Fisher-Price Y6965 User manual

1
Y6965
Y6965
BMD91
BMD91
fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three AA (LR6) alkaline batteries (not included) for operation.
Adult assembly is required. Tool required: Phillips screwdriver (not included).
Wipe this toy with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.

2
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications
not expressly approved by the
manufacturer responsible for
compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
ICES-003
This Class B digital apparatus complies
with Canadian ICES-003. Operation is
subject to the following two conditions:
(1) this device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
NMB-003
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada. L’utilisation de ce dispositif
est autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du
dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même
si ce brouillage est susceptible de
compromettre le fonctionnement
du dispositif.
CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
©2013 Mattel. All Rights Reserved.
PRINTED IN MEXICO Y6965b-0920

3
Assembled Parts
2 Rear Fenders Rear Wheel Base Windshield
Side Base
Side Panel
(outside)
Dash Trunk
Side Panel
(inside)
Roller Assembly
Door
Front End
Dash
Side Panel
Part not shown: Label Sheet
#8 x ¾" (1,9 cm) Screw – 21
SHOWN ACTUAL SIZE
Tighten all screws with a Phillips
screwdriver. Do not over-tighten.
This package contains small
parts. For adult assembly only.
CAUTION
Sid P l

4
Assembly
y
1
2
• Fit the rear fenders onto the rear wheel base. Push to “snap” each rear fender
in place.
Hint: Each rear fender is designed to fit one way. If it does not seem to fit, try the
other rear fender.
Rear
Fenders
Rear Wheel Base
• Fit the trunk into the slots in the rear wheel base. Push to “snap” into place.
Trunk

5
3
4
• Fit the tabs on the roller assembly into the slots in the trunk.
• Insert two screws into the roller assembly and tighten.
• Fit the side panels onto the front and rear ends.
Roller
Assembly
Side Panel
(outside)
Side Panel
(inside)
Front End
Assembly

6
Assembly
5
6
y
• Insert nine screws into the side panel and tighten.
• Carefully turn the car assembly over.
• Fit the side base to the front and rear end of the car assembly.
Side Base
BOTTOM VIEW

7
• Turn the car assembly upright.
• Fit the peg on the door into the hole in the car. Push to “snap” in place.
Door Peg
Assembly
• Insert six screws into the side base and tighten.
7
8

8
Assembly
IMPORTANT! Apply labels 7 and 8 to windshield before completing the next step.
• Apply labels exactly as shown in the illustration. Avoid repositioning a label after
it has been applied.
plie
d.
• Fit the windshield onto the dash and push to “snap” in place.
9
10
11
• Fit the windshield on the dash into the slot in the front end.
87
Windshield
Dash

9
Assembly
• Carefully turn the car assembly over.
• Insert four screws into front end and tighten.
BOTTOM VIEW
12
12
6
Decoration
Apply labels exactly as shown in illustrations. Avoid repositioning
a label after it has been applied.
FRONT VIEW

10
510
7
934
Decoration
LEFT SIDE VIEW
RIGHT SIDE VIEW