Fisher-Price B8869 User manual

Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for battery installation: Phillips Screwdriver (not included).
Requires four LR14 (“C”) alkaline batteries for operation (not included).
Weight Limit: 9 kg (20 lbs).
IMPORTANT! The maximum weight limit for this product is 9 kg (20 lbs).
If your child weighs less than 9 kg (20 lbs), but is really active and appears
to be able to climb out of the swing, immediately discontinue its use.
www.fisher-price.com/uk
B8869
Product features and decorations may vary from photo above.
WARNING
IMPORTANT! KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.

To prevent serious injury or death
from falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who can
sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product
on an elevated surface.
WARNING
Warnings
2

Parts
Pad with Restraint
Front Tube
Frame with Liner
3
2 Frame Tubes

2
1
• Rotate the upper frame tube until it "snaps" into an upright position,
as shown.
Assembly
4
IMPORTANT! Before assembly, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing, damaged or broken. Contact Mattel for
replacement parts and instructions if needed. Never substitute parts.
• Position the front tube so that the rubber feet are flat on the surface.
• While pressing the button on the lower frame tube, insert it into an end of the
front tube. Continue to insert the lower frame tube into the front tube until you
hear a "click".
• While pressing the button on the front tube, insert it into the end of the lower
frame tube. Continue to insert the front tube into the lower frame tube until you
hear a "click".
Upper
Frame
Tube
Rubber
Feet
Down
Press Button on
Lower Frame Tube
Press Button on
Front Tube

4
3
Assembly
5
• Position the frame with liner so that the seat is over the front tube.
• While pressing the buttons on the upper frame tubes, insert them into
the holes in the underside of the frame with liner.
• Continue to insert the upper frame tubes into the frame with liner until
you hear a "click" on both sides.
Press
Button
on Upper
Frame
Tube
Frame with
Liner
• Check to be sure the front tube is secured to the lower frame tubes.
• Pull the front tube. It should remain attached to the lower frame tubes.
If you can remove it, you have not assembled it properly. Please re-read
and repeat Assembly step 2.
Lower
Frame
Tubes
Pull
Front
Tube
Seat
Front Tube

6
5
Assembly
6
Upper
Frame
Tube
Upper
Frame
Tube
• Fit the pad seat back pocket over the seat back and fasten.
• Fit the pad seat bottom pocket over the seat bottom and fasten .
IMPORTANT! This product must always be used with the pad
provided, which includes the restraint system. Attach the provided
pad (with restraint system) to this product.
Pad Seat
Back
Pocket
Pad Seat
Bottom
Pocket
• Check to be sure the upper frame tubes are secure in the frame with liner.
If you can remove the upper frame tubes from the frame with liner, you
have not properly inserted the tubes into the frame. Remove the upper
frame tubes from the frame with liner and reread and repeat
Assembly step 4.
Frame with
Liner

Assembly
7
Slot
Slot
Waist
Belts
• Lift the edges of the pad and insert the waist belts on the liner
through the slots in the pad.
Assembly is now complete.
7

• Open the battery holder.
• Insert four LR14 ("C") alkaline batteries.
• Close the battery holder.
• Locate the battery compartment door on the frame.
• Loosen the screw in the battery compartment door with a
Phillips screwdriver.
• Remove the battery compartment door and the battery holder from
the battery compartment.
Battery Installation
Battery
Holder
8
Battery
Compartment
Door
Battery
Holder
Hint: We recommend using alkaline batteries for longer battery life.

Battery Installation
• Align the ridge on the battery holder with the groove in the
battery compartment.
• Slide the battery holder back into the battery compartment.
• Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
Battery
Holder Battery
Compartment
Door
9
IMPORTANT! Low battery power may cause this product to
operate erratically (no sounds/lights/movement) and the product
may not turn off. Remove and throw away all four batteries and
replace with four, new “C” (LR14) alkaline batteries.

Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause
a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery holder.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of batteries in a fire. The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.
10
1.5V x 4
LR14 ("C")
SHOWN ACTUAL SIZE