Flexispot 9127 User manual

INSTRUCTION MANUAL
MODEL:9127

PACKAGE LIST
2
A
E
BCD
F G H
①② ③ ④
⑤⑥ ⑦
Casters
Quantity:5
Star Base
Quantity:1
Gas Lift
Quantity:1
Seat Cushion
Quantity:1
Seat Plate
Quantity:1
Quantity:1
Back Cushion
Quantity:1 Armrests Quantity:2
Steel Plate
Quantity:3
Bolts M8x20mm Bolts M6x25mm Bolts M6x30mm Bolts M8x45mm
Quantity:4
Quantity:1
Quantity:4 Quantity:4
Quantity:4 Quantity:4 T-Wrench
Plastic CapsSpacer
Left Right

3
ASSEMBLY INSTRUCTIONS
STEP 1 : Turn the Star Base upside down, then press the Casters into
the holes at the end of each base leg.
STEP 2 : Turn the Star Base upright and insert the Lift into the center
hole of the Star Base.
B
A
C

STEP 3:Align the seat plate to the bottom of the seat cushion, make
sure that the front of the seat plate is facing the front of the seat cush
ion Attach the seat plate to the seat cushion using four M6X25mm bo
lts,tighten all the bolts with the T-wrench.
⑦
②
⑤
F
D
4
STEP 4 : Attach the Steel Plate to the seat cushion with three M8x20mm
Bolts.
⑦
①
E
Note: Do not tighten the bolts fully.

5
STEP 5:Turn the seat cushion upright and align the center hole of the
seat plate over the lift, then push the seat cushion down onto the lift
firmly until the connection is secure.
STEP 6:Attach the Steel Plate to the back cushion with four M6x30mm
Bolts.
G
③⑦

6
STEP 8:Tighten all the screws that are not tightened.
STEP 7:Attach armrest to the connector with M8*45mm Bolts on both
sides, using the T-Wrench，Then tighten all the screws ，Finally Press
the plastic caps into the adjuster holes to cover the bolts.
④⑦
⑥
⑦
①
(100%)

7

8
INSTRUCTIONS FOR USE
1.Seat Height:Paddle-shaped lever on the right side
To raise
while taking your weight off chair，
lift lever up.
To lower
while seated,lift lever up.
To increase tension:
while seated,turn knob forward
(toward+sign).
To decrease tension:
while seated,turn knob
backward(toward-sign).
2.Tilt Tension: Long stem under the seat cushion with knob
*At the proper height,your feet should rest flat on the floor.
*set the tilt tension to control the resistance you feel when leaning back.

9
INSTRUCTIONS FOR USE
*At the proper height,your feet should rest flat on the floor.
3.Operating the tilt lockout.
To let your chair tilt back,pull
the control handle out.
To stop your chair from tilting,
sit forward,then push the
control handle in.
Pull the lever FULLY and lean
back slowly until desired angle
is achieved,then slowly return
the lever to its starting position
Ensure the lever locks back in
place.
4.Backrest Recline

10
INSTRUCTIONS FOR USE
*At the proper height,your feet should rest flat on the floor.
5.Relax with footrest
Pull out the pole of the
footrest,and turn the
footrest to the front.

11

promises to repair or replace any chair that is found to be defective in
material or workmanship within one (1) and year from the date of orig
inal purchase so long as you,the original purchaser,still owns it. This is
your sole and exclusive remedy.This warranty is subject to the provisio
ns below
12

13