Fibocom L860-GL User manual

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
L8-Family AT Commands User Manual Page 1 of 254
FIBOCOM L860 AT Commands
User Manual
Version: V3.2.3
Date: 2019.05.08

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 2 of 254
Applicability Type
No. Type Note
1 L860-GL NA

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 3 of 254
Copyright
Copyright ©2019 Fibocom Wireless Inc . All rights reserved.
Without the prior written permission of the copyright holder, any company or individual is prohibited to
excerpt, copy any part of or the entire document, or transmit the document in any form.
Attention
The document is subject to update from time to time owing to the product version upgrade or other
reasons. Unless otherwise specified, the document only serves as the user guide. All the statements,
information and suggestions contained in the document do not constitute any explicit or implicit
guarantee.
Trademark
The trademark is registered and owned by Fibocom Wireless Inc.
Versions
Version Author Date Remarks
V3.2.1 2018-05-04 Initial version
V3.2.2 2019-3-5
1. Delete commands not supported by L860：+TPIN、
+MSMPD、+MGAUTH、+SMMFULL、+GPIO
2. Add commands to customers：+XMCI、+XCCINFO、
+XGAUTH、+XLEC、+XAUTH、+XCESQ、+XCESQRC、
+XDATACHANNEL、+XDNS、+XSYSTRACE、
+XADPCLKFREQINFO
3. Delete unsupported functions：AT+CIMI? AT+CNUM?
4. Modify the description of the cid scope：according to 3GPP
protocol 27007 and L860 code，pdp context cid scope is:
[0~29]，not [1~20]
5. Modify the description of the +CSCON command
Parameters
6. Modify the description of the +CGTFT command
Parameters,AT+CGTFT=? It actually returns 12

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 4 of 254
Version Author Date Remarks
parameters, but the previous documentation only had
instructions for 11 parameters
7. Modify the description of the + CTZR
V3.2.3 2019-5-8
1. Delete the unsupportedAT command: +GTUSBMODE
2. Normalization processing these test AT commands:
+CFUN、+GTWAKE、+CTZU、+CNMI、+CSCB、+CGEQMIN
、
+CGEQREQ、+CGEREP, change (0-1) to (0,1)
3. Delete the unsupportedAT command: +CBC
4. Modify the description of the command +CPINR, wildchar
patterns are changed.
5. Add the AT command: +MSMPD
6. Normalization processing theseAT commands:+ CGMM、
+CGMI、+CGMR、+CFSN、+CGSN, add double quotes

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 5 of 254
Contents
1Preface .........................................................................................................................10
1.1 Target Audience..........................................................................................................10
2Introduction to AT Commands ...................................................................................10
2.1 AT Commands Overview............................................................................................10
2.2 General System Abbreviations....................................................................................10
2.3 AT Commands Protocol..............................................................................................10
2.4 Manual Scope ............................................................................................................11
2.5 AT Commands Structure.............................................................................................12
2.4.1 General Symbols Used in AT Commands Description.......................................................12
2.4.2 Command Structure............................................................................................................12
2.4.3 Results Code Structure.......................................................................................................12
2.6 Command Syntax.......................................................................................................13
3Modem Information.....................................................................................................13
3.1 Modem ID...................................................................................................................14
3.1.1 +CGMI, Request Manufacturer ID......................................................................................14
3.1.2 +GMI, Request Manufacturer ID........................................................................................15
3.1.4 +CGMM, Request Model ID...............................................................................................16
3.1.5 +GMM, Request Model ID..................................................................................................17
3.1.6 +FMM, Request Model ID ..................................................................................................18
3.1.7 +CGMR, Request Revision................................................................................................19
3.1.8 +GMR, Request Revision...................................................................................................20
3.1.9 +FMR, Request Revision ...................................................................................................21
3.1.10 +CGSN, Request Product Serial Number Identification ..................................................22
3.1.11 +GSN, Request Product Serial Number Identification.....................................................24
3.1.12 +CSCS, Select Terminal Character Set...........................................................................25
3.1.13 +CIMI, Request IMSI........................................................................................................26
3.1.14 +CFSN, Read Factory Serial Number..............................................................................27
3.1.15 I, Request Identification Information.................................................................................28
3.1.16 +CNUM, Request MSISDN(s)..........................................................................................29
3.1.17 +CLAC, List of All Available AT Commands.....................................................................31
4Modem Control and Status.........................................................................................31
4.1 Modem Register Commands......................................................................................31
4.1.1 V, Modem Response Format..............................................................................................32

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 6 of 254
4.1.2 Q, Result Code Suppression..............................................................................................33
4.1.3 E, Command Echo .............................................................................................................34
4.1.4 X, Result Code Selection and Call Progress Monitoring Control.......................................34
4.1.5 S, Bit Map Registers...........................................................................................................35
4.1.6 &F, Set to Factory Defined Configuration...........................................................................37
4.1.7 Z, Reset to Default Configuration.......................................................................................37
4.1.8 +CRSM, Restricted SIM Access.........................................................................................38
4.1.9 +CCID.................................................................................................................................43
4.1.10 +CSIM, Generic SIM Access............................................................................................44
4.2 Other Parameter Commands......................................................................................45
4.2.1 +CFUN, Set Phone Functionality.......................................................................................45
4.2.2 +MSMPD, Enable/Disable SIM card hot plug....................................................................48
4.2.3 +CPWROFF Switch off MS ................................................................................................50
4.2.4 +MTSM, Temperature Sensor Measurement.....................................................................51
4.2.5 +GTWAKE,Open or close wake host.................................................................................54
4.2.6 +MSTART, Start message notification................................................................................55
4.2.7 +GFSN, Set SN Number....................................................................................................57
4.3 Multiplexer Feature.....................................................................................................57
4.3.1 +CMUX, MUX Start up Command......................................................................................57
4.4 Error Handling Commands .........................................................................................60
4.4.1 +CMEE, Report Mobile Equipment Error...........................................................................60
4.4.2 +CEER, Extended Error Report.........................................................................................62
5Clock ............................................................................................................................63
5.1 System Date and Time Access Commands................................................................63
5.1.1 +CCLK, Read/Set System Date and Time.........................................................................63
5.1.2 +CTZU, Automatic Time Zone Update...............................................................................65
5.1.3 +CTZR, Time Zone Reporting............................................................................................67
6SMS ..............................................................................................................................69
6.1 SMS Commands ........................................................................................................69
6.1.1 +CSMS, Select Message Service......................................................................................69
6.1.2 +CPMS, Preferred Message Storage.................................................................................71
6.1.3 +CMGF, Message Format..................................................................................................73
6.1.4 +CSCA, Service Center Address .......................................................................................75
6.1.5 +CSMP, Set Text Mode Parameters...................................................................................78

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 7 of 254
6.1.6 +CSDH, Show Text Mode Parameters...............................................................................80
6.1.7 +CNMI, New Message Indications to Terminal..................................................................82
6.1.8 +CNMA, New Message Acknowledgment .........................................................................86
6.1.9 +CMTI, Unsolicited Response (New SMS-DELIVER Receipt Indication).........................89
6.1.10 +CMT, Unsolicited Response (New SMS-DELIVER Receipt).........................................89
6.1.11 +CBM, Unsolicited Response (New CB Message Receipt)............................................. 91
6.1.12 +CDSI, Unsolicited Response (New SMS-STATUS-REPORT Indication) ......................92
6.1.13 +CDS, Unsolicited Response (New SMS-STATUS-REPORT Receipt)...........................92
6.1.14 +CMGL, List Messages....................................................................................................94
6.1.15 +CMGR, Read Message..................................................................................................97
6.1.16 +CMSS, Send Message from Storage...........................................................................101
6.1.17 +CMGW, Write Message to Memory..............................................................................103
6.1.18 +CMGD, Delete Message..............................................................................................106
6.1.19 +CGSMS, Select Service for MO SMS Messages.........................................................107
6.1.20 +CMGS, Send SMS to Network.....................................................................................109
6.1.21+CSCB, Cell Broadcast Messages ..................................................................................111
7SIM TOOL KIT Raw Mode Commands .....................................................................113
7.1 Raw Mode Commands Lists.....................................................................................113
7.1.1 +CUSATR, Read USAT Profile......................................................................................... 113
7.1.2 +CUSATW, Write USAT Profile................................................................................... 114
7.1.3 +CUSATD, Profile download upon start-up................................................................ 116
7.1.4 +CUSATA, Activate USAT profile................................................................................ 119
7.1.5 +CUSATT, Send USAT terminal response..................................................................121
7.1.6 +CUSATE, Send USAT envelope command..............................................................122
7.1.7 +STKPROF, Reading and changing the terminal profile............................................123
8. Access and security..................................................................................................125
8.1 Commands...............................................................................................................125
8.1.1 A/, Repeat Last Command..........................................................................................125
8.1.2 AT, Check AT Communication.....................................................................................125
8.1.3 +CPIN, Enter PIN for Unlocking SIM or Enter PUK for Unblocking SIM....................126
8.1.4 +CPWD, Change Password........................................................................................130
8.1.5 +CLCK, Facility Lock...................................................................................................133
8.1.6 +CPINR, Remaining PIN Retries................................................................................136
9Network......................................................................................................................138

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 8 of 254
9.1 Network Commands.................................................................................................138
9.1.1 +CSQ, Signal Strength................................................................................................138
9.1.2 +CESQ, Extended Signal Quality...............................................................................140
9.1.3 +CRLP, Radio Link Protocol........................................................................................143
9.1.4 +CREG, Network Registration Status .........................................................................144
9.1.5 WS46, Select Wireless Network.................................................................................147
9.1.6 +CGREG, GPRS Network Registration ......................................................................149
9.1.7 +CEREG, EPS Network Registration status...............................................................153
9.1.8 +COPS, Operator Selection........................................................................................156
9.1.9 +CPLS, Selection of Preferred PLMN List..................................................................159
9.1.10 +CPOL, Preferred Operators......................................................................................161
9.1.11 +COPN, Read Operator Names .................................................................................164
9.1.12 +CEMODE, UE modes of operation for EPS..............................................................165
9.1.13 +XMCI, Measured Cell Information.............................................................................167
9.1.14 +XCCINFO, Camped Cell Information........................................................................169
9.1.15 +XGAUTH, Set Type of Authentication.......................................................................170
9.1.16 +XLEC, LTE Extended Cell info..................................................................................172
9.1.17 +XAUTH, UICC AUTHENTICATE command..............................................................173
9.1.18 +XCESQRC, Extended Signal Quality Reporting Configuration................................175
9.1.19 +XCESQ, Extended signal quality with URC support.................................................177
9.1.20 + XDATACHANNEL, Configure the Data Channel.....................................................179
9.1.21 +XDNS, Dynamic DNS Request.................................................................................181
9.1.22 +XSYSTRACE, Configure System Trace ...................................................................183
9.1.23 +XADPCLKFREQINFO,Adaptive Clock Frequency Info...........................................184
10 Hardware Information.........................................................................................186
10.1 Clock Configuration..................................................................................................186
10.1.1 +CLK26M, 26MHz Clock Output From CLK26M........................................................186
11 GPRS....................................................................................................................187
11.1 GPRS Functionality..................................................................................................187
11.2 GPRS Commands....................................................................................................187
11.2.1 +CGCLASS, GPRS Mobile Station Class...................................................................188
11.2.2 +CGDCONT, Define PDP Context..............................................................................189
11.2.3 +CGQMIN, Quality of Service Profile (Min Acceptable) .............................................193
11.2.4 +CGQREQ, Quality of Service Profile (Requested)...................................................195

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 9 of 254
11.2.5 +CGATT, GPRS Attach or Detach ..............................................................................197
11.2.6 D*99, Request GPRS Service "D"..............................................................................198
11.2.7 +CGACT, PDP Context Activate or Deactivate...........................................................201
11.2.8 +CGPADDR, GPRS Addresses..................................................................................202
11.2.9 +CGANS, Manual response to a network request for PDP context activation...........204
11.2.10 +CGAUTO, Automatic Response to a Network Request for PDP Context Activation
206
11.2.11 +CGEQMIN
， 3G Quality of Service Profile (Minimum acceptable)....................208
11.2.12 +CGEQREQ
， 3G Quality of Service Profile (Requested)..................................213
11.2.13 +CGEQNEG
， G Quality of Service Profile (Negotiated)....................................217
11.2.14 +CGCMOD
， PDP Context Modify......................................................................220
11.2.15 +CGDATA
， Enter Data State..............................................................................221
11.2.16 +CGDSCONT
， Define Secondary PDP Context................................................223
11.2.17 +CGEREP
， Packet Domain Event Reporting....................................................225
11.2.18 +CGTFT Traffic Flow Template............................................................................227
11.2.19 +CGEV, Unsolicited Packet Domain Event Reporting ........................................230
11.2.20 +CGPIAF , Printing IPAddress Format...............................................................232
11.2.21 +CGCONTRDP, PDP Context Read Dynamic Parameters ................................235
11.2.22 +CGSCONTRDP, PDP Context Read Dynamic Parameters..............................237
11.2.23 +CGTFTRDP, Traffic Flow Template Read Dynamic Parameters.......................239
11.2.24 +CSCON, Signalling Connection Status..............................................................242
11.2.25 +CGEQOS, Define EPS Quality Of Service........................................................244
12 Fibocom Proprietary Commands.......................................................................246
12.1 Set Profile Commands..............................................................................................246
12.1.1 +GTMCFWVER, Get Original FW Version.................................................................246
13 Multi-Config Commands.....................................................................................247
14 GNSS Commands ...............................................................................................247
15 SAR Commands..................................................................................................248
16 RF Commands.....................................................................................................248
17 Error Code ...........................................................................................................248
17.1 CME Error ................................................................................................................248
17.2 CMS Error ................................................................................................................251

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 10 of 254
1 Preface
1.1 Target Audience
This manual is intended for the developers who need to communicate with the L8 family devices using the
AT commands.
2 Introduction to AT Commands
2.1 AT Commands Overview
AT commands are sets of commands used for communication with the cellular modem. AT commands are
comprised of assemblies of ASCII characters which start with the "AT" prefix (except the commands A/
and +++). The AT prefix is derived from the wordAttention, which asks The modem to pay attention to the
current request (command).
AT commands are used to request services from the cellular modem, such as:
Call services: dial, answer and hang up
Cellular utilities: send/receive SMS
Modem profiles: Auto Answer
Cellular Network queries: GSM signal quality
2.2 General System Abbreviations
The basic system configuration contains a modem and a terminal.
The L8 family is the modem unit and may be referred to as the DCE or TA, such as the phone, the mobile
or the radio.
The terminal (PC or MCU) may be referred to as the DTE or the TE.
2.3 AT Commands Protocol
TheAT commands interface is basically a Modem Services upon Request.
Communication (almost) always begins from the TE side. This means that any service should be
requested from the TE. Thus a request is called a "Command".

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 11 of 254
Each command must be answered by a "Results code" from the TA. The results code reports the
command status to the TE. Some commands may include several "Results code" to send data back to the
TE. Some commands may initiate a mode in which, when specified events are generated in the modem,
"Indicator" messages are sent data asynchronously. The “indicators” can be called “Unsolicited results
code”.
The Modem can echo characters received from the TE (commands) back to the TE.
2.4 Manual Scope
This manual introduces the AT commands set of L8 family products, and describes how the users can
communicate with the devices using these commands. It describes the specification of syntax and
parameters of the listed AT commands.
TE TA
Command
Results code
TE TA
Command
Results code
TE TA
Unsolicited results code

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 12 of 254
2.5 AT Commands Structure
2.4.1 General Symbols Used in AT Commands Description
The following syntax definitions apply in this chapter:
Syntax
Definition
<CR> Carriage returns character, specified by the value of the S3-register.
<LF>
Line-feed character, specified by the value of the S4-register.
<…>
Name enclosed in angle brackets is a syntax element. The brackets themselves
do not appear in the command line.
[...] Optional sub-
parameter of a command or an optional part of terminal information
response, enclosed in square brackets. The brackets themselves do not appear
in the command line. When the sub-parameter is not provided in the parameter
type commands, the new value equals its previous value. In action type
commands, the action should be performed on the basis of the recommended
default setting of the sub-parameter.
// Denotes a comment, and should not be included in the command.
2.4.2 Command Structure
EachAT command has the "AT" or “at” prefix string (except the commandsA/ and +++).
EachAT command has the suffix <CR> (except the commandsA/ and +++).
Example:
AT+CSQ<CR>
An AT command line may contain one or more commands. Delimiters are used to separate the
commands from each other. The delimiter is either a semicolon ";" or none, meaning space (basic
commands).
Example:
ATS0=1V1Q0E0<CR>
AT+IFC=0,0;+ICF=3,4;+CNMI=2,1,0,0,0<CR>
2.4.3 Results Code Structure
By default, the Modem responds with verbose response codes. The results code prefix is <CR><LF>. The
results code suffix is <CR><LF>.

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 13 of 254
Example:
<CR><LF>+CSQ: 99,99<CR><LF>
<CR><LF>OK<CR><LF>
The unsolicited results code is same as the Results code.
Note:
The <CR> and <LF> characters are not explicitly presented in the response format in this
document.
To reduce the print length the empty line in actual response may be removed in the
examples.
2.6 Command Syntax
Execute command syntax AT+xxx
ATxxx
ATxxx;
Parameter set command syntax AT+xxx=<Value>
ATxxx=<Value>
Parameter read Command syntax AT+xxx?
ATxxx?
Parameter test Command syntax AT+xxx=?
ATxxx=?
<Value> consists of either a numeric constant or a string constant. <compound_value> consist of several
<value> parameters separated by commas.
Example of compound_value: <value1>, <value2>,…,<valueN>
Numeric Constants
Numeric constants are expressed in decimal, hexadecimal, or binary form. In the Modem, the definition
of each command specifies which form is used for values associated with that command.
String Constants
String constants consist of a sequence of characters, bounded at the beginning and end by the
double-quote character (").
3 Modem Information
These commands allow the user to query the type of device that is attached, the technology used in the
device, as well as basic operating information about the modem unit.

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 14 of 254
3.1 Modem ID
3.1.1 +CGMI, Request Manufacturer ID
This command displays the manufacturer identification. The modem unit outputs a string containing
manufacturer identification information.
Command Description
Execution [Function]
The Execution command displays manufacture identification. The modem unit outputs
a string containing manufacture identification information.
[Syntax]
AT+CGMI
[Response/Action]
+CGMI: "<manufacture ID>"
OK
Read [Function]
The Read command displays manufacture identification. The modem unit outputs a
string containing manufacture identification information.
[Syntax]
AT+CGMI?
[Response/Action]
+CGMI: "<manufacture ID>"
OK
Test N/A
Parameters N/A
Example AT+CGMI
+CGMI: "Fibocom"

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 15 of 254
Command Description
OK
Reference 3GPP TS 27.007
3.1.2 +GMI, Request Manufacturer ID
This command displays manufacturer identification. The modem unit outputs a string containing
manufacturer identification information.
Command
Description
Execution [Function]
The Execution command displays manufacture identification. The modem unit outputs
a string containing manufacture identification information.
[Syntax]
AT+GMI
[Response/Action]
+GMI: "<manufacture ID>"
OK
Read [Function]
The Read command displays manufacture identification. The modem unit outputs a
string containing manufacture identification information.
[Syntax]
AT+GMI?
[Response/Action]
+GMI: "<manufacture ID>"
OK
Test N/A

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 16 of 254
Command
Description
Parameters
N/A
Example AT+GMI
+GMI: "Fibocom"
OK
3.1.4 +CGMM, Request Model ID
This command requests the model identification. The modem outputs a string containing information
about the specific model, including a list of the supported technology used, and the particular model
number.
Command Description
Execution [Function]
The Execution command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+CGMM
[Response/Action]
+CGMM: "<list of supported technologies>","<model>"
OK
Read [Function]
The Read command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+CGMM?

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 17 of 254
Command Description
[Response/Action]
+CGMM: "<list of supported technologies>", "<model>"
OK
Test N/A
Parameters N/A
Example AT+CGMM
+CGMM: "L860 LTE Module","L860"
OK
Reference 3GPP TS 27.007
3.1.5 +GMM, Request Model ID
This command requests the model identification. The modem outputs a string containing information
about the specific model, including a list of the supported technology used, and the particular model
number.
Command Description
Execution [Function]
The Executions command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+GMM
[Response/Action]
+GMM: "<list of supported technologies>","<model>"
OK
Read [Function]

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 18 of 254
Command Description
The Read command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+GMM?
[Response/Action]
+GMM: "<list of supported technologies>","<model>"
OK
Test N/A
Parameters N/A
Example AT+GMM
+GMM: "L860 LTE Module","L860"
OK
3.1.6 +FMM, Request Model ID
This command requests the model identification. The modem outputs a string containing information
about the specific model, including a list of the supported technology used, and the particular model
number.
Command Description
Execution [Function]
The Execution command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+FMM
[Response/Action]

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 19 of 254
Command Description
+FMM: "<list of supported technologies>","<model>"
OK
Read [Function]
The Read command displays model identification. The modem outputs a string
containing information about the specific model, including a list of the supported
technology used, and the particular model number.
[Syntax]
AT+FMM?
[Response/Action]
+FMM: "<list of supported technologies>","<model>"
OK
Test N/A
Parameters N/A
Example AT+FMM
+FMM: "L860 LTE Module","L860"
OK
3.1.7 +CGMR, Request Revision
This command requests the revision identification. The modem outputs a string containing the revision
identification information of the software running in the device.
Command Description
Execution [Function]
The Execution command requests the revision identification. The modem outputs a
string containing the revision identification information of the software running in the
device.
[Syntax]
AT+CGMR

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved.
FIBOCOM L860 AT Commands User Manual Page 20 of 254
Command Description
[Response/Action]
+CGMR: "<revision>"
OK
Read [Function]
The Read command requests the revision identification. The modem outputs a string
containing the revision identification information of the software version contained within
the device.
[Syntax]
AT+CGMR?
[Response/Action]
+CGMR: "<revision>"
OK
Test N/A
Parameters N/A
Example AT+CGMR
+CGMR: “18600.5001.00.35.00.13”
OK
Reference 3GPP TS 27.007
3.1.8 +GMR, Request Revision
These commands request the revision identification. The modem outputs a string containing the revision
identification information of the software version contained within the device.
Command Description
Execution [Function]
The Execution command requests the revision identification. The modem outputs a
string containing the revision identification information of the software version contained
within the device.
[Syntax]
AT+GMR