Frico PA3210CA User manual

PA3200C
.... 16
SE .... 23 GB
Original instructions
.... 29
NO .... 36 DE .... 44 ES
.... 52
FR .... 60 IT .... 68 NL .... 77 PL .... 84 RU
.... 92
FI .... 99 DK

PA3200C
2
Introduktionssidorna består huvudsakligen av bilder. För översättning av de
engelska texter som används, se respektive språksidor.
SE
The introduction pages consist mainly of pictures. For translation of the
English texts used, see the respective language pages.
GB
Introduksjonssidene består hovedsakelig av bilder. For oversettelse av de
engelske tekstene, se de respektive språksidene
NO
Les pages de présentation contiennent principalement des images. Pour la
traduction des textes en anglais, consultez la page correspondante à la langue
souhaitée.
FR
Die Einleitungsseiten bestehen hauptsächlich aus Bildern. Für die Übersetzung
der verwendetenTexte in englischer Sprache, siehe die entsprechenden
Sprachseiten.
DE
Las páginas introductorias contienen básicamente imágenes. Consulte la
traducción de los textos en inglés que las acompañan en las páginas del
idioma correspondiente.
ES
De inleidende pagina's bevatten hoofdzakelijk afbeeldingen. Voor een vertaling
van de gebruikte Engelse teksten, zie de pagina's van de resp. taal.
NL
Le pagine introduttive contengono prevalentemente immagini. Per le
traduzioni dei testi scritti in inglese, vedere le pagine nelle diverse lingue.
IT
Początkowe strony zawierają głównie rysunki. Tłumaczenie wykorzystanych
tekstów angielskich znajduje się na odpowiednich stronach językowych.
PL
RU Страницы в начале Инструкции состоят в основном из рисунков, схем и
таблиц. Перевод встречающегося там текста приведен в разделе RU.
Esittelysivut koostuvat lähinnä kuvista. Suvuilla olevien enlanninkielisten
sanojen käännökset löytyvät ko. kielisivuilta.
FI
Introduktionssiderne består hovedsageligt af billeder. For oversættelse af de
engelske tekster, se siderne for de respektive sprog.
DK

PA3200C
3
L = 2 m
A / W
E
DN20 (3/4")
outside thread
1045 / 1555 / 2045
1068 / 1578 / 2068
42256
10 458
167
min 500
99
20950
52
DN20 (3/4 ")
167min 500 min 500
165
20950
min 500 min 500 167165
119
DN20 (3/4 ")
1045 / 1555 / 2045
1068 / 1578 / 2068
42256
10 458
167
min 500
99
20950
52
DN20 (3/4
")
167min 500 min 500
165
20950
min 500 min 500 167165
119
DN20 (3/4 ")
1045 / 1555 / 2045
1068 / 1578 / 2068
42256
10 458
167
min 500
99
20950
52
DN20 (3/4 ")
167min 500 min 500
165
20950
min 500 min 500 167165
119
DN20 (3/4 ")

PA3200C
4
Fig. 2
Fig. 3: Open the unit.
A B
C
Gland
Knock-out
Knock-out
Knock-out
ø17, 5ø17,5
ø32,5
ø25,5
ø20,5
ø17, 5
Gland Gland

PA3200C
5
Fig. 4
Fig. 5
Minimum distance
30 mm 60 mm
min 60

PA3200C
6
min 500 mm
Fig. 6: Mounting with wall brackets
Mounting with wall brackets
PA3210C 2 pcs
PA3215C 2 pcs
PA3220C 3 pcs
A
BC
D
Ø8 (3x)
Ø7
Ø16
213
37
260
75 35 20

PA3200C
7
Accessories
PA34TR15 PA3210C, PA3215C, 1 m
PA34TR20 PA3220C, 1 m
PA2P15 PA3210C, PA3215C, 1 m
PA2P20 PA3220C, 1 m
PA3PF15 PA3210C, PA3215C
PA3PF20 PA3220C
PAMLK PA3200C
PA3EF10 PA3210C W
PA3EF15 PA3215C W
PA3EF20 PA3220C W
FHDN20 PA3200C W
PA2DR
PA34TR PA2P PA3PF
PA2DR
PAMLK FHDN20
AUTO
PA3EF
VKF
SD230 BPV10
VLSP
VOT
VLSP15LF DN15
VLSP15NF DN15
VLSP20 DN20
VLSP25 DN25
VLSP32 DN32
VOT15 DN15
VOT20 DN20
VOT25 DN25

PA3200C
8
PA3210CA / PA3215CA / PA3220CA
5A x 3
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
IR
PA3210CA PA3215CA PA3220CA
C°
3220CA 3215CA 3210CA Red
Red
Black
Blue
Brown
LN Low
Mid b1 c1
Orange
Yellow Yellow Yellow
Mid Low
Blue
Black
b1 c1
Orange
Red
Orange
White White White
C°
Black
Blue
Brown
M
Left motor
~
Run
Only 2 m version
Black
Blue
Low
LN Mid c1b1
M
Right motor
~
Run

PA3200C
9
PA3210CE8 / PA3215CE12 / PA3220CE16
5A x 3
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
K2
Over heat cut-out
°C
K1K1 = high power
K2 = low power
L2 PE
L1 LN
L3
400V 3N~
Over heat
°C
cut-out
PA3210CE PA3215CE PA3220CE
Only 2 m version
K4
K3K3 = high power
K4 = low power
PE
400V3~
L2 L1
L3
C°
Black
Brown
Blue
Mid Low
N L c1
b1
Red
Yellow
Orange
White
Blue
Black
C°
M
Left motor
~
Run
M
Right motor
~
Run
Black
Blue
Brown
Nb1 c1
Mid
LLow
Red
Yellow
Orange
Black
Blue
White

PA3200C
10
PA3210CE08YD / PA3215CE12YD / PA3220CE16YD 230V3~
L2 PE
L1 LN
L3
(230V 3~)
PA3210CEYD PA3215CEYD PA3220CEYD
L2 PE
L1
L3
(230V 3~)
5A x 3
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V DOOR
AFTER
WATER
INTERNAL SENSOR
IR
Over heat
cut-out
°C
Over heat
cut-out
°C
Brown
C°
Blue
Black
Mid
NL Low b1 c1
Orange
White
Black
Blue
Red
Yellow
C°
Orange
White
Black
Blue
Yellow
Red
b1
NL Low
Mid c1
Brown
Blue
Black
M
Left motor
~M
Right motor
~
Run Run

PA3200C
11
PA3210CE08YD / PA3215CE12YD / PA3220CE16YD 400V3~
L2 PE
L1 LN
L3
400V 3N~
PA3210CEYD PA3215CEYD PA3220CEYD
L2 PE
L1
L3
400V3~
5A x 3
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V DOOR
AFTER
WATER
INTERNAL SENSOR
IR
Over heat
cut-out
°C
Over heat
cut-out
°C
Brown
Black
C°
Blue
Low
NMid
Lb1 c1
Red
Blue
Black
Orange
White
Yellow
Brown
C°
Blue
Black
M
Left motor
~M
Right motor
~
Run Run
Black
Blue
Orange
White
Red
Yellow
NLow
LMid b1 c1

PA3200C
12
PA3210CW / PA3215CW / PA3220CW
5A x 3
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
PA3210CW PA3215CW PA3220CW
Black
Brown Blue
C°
3220CW 3215CW 3210CW
Red
Black
Blue
Brown
LN Low
Mid b1 c1
Orange Orange
White
Yellow
White
Mid Low
Blue
Black
b1 c1
Red
Orange
Red
Yellow
White
Yellow
C°
Black
Blue
Brown
M
Left motor
~
Run
Only 2 m version
Black
Blue
Low
LN Mid c1b1
M
Right motor
~
Run

PA3200C
13
PAMLK
On
Off
M
C°
~
NF1F2F3
OUT PAMLK
CNC NO
Motor alarm (pot. free contact)
5A x 3
5A
16A
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
C°
C°
Black
Brown
Blue
Mid Low
N L c1
b1
C°
M
Left motor
~
Run
M
Right motor
~
Run
Black
Blue
Brown
Nb1 c1
Mid
LLow
Only 2 m version

PA3200C
14
Type Output
[kW]
Airflow*1
[m3/h]
Sound
power*2
[dB(A)]
Sound
pressure*3
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Length
[mm]
Weight
[kg]
PA3210CA 0 1100/1750 73 46/57 230V~ 0,7 1068 22
PA3215CA 0 1700/2750 74 46/59 230V~ 1,0 1578 32
PA3220CA 0 2300/3500 75 50/60 230V~ 1,3 2068 42
Type Output
steps
[kW]
Airflow*1
[m3/h]
∆t*4
[°C]
Sound
power*2
[dB(A)]
Sound
pressure*3
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Voltage [V]
Amperage [A]
(heat)
Length
[mm]
Weight
[kg]
PA3210CE08 5/8 1100/1750 22/13 72 46/57 230V~ 0,65 400V3~/11,5 1068 26
PA3215CE12 8/12 1700/2750 21/13 75 46/59 230V~ 1,0 400V3~/17,3 1578 37
PA3220CE16 10/16 2300/3500 22/13 76 50/60 230V~ 1,3 400V3~/23,1 2068 51
Type Output
step
[kW]
Airflow*1
[m3/h]
∆t*4
[°C]
Sound
power*2
[dB(A)]
Sound
pressure*3
[dB(A)]
Voltage
motor
[V]
Amp.
motor
[A]
Voltage
heat
[V]
Amp.
heat
[A]
Length
[mm]
Weight
[kg]
PA3210CE08YD 5/8 1100/1750 22/13 72 46/57 230V~ 0,65 230V3~/400V3~ 20,1/11,5 1068 26
PA3215CE12YD 8/12 1700/2750 21/13 75 46/59 230V~ 1,0 230V3~/400V3~ 30,1/17,3 1578 37
PA3220CE16YD 10/16 2300/3500 22/13 76 50/60 230V~ 1,3 230V3~/400V3~ 40,2/23,1 2068 51
Type Output*5
[kW]
Airflow*1
[m3/h]
∆t*4,5
[°C]
Water
volume
[l]
Sound
power*2
[dB(A)]
Sound
pressure*3
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Length
[mm]
Weight
[kg]
PA3210CW 8 1050/1700 16/14 1,3 70 45/55 230V~ 0,65 1068 26
PA3215CW 14 1850/2700 17/15 2,1 73 46/57 230V~ 0,7 1578 36
PA3220CW 18 2200/3300 18/16 2,7 74 49/58 230V~ 1,3 2068 48
2Water heat - PA3200C W (IP21)
3Electrical heat - PA3200C E (IP20)
1Ambient, no heat - PA3200C A (IP21)
*1) Lowest/highest airflow of totally 3 fan steps.
*2) Sound power (LWA) measurements according to ISO 27327-2: 2014, Installation type E.
*3) Sound pressure (LpA). Conditions: Distance to the unit 5 metres. Directional factor: 2. Equivalent
absorption area: 200 m². At lowest/highest airflow.
*4) ∆t = temperature rise of passing air at maximum heat output and lowest/highest airflow.
*5) Applicable at water temperature 60/40 °C, air temperature, in +18 °C.
Protection class for units with electrical heating: IP20.
Protection class for units without heating and units with water heating: IP21.
CE compliant.
3Electrical heat 230V3~ - PA3200C E (IP20)

PA3200C
15
Output charts water PA3200C
*1) Recommended outlet air temperature for good comfort and optimized output.
*2) Nominal output at given supply and return water temperature.
Supply water temperature:80 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 80/60 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PA3210CW max 1700 9,8 42 0,06 1,4 14,6 43 0,18 8,5
min 1050 6,2 38 0,04 0,5 10,6 48 0,13 4,8
PA3215CW max 2700 15,6 38 0,09 2,0 24,7 45 0,30 16,8
min 1850 10,5 34 0,06 0,9 19,2 49 0,23 10,6
PA3220CW max 3300 18,6 36 0,10 1,9 31,2 46 0,38 19,0
min 2200 12,6 34 0,07 0,9 23,7 50 0,29 11,5
Supply water temperature: 60 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 60/40 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PA3210CW max 1700 10,0 48 0,19 10,5 8,0 32 0,10 3,1
min 1050 6,1 41 0,08 2,1 5,8 34 0,07 1,8
PA3215CW max 2700 16,0 45 0,26 13,4 13,9 33 0,17 6,3
min 1850 10,8 40 0,13 4,0 10,8 35 0,13 4,0
PA3220CW max 3300 18,9 42 0,26 10,2 1 7, 6 34 0,21 7, 1
min 2200 12,9 39 0,15 3,6 13,4 36 0,16 4,4
Supply water temperature: 55°C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 55/35°C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PA3210CW max 1700 9,8 48 0,35 31,3 6,3 29 0,08 2,1
min 1050 5,9 42 0,11 3,6 4,6 31 0,06 1,2
PA3215CW max 2700 15,7 46 0,42 32,9 11,2 30 0,14 4,3
min 1850 10,8 42 0,19 8,1 8,7 32 0,11 2,8
PA3220CW max 3300 18,7 44 0,40 22,4 14,1 31 0,17 4,9
min 2200 12,5 39 0,19 5,9 10,7 32 0,13 3,0
Supply water temperature:70 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 70/50 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PA3210CW max 1700 9,7 44 0,09 2,7 11,3 38 0,14 5,5
min 1050 6,1 39 0,05 0,9 8,3 41 0,10 3,2
PA3215CW max 2700 15,6 41 0,13 3,9 19,4 39 0,24 11,1
min 1850 11,0 38 0,08 1,7 15,0 42 0,18 7, 0
PA3220CW max 3300 18,9 39 0,15 3,7 24,4 40 0,30 12,5
min 2200 12,9 36 0,09 1,6 18,6 43 0,23 7, 6

PA3200C
23
EN
General Instructions
Read these instructions carefully prior to
installation and use. Keep this manual for
future reference.
The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid should the product
be used in the manner intended and in
accordance with the instructions.
Application
PA3200C is a compact air curtain with a
recommended installation height of 3,2
metres. The air curtain has an integrated
control system and can be remotely
controlled.
The air curtain is available without heat,
with electrical heating and with water heating.
Protection class for units with electrical
heating: IP20.
Protection class for units without heating and
units with water heating: IP21.
Operation
Air is drawn in at the top of the unit and
blown downwards shielding the door opening
and minimizing heat loss. To achieve the
optimum curtain effect the unit must extend
the full width of the door opening.
The grille for directing the outlet air is
adjustable and is normally angled outwards to
achieve the best protection against incoming
air.
The efficiency of the air curtain depends on
the air temperature, the pressure differencial
across the doorway and any wind load.
NOTE! Negative pressure in the building
considerably reduces the efficiency of the air
curtain. The ventilation should therefore be
balanced.
Mounting
The air curtain is installed horizontally with
the outlet air grille facing downwards as close
to the door as possible. The product must be
mounted in such a way to allow future service
and maintenance. Minimum distance from
outlet to floor for electrically heated units is
1800 mm. For other minimum distances, see
fig. 4.
Brackets and torx bit are enclosed in the
gable end packaging upon delivery.
Mounting with wall brackets (fig. 6)
1.Mount the brackets on the wall, see fig.6A
and dimension drawing fig.1. If the wall is
uneven the brackets must be compensated
for this.
2.Hook on the unit at the lower edge of the
brackets. (Fig.6B)
3.Bend the top of the console over the the
unit and slide the units screws along the
rail into the slots on the consoles. (Fig.6C)
When the bracket is bent once, it must be
replaced if bent back more than 45 °.
4.Lock the nuts against the brackets. (Fig.6D)
Horizontal mounting on the ceiling
Threaded rods, hanging brackets and ceiling
mounting brackets for ceiling mounting are
available as accessories, see accessories pages
and separate manuals.
Electrical installation
The installation, which should be preceded by
an isolator switch with a contact separation
of at least 3 mm, should only be wired by a
competent electrician and in accordance with
the latest edition of IEE wiring regulations.
The control system is pre-installed in the air
curtain.
Unit without heating
Connected via the built-in control board with
1,5 m cord and plug.
Unit with water heating
Connected via the built-in control board with
1,5 m cord and plug.
Installation and operating instructions

PA3200C
24
EN
Service, repairs and maintenance
For all service, repair and maintenance first
carry out the following:
1.Disconnect the power supply.
2.The front hatch is removed by removing
the screws on the top of the unit and then
detach the bent edge at the bottom. (Fig.3)
3.After the service, repair and maintenance
reattach the front hatch. Place the hatch
at the lower edge with the bent edge and
fasten on top with screws.
Note that when carrying out work where the
end is removed, the outlet grille also detaches.
Start-up (E)
When the unit is used for the first time or
after a long period of non-use, smoke or an
odour may result from dust or dirt which has
collected on the element. This is completely
normal and disappears after a short time.
Adjustment of the air curtain and airflow
The direction and speed of the airflow should
be adjusted considering the load on the
opening. Pressure forces affect the airstream
and force it inwards towards the premises
(when the premises are heated and the
outdoor air is cold).
The airstream should, therefore, be directed
outwards to withstand the load. Generally
speaking, the higher the load, the greater the
angle required.
Basic setting fan speed
The fan speed when the door is open is
set using the control. Note that the airflow
direction and the fan speed may need fine
adjustment depending on the loading of the
door.
Filter (W)
The water coil is protected against dirt and
blockage by an internal air filter which covers
the coil face. In environments where the filter
requires frequent cleaning, it is advisable to
use an external intake filter (see accessories
pages), which provides easier maintenance,
since the unit does not need to be opened.
When an external filter is used, the internal
filter is removed.
[kW] [V] [mm2]
0 230V~ 1,5
PA3210CE08 8 400V3~ 2,5
PA3215CE12 12 400V3~ 4
PA3220CE16 16 400V3~ 6
*) Dimensioning of external wiring shall comply
with applicable regulations and local deviations
may occur.
Type Output Voltage Minimum
area*
Control
Connecting the water coil (W)
The installation must be carried out by an
authorised installer.
The water coil has copper tubes with
aluminium fins and is suitable for connection
to a closed water heating system. The heating
coil must not be connected to a mains
pressure water system or an open water
system.
Note that the unit shall be preceded by a
regulating valve, see Frico valve kit.
The water coil is connected on top of the unit
via steel pipes with DN20 (3/4’’) terminals,
external thread. Flexible hoses are available
as accessories, see accessories pages.
The connections to the heating coil must
be equipped with shut off valves to allow
trouble-free removal. The water coil is
equipped with a drain valve. A vent valve
Unit with electrical heating
The electrical connection is made on the top
of the unit. See Fig.2. Control (230V~) and
power supply for heat (400V3~) should be
connected to a terminal block in the terminal
box. 2-metre and longer units require dual
power supplies.
The largest cable diameter for the terminal
block is 16 mm². The cable glands used must
meet the protection class requirements. In
the distribution board, it is to be indicated
that ”the air curtains can be supplied from
more than one connection”.
See wiring diagrams.
should be connected at a high point in the
pipe system. Air valves are not included.
NOTE: Care must be taken when
connecting the pipes. Use a pipe wrench or a
similar tool to grip the air curtain connections
to prevent straining of the pipes and
subsequent water leakage during connection
to the water supply pipe-work.

PA3200C
25
EN
Overheating
The air curtain unit with electrical heating is
equipped with an overheat protection. If it is
deployed due to overheating, reset as follows:
1.Disconnect the power supply with the
isolator switch.
2.Determine the cause of overheating and
rectify the fault.
3.Remove the front hatch.
4.Press the red button located inside the
air curtain unit, at the inner gable of the
terminal box.
5.Reattach the front hatch and connect the
unit again.
All motors are equipped with an integral
thermal safety cut-out. This will operate,
stopping the air curtain should the motor
temperature rise too high. The cut-out
will automatically reset when the motor
temperature has returned to within the
motor’s operating limits.
Replacing heating elements/heating
package (E)
1.Mark and disconnect the cables to the
heating elements/package.
2.Remove the mounting screws securing the
heating elements/package in the unit and
lift the heating elements/package out.
3.Install the new heating elements/package in
reverse order to the above.
Draining the water coil (W)
The drain valve is on the underside of the coil
on the connector side. It can be accessed via
the front hatch.
Replacing the water coil (W)
1.Shut off the water supply to the unit.
2.Disconnect the connections to the water
coil.
3.Detach the plastic ends.
4.Detach the intake grille by drilling out the
rivet(s).
5.Remove the mounting screws securing the
coil in the unit and lift out.
6.Install the new coil in reverse order to the
above.
Replacing motor or impeller
1.Remove the front.
2.Remove gable end.
3.Remove the screw between motor and fan.
4.Disconnect the cables to the motor.
5.Remove the screws securing the motor and
lift it out together with the impeller.
6.Install the new motor and/or the new
impeller as above in reverse order.
Temperature control
See control pages.
Maintenance
Unit with water heating
The appliance filter should be cleaned
regularly to ensure the air curtain effect and
heat emission from the device. How often
depends on local circumstances. A clogged
filter is not a risk, but the appliance function
can fail.
1.Disconnect the power supply.
2.The front hatch is removed by removing
the screws on the top of the unit and then
detach the bent edge at the bottom. (Fig.3)
3.Remove the filter and vacuum clean or
wash it. If the filter is clogged or damaged, it
may need to be changed.
All units
Since fan motors and other components are
maintenance-free, no maintenance other than
cleaning is necessary. The level of cleaning
can vary depending on local conditions.
Undertake cleaning at least twice a year. Inlet
and exhaust grilles, impeller and elements
can be vacuum cleaned or wiped using a
damp cloth. Use a brush when vacuuming
to prevent damaging sensitive parts. Avoid
the use of strong alkaline or acidic cleaning
agents.

PA3200C
26
EN
Troubleshooting
If the fans are not running or do not perform pro-
perly, check the following:
• The functions and settings of the built-in
control system.
• That the intake grille/filter is not dirty.
If there is no heat, check the following:
• The functions, internal sensor and settings
of the built-in control system.
For units with electrical heating, also check the fol-
lowing:
• Power supply to electric heater coil; check
fuses and circuit-breaker (if any).
• That the overheat protection has not been
deployed.
For units with a water coil, also check the following:
• That the water coil is air free.
• That there is sufficient water flow and
pressure.
• That incoming water is heated adequately.
If the fault cannot be rectified, please contact
a qualified service technician.
Residual current circuit breaker (E)
When the installation is protected by means
of a residual current circuit breaker, which
trips when the appliance is connected,
this may be due to moisture in the heating
element. When an appliance containing a
heater element has not been used for a long
period or stored in a damp environment,
moisture can enter the element.
This should not be seen as a fault, but is
simply rectified by connecting the appliance
to the main supply via a socket without a
safety cut-out so that the moisture can be
eliminated from the element. The drying
time can vary from a few hours to a few days.
As a preventive measure, the unit should
occasionally be run for a short time when it is
not being used for extended periods of time.
Packaging
Packaging materials are chosen with
consideration to the environment and are
therefore recyclable.
Handling of product at end of working life
This product may contain substances
necessary for the functionality of the
product but potentially dangerous for the
environment. The product should not be
disposed of mixed with general household
waste but delivered to a designated collection
point for environmental recycling. Please
contact the local authority for further details
of your nearest designated collection point.
Safety
• For all installations of electrically heated
products a residual current circuit breaker
300 mA for fire protection should be used.
• Keep the areas around the air intake
and exhaust grilles free from possible
obstructions!
• The unit must not be fully or partially
covered as overheating can result in a fire
risk!
• Lifting equipment must be used to lift the
unit.
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made
by children without supervision.
• Children of less than 3 years should be
kept away unless continuously supervised.
• Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or
installed in its intended normal operating
position and they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
• Children aged from 3 years and less
than 8 years shall not plug in, regulate
and clean the appliance or perform user
maintenance.
CAUTION — Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.

PA3200C
27
EN
1234
ON
1234
ON
230V~
Control
The air curtain has an integrated control
system and can be remotely controlled.
ON OFF
Actuator SD230
(remove the quick
connector)
Black
Brown
Blue
External on/off
Eg time switch.
External potential free closure
= off
PA2DR
(accessory)
Factory setting dip-switches - Unit with water
heating
Dip-switch 3 is used for PA2DR (optional).
21
3
Factory setting dip-switches - Unit without heating
or with electrical heating
Dip-switch 3 is used for PA2DR (optional).