Fibocom H330S Instructions for use

第1页 共 44 页
H330S Hardware User Manual
Version：V1.1.7
Date：2016.06.17

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
2
of
44
Applicability Type
No.
Type
Note
1
H330S-Q50-00
2
H330S-Q30-00
NA
3
H330S-A30-00
NA
4
H330S-A50-00
NA
5
H330S-A30-20
NA
6
H330S-A50-20
仅有 MiniPCIe 型号
7
H330S-Q50-20
仅有 MiniPCIe 型号
8
H330S-Q30-20
NA
The difference of H330S series wireless module as listed below:
Model No.
GSM/GPRS/EDGE
Band(MHz)
WCDMA Band(MHz)
Voice
HSDPA
(Mbps)
HSUPA
(Mbps)
H330S-Q50-00
850/900/1800/1900
850/900/1900/2100
Y
21
5.76
H330S-Q30-00
850/900/1800/1900
850/900/1900/2100
Y
7.2
5.76
H330S-A30-00
900/1800
900/2100
Y
7.2
5.76
H330S-A50-00
900/1800
900/2100
Y
21
5.76
H330S-A30-20
900/1800
900/2100
N
7.2
5.76
H330S-A50-20
900/1800
900/2100
N
21
5.76
H330S-Q50-20
850/900/1800/1900
850/900/1900/2100
N
21
5.76
H330S-Q30-20
850/900/1800/1900
850/900/1900/2100
7.2
5.76

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
3
of
44
Copyright
Copyright ©2015 Fibocom Wireless Inc . All rights reserved.
Without the prior written permission of the copyright holder, any company or individual is prohibited to
excerpt, copy any part of or the entire document, or transmit the document in any form.
Attention
The document is subject to update from time to time owing to the product version upgrade or other
reasons. Unless otherwise specified, the document only serves as the user guide. All the statements,
information and suggestions contained in the document do not constitute any explicit or implicit
guarantee.
Trademark
The trademark is registered and owned by Fibocom Wireless Inc.
Versions
Version
Date
Remarks
V1.0.0
2012-05-30
Initial Version
V1.0.1
2012-07-06
Update product model No.
V1.0.2
2012-08-08
Update Mechanical, PCB Design, Pin Out
V1.0.3
2012-11-20
Modify Pin description and incorrect specifications
V1.0.4
2013-01-09
Update the name of the document; add reliability features
V1.0.5
2013-01-24
Update the document name
V1.0.6
2013-05-02
Update the name of the manual
Add UART_R1
Add model comparisons
Update the current specification
V1.0.7
2013-07-01
Add two models
Add comparison on voice
V1.0.8
2013-09-13
SMI is updated to a output pin; update section 5.4.1;
Update Figure5-2, Figure5-4;

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
4
of
44
Update description of RTC
Add section 5.8.3
Update section 5.3.2.3 WAKE_UP
V1.0.9
2013-10-12
Update description for ADC, POWER OFF and RESET.
V1.1.0
2013-12-18
Modify I2S signal Pin # in section 5.8.
Add default status and idle status of GPIO
Update downstream rate and upstream rate of GPRS
Update the maximum operating voltage to 4.2V
V1.1.1
2015-01-30
Update the range of operating temperature.
V1.1.2
2015-04-21
Add the description of “Top View” in PCB Layout
V1.1.3
2015-05-10
Update the description of copyright and attention.
Update the translation of the whole document.
V1.1.4
2015-07-27
Update the info of H330S and the logo.
V1.1.5
2015-09-22
Update the 12C and 12S description of H330S-XXX-20
V1.1.6
2015-11-17
Update the maximum operating voltage to 4.2V
V1.1.7
2016-06-17
Add the H330S-Q30-20

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
5
of
44
Contents
1 Foreword.............................................................................................................................................. 8
1.1 Introduction................................................................................................................................................... 8
1.2 Reference Standards................................................................................................................................. 8
2 Product Overview..............................................................................................................................9
2.1 Description.................................................................................................................................................... 9
2.2 Specifications............................................................................................................................................... 9
2.3 Appearance................................................................................................................................................ 12
3 Structure.............................................................................................................................................13
3.1 Dimension Diagram of Structure...........................................................................................................13
3.2 PCB Layout Design.................................................................................................................................. 13
4 Hardware Introduction.................................................................................................................. 14
4.1 Hardware Block Diagram........................................................................................................................ 14
4.2 Pin Definition.............................................................................................................................................. 15
4.2.1 Pin Map............................................................................................................................................. 15
4.2.2 Description of Pins...........................................................................................................................16
5 Hardware Interface......................................................................................................................... 22
5.1 Power Interface......................................................................................................................................... 22
5.1.1 Power Supply................................................................................................................................... 22
5.1.2 Power Consumption........................................................................................................................22
5.1.3 VIO..................................................................................................................................................... 25
5.1.4 VRTC................................................................................................................................................. 26
5.2 Power on/off and Reset Signal..............................................................................................................27
5.2.1 Pin Definition of Power on/off Control Signal..............................................................................27
5.2.2 Power on Signal...............................................................................................................................27
5.2.3 Power off Signal...............................................................................................................................28
5.2.4 Reset Signal..................................................................................................................................... 29
5.3 Status Indicating Signal...........................................................................................................................30
5.3.1 LPG Signal........................................................................................................................................30
5.3.2 SMI Signal.........................................................................................................................................30

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
6
of
44
5.3.3 WAKE_UP Signal............................................................................................................................ 31
5.3.4 Other Work Indications................................................................................................................... 31
5.4 USB Interface.............................................................................................................................................32
5.4.1 USB Interface Definition................................................................................................................. 32
5.4.2 USB Interface Application.............................................................................................................. 32
5.5 UART Interface..........................................................................................................................................33
5.5.1 UART Interface Description........................................................................................................... 33
5.5.2 UART Interface Application............................................................................................................34
5.5.3 Ring Indication................................................................................................................................. 35
5.6 USIM Interface...........................................................................................................................................35
5.6.1 USIM Pins......................................................................................................................................... 35
5.6.2 USIM Design.................................................................................................................................... 35
5.6.3 Points for Attention in USIM Design.............................................................................................36
5.6.4 USIM Hot-Plugging..........................................................................................................................36
5.6.4.1 Hardware Connection............................................................................................................ 37
5.6.4.2 Software Settings................................................................................................................... 37
5.7 Analog Audio Interface............................................................................................................................ 37
5.7.1 Definition of Audio Interface Signals............................................................................................ 37
5.7.2 Description of Audio Interface Application.................................................................................. 38
5.7.2.1 Audio Channel 1..................................................................................................................... 38
5.7.2.2 Audio Channel 2..................................................................................................................... 38
5.8 Digital Audio............................................................................................................................................... 39
5.8.1 I2S...................................................................................................................................................... 39
5.8.2 I2C......................................................................................................................................................40
5.8.3 PCM Port Description..................................................................................................................... 40
5.9 ADC Interface.............................................................................................................................................40
5.10 Other Interfaces...................................................................................................................................... 41
6 Electrical and Environmental Features...................................................................................41
6.1 Electrical Features.................................................................................................................................... 41
6.2 Environmental Features.......................................................................................................................... 41
7 RF Interface.......................................................................................................................................42
7.1 Operating Frequency Band.................................................................................................................... 42
7.1.1 Frequency Range of Main Antenna..............................................................................................42

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
7
of
44
7.2 RF PCB Design......................................................................................................................................... 42
7.2.1 Wiring Principle................................................................................................................................ 42
7.2.2 Impedance Design...........................................................................................................................43
7.3 Antenna Design.........................................................................................................................................43
7.3.1 Main Antenna Design Requirements........................................................................................... 43
7.3.1.1 Antenna efficiency.................................................................................................................. 43
7.3.1.2 S11 or VSWR..........................................................................................................................43
7.3.1.3 Polarization..............................................................................................................................43
7.3.1.4 Radiation pattern.................................................................................................................... 43
7.3.1.5 Gain and directivity.................................................................................................................43
7.3.1.6 Interference............................................................................................................................. 44
7.3.1.7 TRP/TIS...................................................................................................................................44

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
8
of
44
1 Foreword
1.1 Introduction
The document describes the electrical characteristics, RF performance, dimensions and application
environment, etc. of H330S series wireless modules. With the assistance of the document and other
instructions, developers can quickly understand the performance of H330S series wireless modules and
develop products.
1.2 Reference Standards
The design of the product complies with the following standards:
3GPP TS 27.007 -v6.9.0: AT command set for User Equipment (UE)
3GPP TS 27.005 -v6.0.1: Use of Data Terminal Equipment -Data Circuit terminating Equipment
(DTE-DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)
3GPP TS 23.040 -v6.9.0: Technical realization of Short Message Service (SMS)
3GPP TS 24.011 -v6.1.0: Point- to - Point (PP) Short Message Service (SMS) support on mobile
radio interface
3GPP TS 27.010 -v6.0.0: Terminal Equipment to User Equipment (TE-UE) multiplexer protocol
3GPP TS 27.060 -v6.0.0: Packet domain; Mobile Station (MS) supporting Packet Switched services
3GPP TS 25.304-v6.10.0: User Equipment (UE) procedures in idle mode and procedures for cell
reselection in connected mode
3GPP TS 25.308 -v6.4.0: High Speed Downlink Packet Access (HSDPA); Overall description;
Stage 2
3GPP TS 25.309 -v6.6.0: FDD enhanced uplink; Overall description; Stage 2
3GPP TS 23.038 -v6.1.0: Alphabets and language - specific information
3GPP TS 21.111 -v6.3.0: USIM and IC card requirements
3GPP TS 31.111 -v6.11.0 "USIM Application Toolkit (USAT)"
3GPP TS 45.002 -v6.12.0: Multiplexing and multiple access on the radio path
3GPP TS 51.014 -v4.5.0: Specification of the SIM Application Toolkit for the Subscriber Identity
Module - Mobile Equipment (SIM-ME) interface
3GPP TS 51.010 -1 -v6.7.0: Mobile Station (MS) conformance specification; Part 1: Conformance
specification
3GPP TS 22.004 -v6.0.0: General on supplementary services
3GPP TS 23.090 -v6.1.0: Unstructured Supplementary Service Data (USSD); Stage 2
3GPP TS 24.008 v6.19, Mobile radio interface Layer 3 specification;

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
9
of
44
2 Product Overview
2.1 Description
H330S series modules are 3G wireless modules with high integration density, supporting GSM/GPRS/
EDGE and UMTS/HSDPA/HSUPA/HSPA+.
2.2 Specifications
Specifications
Operating
Frequency Range
UMTS (WCDMA/FDD): 850/900/1900/2100 MHz or 900/2100MHz
GSM/GPRS/EDGE: 850/900/1800/1900 MHz or 900/1800MHz
Data Rate
UMTS/HSDPA/HSUPA 3GPP release 7
HSUPA 5.76Mbps (Cat 6)
HSDPA 21Mbps (Cat 14) or 7.2Mbps (Cat 8)
GSM 3GPP release 7
EDGE (E-GPRS) multi-slot class 33 (296kbps DL, 236.8kbps UL)
GPRS multi-slot class 33 (107kbps DL, 85.6kbps UL)
Physical
Characteristics
Dimension: 33.8 x 27.8 x 2.45mm
Interface: LGA
Weight: <5.5 grams
Environment
Normal operating Temperature: -30℃~ +75℃
Restricted operating temperature①: -40℃~ +85℃
Storage Temperature: -40℃~ +85℃
Performance
Operating
Voltage
Voltage: 3.3V ~ 4.2V Normal: 3.8V
Current
Consumption
(Typical Value)
2mA (Sleep Mode)
3G Idle: 13mA
3G Talk: 500mA

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
10
of
44
2G Talk: 260mA (GSM PCL5)
Tx Power
(Typical Value)
Class 4 (2W) : 850/900 MHz, GSM
Class 1 (1W) : 1800/1900 MHz, GSM
Class E2 (0.5W) : 850/900 MHz, EDGE
Class E2 (0.4W) : 1800/1900 MHz, EDGE
Class 3 (0.25W) : 850/900/1900/2100 MHz, WCDMA
Rx Sensitivity
(Typical Value)
UMTS/HSPA: -109dBm
GSM: -108dBm
Interfaces
Rf Interface
Main Antenna
Function
Interface
1 x USB 2.0
2 x UART
MUX Over UART1
Multiple Profiles over USB
SPI Support (Not supported yet)
I2C Support②
I2S Support②
PCM, HSIC, GPIO, A/D, RTC
Data Features
Protocol Stack
Embedded TCP/IP and UDP/IP protocol stack
EDGE
Multi-slot class 33(5 Down; 4 Up; 6 Total)
Coding Scheme MCS1~9
GPRS
Multi-slot class 33(5 Down; 4 Up; 6 Total)
Coding Scheme CS1~4
CSD
UMTS(14.4kbps), GSM(9.6kbps)
USSD
Support
SMS
MO / MT Text and PDU modes

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
11
of
44
Cell broadcast
Audio
Analog Audio and Digital Audio②
Voice coders: EFR/HR/FR/AMR
Audio Frequency
Control
Gain Control, Echo Cancellation, Noise Suppression, Sidetone
Character Set
IRA
GSM
UCS2
HEX
AT Commands
FIBOCOM proprietary AT commands
GSM 07.05
GSM 07.07
Accessories
Firmware Loader Tool over USB/UART
User Manual
Developer Kit
Note：
①:For the temperature is out of the normal temperature range: -30℃~ +75, some indexes may
slightly deviate from the related 3GPP codes.
②：H330S-XXX-20 serials module dose not support I2C/I2S/Analog Audio and Digital Audio.

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
12
of
44
2.3 Appearance
The product appearance of H330S series wireless module is shown as below:
Top view:
Figure 2- 1 Top View
Bottom view:
Figure 2- 2 Bottom View

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
13
of
44
3 Structure
3.1 Dimension Diagram of Structure
Figure 3- 1 Dimension Diagram of Structure
3.2 PCB Layout Design
Figure 3- 2 Recommended PCB Layout
(Top View)

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
14
of
44
4 Hardware Introduction
4.1 Hardware Block Diagram
Figure 4- 1 Block Diagram

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
15
of
44
4.2 Pin Definition
4.2.1 Pin Map
TOP (View)
Figure 4-2 Pin Diagram

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
16
of
44
4.2.2 Description of Pins
The logic signal lever of H330S series is 1.8V. Pins of H330S series are described in the table below:
Pin #
Pin Name
I/O
Reset
Value
Idle
Value
Description
Power Supply
59
VBAT
I
Main power supply, voltage range: 3.3V ~
4.2V.
60
VBAT
I
61
VBAT
I
62
VBAT
I
64
VPA
O
Test pin for power supply of RF power
amplifier .Idle state in actual use.
1
VTRX
O
Test pin for transceiver power supply .
Idle state in actual use
46
VIO
O
1.8V voltage output inside the modules.
47
VRTC
I/O
Backup battery input/output.
Power ON/OFF Signal
48
POWER_OFF
I
PU
PU
Power off control signal, internal 4.7K
pull-up resistor
49
POWER_ON
I
PU
PU
Power on control signal, internal 200K
pull-up resistor
Reset Signal
77
RESET_ALL_N
I
PU
PU
External reset signal input, internal 200K
pull-up resistor
USIM Interface
4
USIM_CD
I
PU
PU
Insert USIM card to test; active low;
Internal 390K pull-up resistor.
5
USIM_VCC
O
USIM card power supply: 1.8V or 3.0V
6
USIM_RST
O
PP
PP
USIM card reset signal.
7
USIM_CLK
O
PP
PP
USIM card clock signal.
8
USIM_DATA
I/O
PU
PU
USIM card data signal, internal 4.7K
pull-up resistor.

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
17
of
44
Pin #
Pin Name
I/O
Reset
Value
Idle
Value
Description
High Speed SIM Interface
9
USIM_D+
High speed SIM card USB signal +
(Temporarily not supported)
10
USIM_D-
High speed SIM card USB signal -
(Temporarily not supported)
Audio Interface
13
AUXO+
O
Speaker output signal +
14
AUXO-
O
Speaker output signal -
15
EAR-
O
Earphone signal output -
16
EAR+
O
Earphone signal output +
17
MIC+
I
Main MIC input signal +
18
MIC-
I
Main MIC input signal -
19
AUXI-
I
Auxiliary MIC input signal -
20
AUXI+
I
Auxiliary MIC input signal +
21
AGND
GND
Analog GND
22
VSPK
I
Power supply input for the internal power
amplifier of audio codec chip,
Advise to connect VBAT.
I2S
11
I2S2_CLK1
O
PD
PD
I2S2 serial clock SCLK1
24
I2S2_CLK0
O
T
T
I2S2 serial clock SCLK0 (Default: CLK0)
25
I2S2_WA0
O
T
T
I2S2 field selection signal
26
I2S2_TX
O
T
T
I2S2 serial data output
27
I2S2_RX
I
T
T
I2S2 serial data input③
USB
31
USB_DP
I/O
USB data signal+
32
USB_DM
I/O
USB data signal-
33
USB_ID
—
USB ID signal
34
VUSB
I
USB Power Input

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
18
of
44
Pin #
Pin Name
I/O
Reset
Value
Idle
Value
Description
92
USB_TEST
—
USB TEST signal
I2C
28
I2C_SDA
I/O
PU
PU
I2C data signal line, Internal 1K pull-up
resistor③
29
I2C_SCL
O
PU
PU
I2C clock signal line, Internal 1K pull-up
resistor.
UART1
35
UART1_RI
O
L
L
UART1 Ring Indicator
36
UART1_DSR
I
T
T
UART1 DTE Ready
37
UART1_DTR
O
H
H
UART1 DCE Ready
38
UART1_DCD
O
L
L
UART1 Carrier Detect
39
UART1_CTS
I
PU
PU
UART1 Clear To Send
40
UART1_RTS
O
L
L
UART1 Request To Send
41
UART1_TXD
O
PP
PP
UART1 Transmitted Data
42
UART1_RXD
I
PU
PU
UART1 Received Data
UART2
45
UART2_TXD
O
PP
PP
UART2 Transmitted Data
44
UART2_RXD
I
PU
PU
UART2 Received Data
ADC
50
ADC2
I
ADC2, input voltage range:0~1.2V
51
ADC1
I
ADC1, input voltage range:0~1.2V
EINT
56
WAKE_UP
I
PU
PU
Interrupt of external wake-up, active low.
57
EINT2
I
PU
PU
External interrupt, active low.
USB HSIC
90
HSIC_USB_DATA
HSIC USB data signal line
(not supported)
91
HSIC_USB_STRB
HSIC USB pulse signal line
(not supported)

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
19
of
44
Pin #
Pin Name
I/O
Reset
Value
Idle
Value
Description
Antenna
67
ANT_MAIN
I
Main antenna interface,impedance
requirement: 50 ohm.
71
ANT_DIV
I
Only supported by some models
Others
3
DSP_AUDIO_IN1
O
H
H
GPIO . Used for HSIC IPC in special
software versions
54
CLKOUT0
O
PP
PP
Digital audio clock output
89
SMI
O
L
Sleep Mode Indicator
86
LPG
O
Status indicator
NC
23
NC
55
NC
52
NC
53
NC
73
NC
74
NC
75
NC
76
NC
78
NC
79
NC
80
NC
81
NC
82
NC
83
NC
84
NC
85
NC
87
NC

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.
H330S Hardware User Manual Page
20
of
44
Pin #
Pin Name
I/O
Reset
Value
Idle
Value
Description
88
NC
94
NC
95
NC
96
NC
101
NC
105
NC
106
NC
107
NC
108
NC
GND
2
GND
12
GND
30
GND
43
GND
58
GND
63
GND
65
GND
66
GND
68
GND
69
GND
70
GND
72
GND
93
GND
97
GND
98
GND
99
GND
100
GND
102
GND