Fisher-Price Spark Art Easel K0026 User manual

1
www.fisher-price.com
K0026
Creativity System™

Consumer Information
• Please keep this instruction sheet for future reference, as it
contains important information.
• Requires three ”AA” (LR6) alkaline batteries (not included)
for operation.
• Adult assembly is required. Tool needed for assembly:
Phillips screwdriver (not included).
• This product contains magnets. Do not use around items
that are sensitive to or affected by magnetic fields.
• Wipe this toy with a clean cloth dampened with a mild soap
and water solution. Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take
this toy apart.
2
WARNING
Warning - Choking Hazard
Not recommended for children under
3 years because it contains small
parts that can be swallowed.
www.service.fisher-price.com
Call our Consumer Relations Department, toll-free at
1-800-432-5437, 9 AM - 7 PM EST Monday through Friday
and 11 AM - 5 PM EST Saturday. Hearing-impaired consumers
using TTY/TDD equipment, please call 1-800-382-7470.
Write to us at: Fisher-Price®Consumer Relations,
636 Girard Avenue, East Aurora, New York 14052
Tips
• The Inspiration Pod with Pen works with the accessories
wherever you go. Clip the Inspiration Pod to your belt or
carry it along.
• We recommend that your child uses markers or other
drawing tools in the dominant hand and the Inspiration
Pen in the other hand.
• For best results, keep tip of the pen clean.
Installing Chips (sold separately)
into your Inspiration Pod
• Spark Art Creativity System™Easel accessories (sold
separately) include an Inspiration Chip. To install the
Inspiration Chip, loosen the screws in the Inspiration Pod
battery compartment door. Remove the door.
• Press the Inspiration Chip into one of the slots inside the
Pod, as shown.
Hint: You can insert up to six Inspiration Chips inside the
Inspiration Pod.
• Replace the door and tighten the screws.

3
2 Clips
#6 x 3/4"(1.9 cm)Chrome Screw – 21
(Assembly steps 1, 4, 8, 10, 12 and 16)
#8 x 1"(2.5 cm)Gold Tone Screw – 10
(Assembly steps 5, 7 and 14)
Both Shown Actual Size
Note: Tighten and loosen all screws with a
Phillips screwdriver. Do not over-tighten.
Easel Board
Storage Tray
2 Accessory Bins
Brace
2 Legs
Parts
Cap
2 Handles
Back Panel
Inspiration Pod
with Pen
Parts Not Shown
6 Dry-Erase Markers
2 Scene Starter Backgrounds
5 Color-By-Sound Activity Pages*
12 Magic-Sound Magnets
2 Magic-Sound 3D Models
* Additional color-by-sound activity
pages sold separately and subject
to availability.
Artist’s Tray

4
• Place the easel board face down.
• Fit the handles to the grooves in each side of the
easel board.
• Insert two #6 x 3/4” chrome screws into each handle
and tighten.
Assembly
Handles
Easel Board
• Turn the easel board upright.
• “Snap” both clips to the front side of the easel board.
Clips
12
• Position the storage tray between the legs, as shown.
• Fit the pegs on the storage tray into the holes in the legs.
• Insert two #8 x 1” gold tone screws through each leg and
into the storage tray. Tighten the screws.
Legs
• Fit the pegs on the artist’s tray into the holes in the legs.
Artist’s Tray
56
Storage Tray

5
Assembly
• First, insert two #8 x 1” gold tone screws through each leg
and into the artist’s tray. Tighten the screws.
7
• Then, insert two #6 x 3/4” chrome screws through the
artist’s tray and into each leg. Tighten the screws.
8
• Fit the cap to the top of the easel board.
• Make sure the tab on each end of the cap fits into the slots
in the top of the easel board.
Cap
• Place the easel board face down again.
• Insert five #6 x 3/4” chrome screws into the easel board
and tighten.
• Set the easel board assembly aside.
34

6
Assembly
• Position the easel board upright.
• Fit the easel board to the brackets.
• Insert two #6 x 3/4” chrome screws into each bracket
and tighten.
Bracket
Easel Board
Bracket
10
• Press the button on each leg A.
• Grasp the column inside each leg and lift to the highest
position B.
• While holding the columns in place, turn the brackets until
they “click” into position C.
Press
Press
Button
Button
Lift
Lift
Column
Column
A
B
Lift
Lift
Column
Column
B
Press
Button
A
9
C
CTurn
Brackets
Press
Button
Lift
Column
Lift
Column
• Insert two #8 x 1” gold tone screws though each leg and into
the brace. Tighten the screws.
14
• With the ribbed side facing you, fit the brace to the legs.
Brace
13

7
Assembly
• Fit the hooked tab on each accessory bin into the slot in
each leg.
Slot
• Insert two #6 x 3/4” chrome screws into the artist’s tray and
each accessory bin. Tighten the screws.
Accessory
Bin
Accessory
Bin
Hooked
Tab
15 16
• Position the back panel with ribbed side facing you and the
tabs at the top.
• First, fit the bottom edge of the back panel into the slot in the
legs A. Then, fit the back panel tabs onto the columns B.
Back Panel
A
A
B
• Insert four #6 x 3/4” chrome screws into the back panel
and tighten.
11 12
Tabs

8
Battery Installation Battery Safety Information
• Loosen the screws in the battery compartment door with a
Phillips screwdriver. Remove the battery compartment door.
• Insert three “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten
the screws.
• When sounds become faint or stop, it's time for an adult to
change the batteries!
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To
avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the toy. Dispose of
batteries safely. Do not dispose of the product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as
recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
• Protect the environment by not disposing of this
product with household waste (2002/96/EC). Check
your local authority for recycling advice and facilities
(Europe only).
Convert from Easel
to Creativity Table
• Fit your hands through the handles and squeeze the release
levers A.
• Turn the easel board down B.
• Lift the easel board slightly Cand then lower it completely D.
4
3
A
B
C
D
1.5V x 3
"AA" (LR6)
Inspiration Pod
Convert from
Creativity Table to Easel
• Fit your hands through the handles and press and hold both
buttons under the easel board A.
• Lift and turn the easel board until it “clicks” into the highest
position B.
A
B

9
Notes About
Dry-Erase Markers
• Use only the dry-erase washable markers that came with
this toy.
• Dampen a soft cloth with water and wipe to clean the easel
board or backgrounds.
IMPORTANT!
• To completely remove marker residue from the easel board or
backgrounds, dampen the eraser and wipe after each use.
• Markers conform to ASTM D4236. Avoid contact with carpet,
clothing, walls and furniture. Do not use permanent markers
on the easel surface or dry-erase accessories. Recap
markers after use. Adult supervision is recommended.
• To remove marker from the skin, simply use soap and water.
United States Only
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
FCC Statement
Easel Height Adjustment
• Fit your hands through the handles and squeeze the
release levers A.
• Lift the easel board Band let go of the release levers.
• Lower the easel board until it “clicks” into the middle height
position Cor the lowest height position D.
• To raise the easel board to a higher position again, simply
lift until it “clicks” into place.
A
B
C
D
Easel Adjusts to Three Different Heights!

Spark Imagination a
n
Use the Inspiration Pen on the easel, scene starter back
g
color-by-sound activity pages to reveal interactive voice pr
o
10
Repeat Last Sound
Adjust Volume
Select to hear draw-
ing suggestions.
Colors
Sounds
Objects
Slide the power switch
on or off .
Use the tip of the
pen to adjust volume
higher or lower.
Use the tip of the pen to “read” areas or objects
on scene starter backgrounds , magic-sound
magnets or magic-sound 3D models .
Create - Listen to fun sound effects.
Discover - Listen to items identified.
Use the tip of the pen to “read” areas or
objects on color-by-sound activity pages.
Create - Listen to coloring sug-
gestions or fun sound effects.
Discover - Listen to fun sound effects.
Note about color-by-sound activity pages: These pages
contain hidden codes that cannot be seen by copiers. Only
the original pages can be “read” by the Inspiration Pen.
Optical reader technology lets
the Inspiration Pen “read” hidden
codes on dry-erase scene starter
backgrounds and more!