Fisher-Price 73397 User manual

Instructions
Model Number 73397
Stand-Up Ball Blast
™
• Please keep this instruction sheet for future reference, as it contains important information.
• Adult assembly is required.
• Requires three “AA” batteries for operation (included).
• Tool required for assembly: Short-shaft Phillips screwdriver (not included).
™
w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m

Parts
Electronic Top
Base
Base
Dimple
Bottom Track
Bottom Track
5 Balls
4 Feet
Track 3
Center Tube
(2 Pieces)
Assembly
2
1
Tab
Foot
Peg
Hole
Hole
#6 x 1 /2"-9
#6 x 1"- 8
Screws Shown
Actual Size
Track 2
Track 1
2
Decorative label sheet not shown.
This product contains small parts in its
unassembled state. Adult assembly is required.
CAUTION
• Place the base upside down on a flat surface.
• Identify the side of the bottom track with the dimple.
• Place the bottom track onto the pegs on the base with the
dimpled side facing you.
• Insert the tabs on on each edge of a foot under the edge of
the base so that you can fit the pegs on the foot into the holes
on the bottom track.

Center
Tube Piece
• Insert and “snap” the tabs on one of the center tube pieces
into the slots in the other center tube piece.
6
4
3
Bottom Track
Front Holes
Do Not
Insert the
1" Screws
Here
Center
Tube Piece
3
PUSH
• Insert two #6 x 1/2" screws through the remaining two holes
in the foot and into the base, as shown.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Repeat steps 2 through 5 to attach the other three feet.
• Turn the base over.
• Insert two #6 x 1" screws through the front holes in the foot
and into the base, as shown.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Push down in the center of the foot to “snap” it into place.
• Be sure the tabs are under the edge of the base and the
pegs fit snuggly in the holes on the bottom track.
#6 x 1"- Screw
Shown Actual Size
5
#6 x 1/2"- Screw
Shown Actual Size

4
• Position track 2 with the grooved side up. Fit track 2 onto
the center tube.
• Rotate track 2 counter-clockwise until it meets track 1. Insert
and “snap” the tab on the end of track 2 into the slot in
track 1. Be sure the peg on the end of track 2 fits into the
hole in track 1.
• Repeat this process to assemble track 3 to track 2.
Hint: When the tracks are properly fitted on the center tube,
a tab on the center tube should be visible above each track.
9
Track 2
Track 1
Center Tube
• Align the smallest tab on the center tube with the smallest
slot in the base. Push down on the track support to “snap”
the center tube into place.
Base
• Locate track 1. Position track 1 with the grooved side up.
• Fit track 1 onto the center tube. Rotate it counter-clockwise
until it reaches the base.
• Insert and “snap” the tab on the end of track 1 into the slot
in the base.
8
Center Tube
Track 1
Tab
7
Base Slot
Tab
Peg
Hole
Center Tube
Small Tab
Base Small Slot
PUSH
PUSH
• Insert a #6 x 1/2"screw through the hole in track 3 and into
the tube. Tighten the screw with a Phillips screwdriver.
Do not over-tighten
10
Track 3
Center
Tube
#6 x 1/2"- Screw
Shown Actual Size

• Match the ribbed tab on the center tube with the grooved
slot in the electronic top.
• Push down on the electronic top to “snap” it into place. Pull
up on the electronic top to be sure it is secure.
11
Electronic
Top
Center Tube
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied are
clean and dry. Wipe this product with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, do not attempt to apply a label more
than once.
• Apply the labels as shown in the illustration above.
Decoration
Proper label application will help to keep the
labels looking their best!
Volume
Switch
5
Rib
Groove

Lights and Sounds Fun! Battery Replacement
Volume Switch
• Locate the volume switch on underside of the electronic top.
• Slide the switch to the desired position: Off , On with low
volume or On with higher volume .
• For flashing lights and lively music, baby can place the ball
in any one of the three openings or center hole on the top of
the toy and push it through.
• Place the ball in the center hole. Press the play button to
drop the ball.
For best performance, we recommend replacing
the batteries that came with this toy with three,
new alkaline “AA” (LR6) batteries.
Electronic Top
Battery
Compartment
SHOWN ACTUAL SIZE
• Locate the battery compartment on the underside of
electronic top.
• Loosen the screws in the battery compartment door with a
short shaft Phillips screwdriver and remove the door.
• Carefully remove the exhausted batteries from the battery
compartment. Properly discard the batteries.
• Insert three, new, “AA” (LR6) alkaline batteries as
indicated inside the battery compartment.
• Replace the battery compartment door and tighten the
screws with a Phillips screwdriver. Do not over-tighten.
1.5V x 3
“AA” (LR6)
Play Button
Ball
Electronic Top
BOTTOM VIEW
6

Battery ips Care
Wipe this toy with a clean cloth dampened with a mild soap
and water solution. Do not immerse this toy.
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use.
Always remove exhausted batteries from the toy. Battery
leakage and corrosion can damage this toy. Dispose of
batteries safely.
• Do not dispose of batteries in a fire. The batteries may
explode or leak.
• Never short-circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as
recommended in the Battery Replacement instructions are
to be used.
• If removable rechargeable batteries are used, they are only
to be charged under adult supervision.
• Rechargeable batteries are to be removed from the toy
before they are charged.
• If you use a battery charger, it should be examined regu-
larly for damage to the cord, plug, enclosure and other
parts. Do not use a damaged battery charger until it has
been properly repaired.
• When sounds from the toy become faint or stop, it’s time
for an adult to change the batteries!
7

FCC Note (United States Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION: Changes or modifications not expressly approved
by the manufacturer responsible for compliance could void
the user's authority to operate the equipment.
Consumer Information
Questions? We’d like to hear from you!
Call Fisher-Price®Consumer Relations, toll-free at
1-800-432-KIDS, 8 AM – 6 PM EST Monday through
Friday. Hearing-impaired consumers using TTY/TTD
equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Relations
636 Girard Avenue
East Aurora, New York 14052.
For other countries, outside the United States:
Canada: Call 1-800-567-7724, or write to: Mattel Canada Inc.,
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia:Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. Printed in Mexico
©2001 Mattel, Inc. All Right Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. 73397c-0920