustable sensitivity obstacle detection The electronic board detects the
presence of an obstacle via the encoder. If an obstacle is detected
during opening or closing, the gate reverses for 1 s and then the
automation stops.
Force limitation The maximum force exerted by the gearmotor is
adjusted by means of the mechanical twin-disk clutch in oil-bath.
Inductive limit switches To be fixed to the rack to set the opening and
closing stop positions.
End of travel slowdown Adjustable electronic slowdown near to the
open and closed positions.
Board E844 3PH The built-in electronic board is equipped with a dis-
play, programming buttons and a protective plastic cover.
Equipment required The following must be purchased:
-foundation plate
-pinion for module 4 rack
-rack module 4
 1 Technical data
844 ER 3PH
Power supply voltage 220-240 V~ 50/60 Hz
Max power 950 W
Max thrust force* 2500 N (Z12), 1900 N (Z16), 1500 N (Z20)
Max torque at initial thrust* 1650 N (Z12), 1250 N (Z16), 1000 N (Z20)
Max leaf length* 30 m (Z12), 40 m (Z16), 50 m (Z20)
Max leaf weight* 2200 kg (Z12), 1600 kg (Z16), 1000 kg (Z20)
Leaf speed* 7.1 m/min (Z12), 9.5 m/min (Z16), 12 m/min (Z20)
Stopping space* 50 mm (Z12), 65 mm (Z16), 80 mm (Z20)
Type of use Apartment complexes, Offices / Industrial
Ambient operating temperature -20 °C to +55 °C
Continuous use time (ROT) Continuous at 25°C
Protection rating IP44
Dimensions (LxDxH) 275x191x388 mm
Gearmotor weight 16 kg
Oil FAAC HP OIL
* according to the pinion used: Module 4 Z12, Z16, Z20
Sale code
Product name
Month/year of production + Progressive number
for the month of production
Example:
IDENTIFICATION NUMBER
made in:
January 2017
progressive:
0001

4
5
844 ER 3PH 8 532366 - Rev.A
12
15
17
11
14
16
3
1
7
8
9
10
13
2
(x 2)
6
54
Translation of the original instructions ENGLISH
3.7 COMPONENT IDENTIFICATION
COMPONENTS SUPPLIED
Gearmotor
1 Casing
2 Electronic board E844 3PH with protective cover
3 Limit switch sensor
4 Magnet for encoder
5 Anti-crushing clutch adjustment screw
6 Oil filler plug
7 Earth connector
8 Gearmotor body
9 Key release
10 Fastening brackets
Hardware/accessories
11 Gearmotor bracket guards
12 Cable glands to install in the board compartment
13 Dowel pin and washer for securing the Z16 and Z20 pinions, casing fastening
screws with screw caps, clutch adjustment spring (for leaves weighing more
than 1000 kg), adhesive hazard warning sign, release key. DO NOT use terminal
boards, cable lugs for the earth cable, long screw caps.
14 Pair of plates for the inductive opening and closing limit switches
COMPONENTS SUPPLIED SEPARATELY
The installation requires the following FAAC components that are
supplied separately:
15 Steel rack with spacers (to be screwed or welded on)
16 Foundation plate with mounting hardware
17 Module 4 Pinion Z20, or Z16, or Z12
DANGER, AUTOMATIC MOVEMENT warning sign