Fisher-Price Side-to-side BMK11 User manual

1
BMK11
fisher-price.com
Side-to-side
Head-to-toe
IMPORTANT! Please keep these instructions for future reference.
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips screwdriver (not included).
Requires four D (LR20) alkaline batteries and two AAA (LR03) alkaline batteries for
operation (batteries not included).
Product features and decorations may vary from photographs.

2
©2013 Mattel. All Rights Reserved.
PRINTED IN CHINA BMK11pr-0920
UNITED STATES
1-800-432-5437. Fisher-Price, Inc.,
636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers:
1-800-382-7470.
• Press the buttons on each hub and push
the bases together for storage.
• Lean the swing frame against a wall
for storage.
• To remove the pad, unbuckle the restraint
system and the straps under the seat. Pull to
remove the pad.
• Machine wash the pad in cold water with
a mild detergent. Do not use bleach. Tumble
dry on low heat and remove promptly.
• To clean the frame, restraint system and
toys, use a mild cleaning agent and damp
cloth. Rinse with clean water to
remove residue.
• To replace the pad, follow the
assembly instructions.
• Periodically check the swing for loose
fasteners or broken parts and tighten
as needed.
PRESS
PRESS
PRESS
PRESS
Storage & Care
IMPORTANT! Remove the batteries for
long-term storage.
Consumer Information

3
Consumer Information
WARNING
Prevent serious injury or death from falls or strangling in the
restraint system:
• Never leave child unattended.
• This product is not intended to replace a crib or bassinet for prolonged
periods of sleep.
• Always use the restraint system.
• Discontinue use when an active child attempts to climb out.
• Never use on any elevated surface. Use only on a floor.
IMPORTANT! The weight limit for this product is 25 lb (11,3 kg). If your child weighs less
than 25 lb (11,3 kg), but is really active and appears to be able to climb out of the swing,
immediately discontinue its use.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or
broken. Contact Fisher-Price®for replacement parts and instructions if needed. Never
substitute parts.
• This product comes with replacement warning labels which you can apply over the
factory applied warning label if English is not your primary language. Select the warning
label with the appropriate language for you.
• Este producto viene con etiquetas de advertencia en español que puede pegar sobre las
etiquetas de fábrica, en caso de que el inglés no sea su idioma primario. Seleccione las
etiquetas de advertencia en el idioma de su elección.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.

4
Parts
Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the pad.
2 Hubs
Seat Bottom
2 Bases
Handle
Seat Pad
Seat Back
Seat Base
#8 x ¾" (1,9 cm) Screw - 4 M5 x 31 mm Screw – 4
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
Seat Pad
StB

5
Assembly
1
• Fit the tubes on the hubs into the tubes on the bases.
Hint: When assembled properly, the hub arms should face each other.
Hub Arms
Bases
• Fit the seat bottom onto the seat base.
Hint: The seat bottom is designed to fit onto the seat base one way. If it does not seem to
fit, turn it around and try again.
• Insert two #8 x ¾" (1,9 cm) screws into the seat bottom and tighten.
2
Seat Bottom
Seat Base

6
Assembly
3
• Fit the seat back onto the seat base.
Hint: The seat back is designed to fit onto the seat base one way. If it does not seem to fit,
turn it around and try again.
• Insert two #8 x ¾" (1,9 cm) screws into the seat back and tighten.
Seat Back
• Turn the seat assembly sideways.
• Fit the seat assembly tubes up into the sockets in the hub arms.
Hint: The seat assembly is designed to fit one way. If it does not seem to fit, turn it around
and try again.
4
Hub Arms

7
Assembly
• Insert an M5 x 31 mm screw into each hub arm and tighten.
5
• Fit the ends of the handle into the socket in each hub.
• Insert an M5 x 31 mm screw into each hub and tighten.
6
Handle

8
Assembly
7
• Insert the waist belts through the lowest slots in the seat pad. Make sure the waist belts
are not twisted.
Smaller Baby
• Insert the ends of the shoulder belts through the lower slots in the seat pad back. Make
sure the shoulder belts are not twisted.
8Shoulder Belts
Lower Slots
LOWER SLOTS
Waist Belts
LOWEST SLOTS

9
Assembly
Larger Baby
• Insert the ends of the shoulder belts through the upper slots in the seat pad back. Make
sure the shoulder belts are not twisted.
9Shoulder Belts
Upper Slots
UPPER SLOTS
10
• Fit the pad edges around the rim of the seat.

10
Assembly
11
• Fasten the buckles on the front of the seat pad to the buckles on the seat bottom. Make
sure you hear a “click”.