Fisher-Price BFL54 User manual

BFL54
Please keep this instruction sheet for future reference,
as it contains important information.
Requires six AA batteries (included).
Batteries included are for demonstration purposes only.
Battery installation is required. Only adults should install batteries.
Adult setup is required to attach this toy to a crib.
Tool required for battery replacement: Phillips screwdriver (not included).
To clean, wipe the surface of this toy with a damp cloth. Do not immerse this toy.
This toy has no consumer serviceable parts. Please do not take this toy apart.
fisher-price.com

• Loosen the screws in the battery compartment
door with a Phillips screwdriver and remove
the door.
• Remove the exhausted batteries and
discard properly.
• Insert six AA (LR6) alkaline batteries.
• Replace the battery compartment door and tighten
the screws. Do not over-tighten.
• If sounds, lights or motions become faint or stop,
it's time for an adult to change the batteries.
• If the toy begins to operate erratically, you
may need to reset the electronics. Slide the
power/volume switch off and then back on.
Battery Safety Information
In exceptional circumstances, batteries may leak
fluids that can cause a chemical burn injury or ruin
your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of
different types: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods of non-use.
Always remove exhausted batteries from the
product. Dispose of batteries safely. Do not
dispose of product in a fire. The batteries inside
may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they
are only to be charged under adult supervision.
1,5V x 6
AA (LR6)
Battery Replacement Crib Attachment
WARNING
IMPORTANT! Always attach all provided fasteners
(strings, straps, clamps, etc.) tightly to a crib
or playpen according to the instructions.
Check frequently.
• Position the toy inside the crib. Make sure the
attachment strap is on the outside of the crib A.
• Slide the end of the attachment strap down
through the slot on the back of the toy B.
• Pull the end of the attachment strap up and fasten
to the peg on the back of the toy C.
Note: This toy should be snug against the crib rail
and spindles. Use the strap slot that provides the
tightest fit.
• If you have excess strap, slide the free end of the
attachment strap up through the opening near the
top of the attachment strap D.
Prevent Entanglement Injury
• This product may not attach
to all crib designs. Do not add
additional strings or straps to
attach to a crib or playpen.
• Use ONLY attached to a crib.
C
A
D
B
1
For longer life, use
alkaline batteries.

Mattess
Mattess
Bottom
Bottom
of Toy
of Toy
At Least
At Least
7 Inches (18 cm)
7 Inches (18 cm)
3
• Make sure the distance between the bottom of
the toy and the crib mattress is at least 7 inches
(18 cm).
• If the distance is less than 7 inches (18 cm):
readjust the attachment strap to lift the product;
or lower the crib mattress.
• Tie the toy’s strings to a crib spindle.
Note: It is better to tie the strings in a knot than
a bow, since a bow may be easily untied.
Crib Attachment 3 Soothing Modes
2
Press to start/
Press to start/
restart or change
restart or change
the music/sounds/
the music/sounds/
lights/motion!
lights/motion!
Power/Volume
Switch
Sounds
Select Button
Mode Switch
• Slide the mode switch to music,
motion & lights ; music & motion ;
or music only .
• Slide the power/volume switch to ON with low
volume , ON with high volume or OFF .
• Press the sounds select button once for soothing
lullabies ; press again for nature sounds ;
press again for white noise .

• Protect the environment by not disposing
of this product with household waste
(2002/96/EC). Check your local authority
for recycling advice and facilities.
ICES-003
This Class B digital apparatus complies with
Canadian ICES-003. Operation is subject to the
following two conditions: (1) this device may not
cause harmful interference and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada. L’utilisation de ce
dispositif est autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
Consumer Information
CO
N
SU
MER A
SS
I
S
TAN
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
©2014 Mattel. All Rights Reserved.
PRINTED IN CHINA BFL54pr-0920
FCC Statement (United States Only)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
Note: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment. This device complies with
Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may
not cause harmful interference and (2) this device
must accept any interference received, including
interference that may cause undesired operation.