Fisher-Price Caring Touch Nursery Center 71778 User manual

Instructions
Caring Touch™
Nursery Center
Model Number: 71778
Dolls and blanket not included.
Please keep these instructions for future reference.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver.
If you experience a problem with this product, or are missing a part,
please call us at 1-800-432-KIDS, rather than return this product to the store.

Parts
Message to Parents
CAUTION
2
Please keep small parts and plastic
bags out of children’s reach. Dispose of
plastic bags properly.
BOTH SHOWN
ACTUAL SIZE
Thank you for purchasing the Fisher-Price®Caring Touch™ Nursery Center. With the Caring Touch™ Nursery Center,
your make-believe mommy or daddy has everything needed to care for baby. Wash baby in the pretend basin and then
flip the cover to put on a fresh diaper (diaper not included). Put baby in the cradle and rock baby to sleep. Sweet dreams
are ahead for baby with your child's caring touch!
If you experience a problem with this product, or are missing a part, please call us at 1-800-432-KIDS, rather than
return this product to the store.
Cream Jar
Cover
Sprayer
Mobile
Mobile Arm
Plug
Cover
Cradle
Sleeve Sleeve
Headboard
Side
Panel B
Side
Panel A
Basin
Basin Base
Cradle Base
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Before assembling the Caring Touch™ Nursery Center,
please wipe each part with a clean, dry cloth.
#10 x 13/4" Screw
with 1/2" Washer - 2
#8 x 3/4" Screw - 6

3
• Position the headboard so that the tabs face the basin.
• Insert and snap the headboard into the slots in the
base assembly.
• Gently pull up on the headboard to be sure it is secure.
4
Basin Assembly
Base Assembly
Side
Panels
Tabs
Slots
Slots
Base Assembly
Basin
Tabs
Headboard
Assembly
1
• Turn the basin base upside down on a flat surface.
• Turn the cradle base upside down and fit it onto the
basin base.
• Insert two 3/4" screws through the cradle base and
into the basin base. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
• Set the base assembly aside.
• Turn the basin upside down on a flat surface.
• Fit the side panel labeled A to the side of the basin.
• Insert two 3/4" screws through side panel A and into the
basin. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Fit the side panel labeled B to the side of the basin.
• Insert two 3/4" screws through side panel B and into the
basin. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
2
3
Cradle Base
Basin
Base
Side
Panel B
Side
Panel A
Basin
• Turn the base assembly and basin assembly upright.
• Insert and snap the tabs on the basin assembly side
panels into the slots in the base assembly.
• Gently pull up on the basin assembly to be sure it is
secure.

• While holding the cradle in place, insert a sleeve into
the outside hole in the foot of the cradle.
• Insert a 13/4" screw with 1/2" washer through the inside
hole in the foot of the cradle and into the basin. Hand-
tighten the screw.
• Tighten the screw in the foot of the cradle and the head-
board with a Phillips screwdriver. Do not over-tighten.
6
• Insert a sleeve into the inside hole in the headboard.
• Position the cradle so that the quilted side is toward
the basin.
• While holding the cradle in place, insert a 13/4" screw
with 1/2" washer through the outside hole in the head-
board and into the cradle. Hand-tighten the screw.
4
Assembly
Cradle
Basin
Headboard
Sleeve
Sleeve
Cradle
Basin
Screw
Cradle Foot of
Cradle
Screw
Headboard
Basin
Quilted Side
5
• Check to be sure the cradle swings freely. If the cradle
does not swing freely, loosen the screw in the foot of
the cradle and the headboard 1/4turn with a Phillips
screwdriver. Again, check to be sure the cradle swings
freely, and loosen if necessary.
Cradle

• Position the cover with the quilted side facing away
from the basin.
• Fit the back peg on the cover into the back slot in the
basin.
• Insert and snap the front peg on the cover into the
front slot in the basin.
• Position the mobile so that the arched side is up.
• Make sure the areas where the labels will be applied
are clean and dry.
• Apply the labels as indicated in the illustration.
• For best adhesion, try to avoid applying the labels
more than once.
Assembly
Cover
Back Slot
Front Slot
Front
Peg
Back
Peg
Basin
1
5
2
4
3
• Insert and snap the mobile arm into the slot in the top
of the headboard.
• Insert the plug into the top of the mobile arm.
• Position the mobile so that the label side is toward
the plug.
• Fit and snap the mobile onto the end of the plug.
5
Mobile
Mobile
Label Side
Mobile Arm
Mobile Arm
Plug
Headboard
Slot

Assembly
• Fit the cream jar cover onto the cream jar.
• Insert the sprayer into the hole in the basin.
Assembly is now complete.
Care
Questions?
• To clean or remove static electricity, wash all parts with
a mild cleaning agent and damp cloth. Do not use
bleach. Rinse with clean water to remove residue.
• Periodically check the Caring Touch™ Nursery Center
for loose fasteners and tighten as needed.
If you have any questions about this product: In Canada, call 1-800-567-7724, or write to: Mattel/Fisher-Price, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone]. In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to: Fisher-Price,
Mattel Pty. Limited, 461 Plummer Street, Port Melbourne, Victoria 3207.
©1997 Fisher-Price, Inc., East Aurora, New York 14052
Printed in U.S.A. 71778 1 71778-0920
We'd like to hear from you!
Call Fisher-Price®Consumer Affairs, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through
Friday. Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Affairs, 636 Girard Avenue,
East Aurora, New York 14052.
Sprayer
Hole
Cream
Jar
Cream Jar
Cover