Fly Products Thrust User manual

VERSION 1.1 – 01/2013
© Copyright by FLY Products s.r.l.
Via Perù n. 30
63013 GROTTAMMARE (AP) - ITALY
tel./fax [phone]
www.flyproducts.com - [email protected]
ASSEMBLY MANUAL

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
2
INDEX
1 FRAME ASSEMBLY
2HARNESS SIZE ADJUSTMENT
3 FITTING THE HARNESS HIGH ATTACK
4
FITTING THE HARNESS LOW ACTIVE ATTACK (ACTIVE
LOW HANG POINT) OPTIONAL
5
FITTING THE HARNESS FIXED (FIXED HANG POINT)
OPTIONAL
6 PROP MOUNTING
7 MULTIFUNCTION HANDGRIP
8 WARRANTY

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
3
Photo frame Assembly common to paramotors: Thrust, Race c, Kompress, Sprint,
Jet.
• Step 1: assembling the outer frame
Supports
Starter manual section
(only manual starter)
Support Assembly
Step 2: Assembling the top section of the external frame
Assemble the two semicircles
Assemble the cage from top
grafts
Continue side grafting over
and then the lower teeth on
each side
1 FRAME ASSEMBLY

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
4
Punto 3 : Bloccaggio dei velcri
Upper Velcro Hook network cord on both
sides
Tighten the bottom with velcro tape on both sides
Tighten the upper with velcro tape on both sides

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
5
Find the most suited to your needs and verify in the Simulator
Cut along the dotted line to get size M.
Adjusting harness zip size M.
Zip harness adjustment size L.
A Position the harness shallower.
B position the harness deeper
2 HARNESS SIZE ADJUSTMENT

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
6
La selletta viene fissata al telaio su tre punti di ancoraggio:
in alto con due bulloni a farfalla, di lato con due distanziali, in basso con due cinghie regolabili.
1) Upper hooks harness with two
Butterfly bolts
Attach the harness to the chassis with the plate
and tighten the two bolts with the butterflies.
ATTENTION
Mount the plate as is indicated on the sticker of
your paramotor
Asymmetric distance bar for:
Rider Thrust.
Anticlockwise rotation of the propeller
Asymmetric distance bar for:
Rider Jet, Rider Race C,
Clockwise rotation of the propeller
3 FITTING THE HARNESS HIGH ATTACK

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
7
2) Assembly of the distance bars
Insert the distance bar
into the square slot
located on the Central frame and close the
Velcro straps.
3) Lateral belt attachment
Fasten the webbing at maximum length
4) Fastening shoulder webbing
Attach the webbing to the right and left of the
frame

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
8
The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways
with two distance bar and bottom with three belts.
1) Upper hooks harness with two Butterfly
bolts
Attach the harness to the chassis with the plate and
tighten the two bolts with the butterflies.
ATTENTION
Mount the plate as is indicated on the sticker of your
paramotor
2) Fixing the frame distance bars
Mount distance bars according to two
regulations:
Regulation 1: 1A = Pilots over 85 kg.
1B = Pilots less 85 kg.
Regulation 2:
Direction 2A (forward) Heavy Pilots
Direction 2B (back) Light Pilots
3) Bottom bracket of the frame with three straps
4 ASSEMBLY OF (LOW ACTIVE HANG POINT)

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
9
Configuration for:
Rider Sprint, Rider Race C, Rider Jet.
Clockwise rotation of the propeller
Configuration for:
Rider Thrust.
Anticlockwise rotation of the propeller

ASSEMBLY MANUAL __ REL . 1.1
___________________________________________________________________________
© Copyright by FLY PRODUCTS s.r.l. Pag.
10
The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways
with two distance bar and bottom with three belts.
1) Upper hooks harness with two
Butterfly bolts
Attach the harness to the chassis with the plate and
tighten the two bolts with the butterflies.
ATTENTION
Mount the plate as is indicated on the sticker of
your paramotor
2) Assembly of the spacer bars
Insert the distance bar into the square slot located
on the Central frame and secure them with bolts
and butterflies
Assemble the distance bar in one of two holes
according to the pilot weight.
5 ASSEMBLY OF: (FIXED HANG POINT)