Fisher-Price R4747 User manual

www.fisher-price.com
R4747
www.fisher-price.com

2
WARNING
Prevent Entanglement Injury
• Keep mobile out of baby’s reach.
• Remove mobile portion of product from crib or playpen when baby
begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add additional
strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib.
Consumer Information
Please keep this instruction sheet for future reference, as it contains•
important information.
Requires three "C" (LR14)• alkaline batteries (not included) for operation.
Adult assembly is required.•
Tool required for assembly: Phillips screwdriver (not included).•
• The mobile portion of this product may be used from birth until 5 months.
• The base portion of this product may be used from birth until 36 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
• Always attach with all provided fasteners tightly to a crib or playpen according to the
instructions. Check frequently.
• Wipe this toy with a clean cloth dampened with a mild soap and water solution.
Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take this toy apart.

3
Assembled Parts
Base
Mobile
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen
all screws with a Phillips screwdriver. Do not over-tighten.
Arm
Crib Connector

4
• Protect the environment by not disposing of this product with household
waste (2002/96/EC). Check your local authority for recycling advice and
facilities (Europe only).
• Locate the battery compartment on the back of the base.
• Loosen the screws in the battery compartment door and lift to remove it.
• Insert three "C" (LR14) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically you may need to reset the electronics. Slide
the power/volume switch off and then back on.
• When sounds or motion become faint or stop, it's time for an adult to change the batteries.
Battery Installation
1.5V x 3
"C" (LR14)

5
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
Battery Safety Information
ICES-003
NMB-003
This Class B digital apparatus complies with Canadian ICES-003.•
Operation is subject to the following two conditions: (1) this device may not cause•
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.•
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne•
doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter
tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.

6
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CO
N
SU
MER A
SS
I
S
TAN
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. R4747pr-0920
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA

7
Assembly
Crib Connector
• Fit the crib connector to the base, as shown.•
IMPORTANT! Make sure the straps are over the top of the crib connector.
• Tighten both screws in the crib connector.
• First press the button next to the socket in the base
and then slide the socket door open .
• Fit the arm into the socket in the base.
• Tighten both screws in the arm.
Base
PRESS
PRESS
SLIDE
SLIDE
1
2
Socket
Arm

8
Assembly
• Fit the mobile socket onto the retainer on the end of the arm.
• Tighten both screws in the mobile to secure it to the arm.
Retainer
Mobile Socket
3

9
Straps
Crib Attachment
Base Crib Top Rail
• Position the base so that the decorated side faces inside the crib.
• Fit the base onto the crib top rail, as shown.
• Make sure the top strap is hanging over the crib top rail. Position the bottom strap
through the crib rails.
• Buckle the straps. Make sure you hear a "click". Pull on both ends of the strap to be
sure it is secure.
• Make sure the straps are tightened securely around the crib top rail. Pull the free end
of the strap to tighten.
Hint: You can secure the free end of the strap to the base. Simply fit the free end of
the strap under the tabs.
Straps
Straps
1
2
Tab Tab

10
• Tie the base strings to a crib spindle.
Note: It is better to tie the strings in a knot than a bow, since a bow may be easily untied.
Crib Attachment
At Least 7 Inches (18 cm)
At Least 7 Inches (18 cm)
• If the distance between the base and the mattress is less than 7 inches (18 cm),
lower the crib mattress.
4
3