Fanvil i30 User manual

SIP Video Door Phone
Quick Installation Guide
i30 WWW.FANVIL.COM

Table of Contents
1. Package Contents ............................................................................... 4
2. Physical Specifications ....................................................................... 4
3. Installation ......................................................................................... 8
4. Searching Door Phone ..................................................................... 11
5. SIP Door Phone Setting .................................................................... 12
6. Door Unlocking Setting .................................................................... 14

1. Package Contents
2. Physical Specifications
Device size 160 x 93 x 35 mm
Weight 330g
1) Front Panel
Door Phone
Connectors
Quick Installation
Guide
CD
RFID Cards
Screw and
Wrench
MIC
RFID Reader
Numeric Keyboard
DSS Key
Lock
Call & Ring
Network/SIP Registration
Speaker
Camera

Interface Description
Speaker
The door phone has a built-in speaker for convenient communication
and alert use.
MIC
The door phone has a built-in microphone hidden in the pinhole
located on the front panel.
RFID Reader Use RFID cards to unlock the door by touching RFID reader of device.
Button Definition
Button Description
DSS Key Press the button, to make a call or request to open the door.
Numeric Keyboard Input password to open the door or make a call.
LED Definition
LED Status Description
Lock
Steady blue Door unlocking
off Door locking
Call & Ring
Blinks per second Call holding or ringing
off On hook
Blinks every 3 seconds Device in the issuing state
Steady blue Online talking
Network & SIP
Registration
Blinks per second Network error
off Network is normal, SIP is not registered
Blinks every 3 seconds SIP Registration failed
Steady blue SIP Registration succeeded
2) Port Definition
After removing the Back Panel of i30, there are one terminal block connectors for power and lock control connection
as shown in the picture below.
JP1 Jumper
Power and lock
connector
Network port

Network Connector
Power and Electric-lock Connectors
1 2 3 4 5 6 7
+DC12V VSS NC COM NO S-IN S-OUT
12V DC Input Electric-lock switch Indoor switch
JP1 Jumper
There are two modes for power supply of electric-lock as shown in the picture below.
(The default is “Active Mode”).
Passive Mode: When the electric-lock starting current is more than 12V/700mA, i30 needs to use the external
drive mode, the electric lock interface with short circuit output control.
Active Mode : When the electric-lock starting current is less than 12V/700mA, i30 can use the internal drive
mode, the electric lock interface with 12V DC output.

Wiring instructions
NO: Normally open contact
COM: Relay contact
NC: Normally closed contact
Driving Mode Electric-lock Mode
JP1
Jumper
Connections
Active Passive
No electricity
when open
Electrify
when open
√ √
√ √
√ √
√ √
√ √

3. Installation
Main Part of Intercom Back Panel Wall-mounted Shell
Figure 1 Three Major Parts of i30
Step 1: Installation preparation
A. Check the following contents:
 Hex wrench x 1
 RJ45 plugs x 2 (1 spare)
 KA4 x 25mm screws x 4
 25mm screw anchors x4
B. Tools that may be required:
 Hex wrench
 Phillips screwdriver (Ph2 or Ph3), hammer, RJ45 crimper
 Electric impact drill with an 6mm drill bit
Step 2: Drilling
Figure 2 Wall Mounting
A. Place the mounting template with dimensions on the surface of a wall in a desired flat position.
B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about
30mm deep. Remove the template when you finished drilling.
C. Push or hammer screw anchors into the drilled holes.
Step 3: Removing hanging shell
A. Remove the hanging shell as shown in Figure 3 and Figure 4.

Figure 3 Figure 4
B. With Phillips screwdriver, unpack the back panel and the main part of intercom as shown in Figure 5.
Figure 5
Step 4: Hanging shell fixing and cabling
Figure 6
A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended.
B. With 4 KA4 x 25mm screws, tighten the wall-mounted shell as shown in Figure 6.
Step 5: Connection line

Figure 7 Figure 8
A. Select the hole for cable supply.
B. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors
description (refer to Section 2).
C. Test whether there is electricity by doing the following:
Press the # button for 3 seconds to get the IP address of intercom by voice.
Input access password or press the indoor switch to check electric-lock installation.
Note: Do not proceed mounting until you have finished the electric checking.
Step 6: Mounting
Figure 9 Figure 10
A. Use the 4 screws to tighten the main part of intercom on the back panel as shown in Figure 9.
B. Push the device into the wall-mounted shell and tighten it with 1 screw as shown in Figure 10.
C. Make sure the screws have been tightened properly for better waterproof effect.

4. Searching Door Phone
There are two methods as shown below to search the i30.
Method 1:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the i30 and find the IP address.
Method 2:
Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice.
Default Setting
Default DHCP Client On
Static IP Address 192.168.1.179
Default Web Port 80
Default Login User Name admin
Default Login Password admin
Display IP Address Hold # for 3 seconds to display by voice
Search Tools iDoorPhone Network Scanner