Fanvil I20-T User manual

Voice Access System I20 T Quick Installation Guide
1、Introduction

Package Contents
2、Voice Access Controller Components Description
3、Interface Description
I20-T Access Controller
Amphenol Connector
Software CD
Quick Instanllation Guide
Speaker
Mic
Intercom call
Button
Numeric Keypad(password
and dialing)
Fixed screw
Red Light: Power Indicator
Green Light: Networking and
registration status indicator
Call/Answer Indicator
Housing

3.1 Network, Power Switch, Electric Lock Connection
3.2 Electric Lock Connection Driver Option
【Notice】When the initial electric current of the lock is less than 500mA/12V, you can access
CN7
LAN（UTP Cable Connection）
1
2
3
4
5
6
4/5
7/8
TX+
TX-
RX-
RX+
CN6
Output12V DC
Electric Lock Driver
WAN（UTP Cable Connection）
1
2
3
4
5
6
7
8
9
10
11
V+
GND
NC
COM
NO
POE+
POE-
TX+
TX-
RX-
RX+
12V DC input
Normally open, normally
close port
JP1
Outside
Driver
1
2
3
4
External Power Driving
Jumper
JP1
Inside
Driver
1
2
3
4
Internal Power Driving
Jumper
CN6
CN7

to the internal driven mode and use the POE of the Voice Access System or 12V DC to
control the the switch of the electric lock ; When the initial electric current of the lock is more
than 500mA/12V, you need to access to the external driven mode(Use specialized DC
power to control the electric lock )
3.3 Wiring
Relay connection description：
NO：means idle-disconnected contact (normally open)
COM: means a pin contact(middle)；
NC：means an idle-connected contact(normally close)；
Electric lock
power supply
mode
Electric
lock
Jumper
JP1
Mode of connection
Internal
External
NO
NC
√
√
Inside
Driver
1
2
3
4
√
√
Outside
Driver
1
2
3
4
√
√
Inside
Driver
1
2
3
4

Electric lock power
supply mode
Electric
lock
Jumper
JP1
mode of connection
Interna
l
External
N
O
NC
√
√
Outside
Driver
1
2
3
4
√
√
Outside
Driver
1
2
3
4
4、Setup of Voice Access System
Step 1：Connect Network
Plug one side of a cable to the WAN socket of I20, then the connection of hardware is
finished. In most of time, you should reset your network to DHCP mode.

Step 2：Get Device IP Address
How to get IP Address：
Method 1. Use iDoorPhoneNetworkScanner tool
1）Install enclosed iDoorPhoneNetworkScanner tool;
2）Ensure the computer which installed iDoorPhoneNetworkScanner.exe is in the same network with I20
Voice Access Controller.
3）Run iDoorPhoneNetworkScanner.exe to search corresponding device’s IP address.
Method 2: Press “#”key for 5 seconds, the controller will report it IP number by itself.
Step 3: Get Voice Access SIP account via web
Use your web browser to input its IP address (example: http://192.168.1.149) The default user name
“admin”, the password is also “admin”.

VOIP Account Setting：
Set SIP server address, port, user name, password and number. Then start registration.
Step 4：Set Speed Dial Key
Setting Speed Dial to call SIP accounts, configuring DSS KEY1 corresponding Type: Hok key, Value:
number, line: the registered SIP line (the number corresponded to), subtype: Speed Dial. Then submit

Step 5：Parameters Setting
Voice Access Configuration
Setting Item
Function
Initial Value
Open Time
Time for open the door, if time is up, the
door will be closed automatically.
5s
Holding Time
After time is up, the call will be ended
automatically.
120s
Remote Openig
Time
Remote opening password.
*
Local PIN
Local password for the keypad
6789
Tone settings
Mute/Short beeps/Long beeps
Bell ringing
Keypad mod（I20T
Valid）
Password only(Prohibit
call)/Password-Dial
Dialing and password
input
Description
Displayed on iDoorPhoneNetworkScanner
software
I20 IP door phone
Remote
phonebook
settings
Enabling access phone: when remote phone
calls, input access code first then input
password to open the door.
Disabling access phonebook: when remote
Enable

phone calls, input password only.
Remote Phonebook
Number
Remote phone number
Authentication
code
Access code for visitor. When remote
phone calls, if the number is in access
list, you can input access code to open
the door.
When IP phone calls, it
needs to input
authentication code to
control voice access
controller.
Type of Host
When owner calls, controller answer
automatically, when visitor calls,
controller mute.
Name
Card holder’s name
Position
Card holder’s position
Department
Card holder’s department
Card number
RFID’s number
5、Visitor Calls, Remote Open the Door
1）Visitor presses speed-dial key to call the owner.
2）Owner answers the call and presses “*”key to open the door from visitor.
6、Owner Remote Opens the Voice Access Controller by VOIP Phone
1）Owner calls the Voice Access Controller by VOIP Terminal.
2）the Voice Access Controller answers the call automatically.
3）Owner enter Authentication code by VOIP Terminal’s keypad to open the door.
7、Card Management
7.1 Issue Card Management
（1）Issue <issue administration card>
Input available card number to ID input field, choose Issuer, then press Add to add Issue
Administration Card.
（2）Issue <Delete administration card>
Input available card number to ID input field, choose “Revocation”, then press Add to add Delete
Administration Card.

（3）Administration Card List
7.2Issue User Card
Issue User Card (method 1):
1）Choose “Card Issuing”in “Door Card”.
2）Press “Apply”to submit new User Card.
3) Put IC card on the Reader Sensing Area, and make sure the reader responded.
4）Choose “Normal”in the Card Reader Setting.