Frico Thermocassette HP3 User manual

Thermocassette HP
.... 6 ... 14.... 10 .... 12
.... 8
GB FRNO DESE
... 16
FI ... 18 RU

Thermocassette HP
2
HP6
HP3
Min.distance
[mm]
Ceiling (A) 80
Wall, long side of the unit (B) 50
Wall, short side of the unit (B) 50
Flammable material (C) 500
Floor (D) 1800
Fig. 1: Minimum mounting distance
Minimum mounting distance
1,8
1,8

Thermocassette HP
3
Mounting
Fig. 2
A
B
C
D
E
Fig. 1

Thermocassette HP
4
Technical specifications | Thermocassette HP.
Type E-nr [SE] EL-nr [NO] Output (1)
[W]
Voltage (2)
[V]
Amperage (3)
[A]
Max. surface
temperature (4)
[°C]
Weight (5)
[kg]
HP3 85 700 21 300 230V~ 1,3 100 5,8
HP6 85 700 34 600 230V~ 2,6 100 10,7
Protection class: (IP55), jet-proof design.
CE compliant.
Complies with the requirements for flammable areas according to SEMKO 111FF.
(1)
SE: Effekt
GB: Output
NO: Effekt
FR: Puissance
DE: Heizleistung
RU: Мощность
FI: Lämmitysteho
(2)
SE: Spänning
GB: Voltage
NO: Spenning
FR: Tension
DE: Spannung
RU: Напряжение
FI: Jännite
(3)
SE: Ström
GB: Amperage
NO: Strøm
FR: Intensité
DE: Stromstärke
RU: Ток
FI: Virta
(4)
SE: Maximal yttemperatur
GB: Max. surface temperature
NO: Maksimal overflatetemp.
FR: Température de surface
DE: Max. Oberflächentemperatur
RU: Max. температура поверхности
FI: Suurin pintalämpötila
Accessories
ERP KRT1900T10S
(5)
SE: Vikt
GB: Weight
NO: Vekt
FR: Poids
DE: Gewicht
RU: Вес
FI: Paino
Type E-nr [SE] EL-nr [NO] HxWxD
[mm]
ERP 85 820 05 54 328 86 153x94x43
ERPS 85 820 10 54 328 90 153x94x43
T10S 85 809 33 54 911 12 80x80x31
TKS16 85 809 37 54 911 51 80x80x39
TD10 85 809 39 54 911 39 80x80x31
KRT1900 85 810 12 54 910 50 165x57x60
74701 85 744 90 54 323 30
20
25
30
15
10
5
TKS16 TD10 74701

Thermocassette HP
5
Wiring diagrams HP
LN
HP
K12U34U K GG
LN
230V~
ERP
HP LN
HP
LN
HP
LN
HP LN
HP
P
230V~
N
Thermostat
Control by thermostat
Output control
Internal wiring diagram
LN
HP
230V~

Thermocassette HP
8
GB
General Instructions
Read these instructions carefully before
installation and use. Keep this manual for
future reference.
The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid if the product is used
in the manner intended and in accordance
with the instructions.
Area of use
The heating panel is intended for the heating
of rooms requiring free walls. The panel
can be used for complete heating, or as an
additional heater (e.g. over a reception desk
or other work place).
There are two ratings: 300 W and 600 W.
The heating panel provides mainly radiation
heating. This implies that to obtain the
same experienced temperature it is possible
to reduce the air temperature in the room,
which saves energy.
Because of the low surface temperature,
max 100°C, the heating panel is suitable
for rooms with relatively low ceiling height.
Thanks to the location, the panel is protected
from any physical contact or damage. There
is no risk of being burned.
Design
One or more units have to be connected to
power line with a differential circuit breaker
rated at 30 mA. The cable section has to be at
least 1,5 mm2.
If the units are to be extra insulated, then
this insulation must not exceed a value of
R=5 m2K/W.
Mounting
Integrated in ceiling (put in exposed grid)
See fig. 1
1. Lateral distance to wall shall be at least
50 mm.
2. The heater(s) should only be wired by a
competent electrician, and in accordance
with existing national regulations.
3. Place the cassette in the required ceiling
square. Minimum design height ”H” for
dismounting, T-profile 32x15: 150 mm,
T-profile 38x24: 200 mm. NOTE! Avoid
fixing vertical bars in the T-profile where a
heating panel is to be installed. The panel
fills out the whole square.
4. Connect the panel.
5. The second last page in this mounting
instruction is to be filled out and fixed
adjacent to the distribution board and it
has to contain (drawing) the locations of
the heating units.
Bracket mounting
See fig. 2
1. Mounting height above floor shall be at
least 1,8 m, and lateral distance to wall at
least 50 mm. When mounting in gypsum
board, make sure that the mounting
brackets are anchored in the beam behind.
During long-term high temperatures the
strength of the board is reduced.
2. The heater(s) should only be wired by a
competent electrician, and in accordance
with existing national regulations.
3. Measure, drill and screw the two loose
brackets to the ceiling. Do not tighten the
screws yet. It is important that the holes
come at right angles, cross measure. (fig.
2A)
4. Hook the panel brackets to the ones on the
ceiling (only the side nearest to the cable
gland). Allow panel to hang vertical. (fig.
2B)
5. Connect the panel.
6. Swing up the panel, and adjust the lateral
position of the ceiling mounted brackets.
(fig. 2C)
7. Swing down the panel and tighten the
screws in the ceiling. (fig. 2D)
8. Swing up the panel again and hook the
panel bracket ends in the ceiling brackets.
NOTE! Make sure that the brackets do not
become unhooked at the other end.
9. Secure the panel with a screw (enclosed
on delivery) at each hanging point. (fig.
2E)
10.The second last page in this mounting
instruction is to be filled out and fixed
Mounting and assembly instruction

Thermocassette HP
9
GB
adjacent to the distribution board and it
has to contain (drawing) the locations of
the heating units.
Replacement of cable
1. Because of limitations in the IP55 category
the cable cannot be changed.
2. If the cable is damaged the unit has to be
scrapped.
Safety
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by children without
supervision.

Place this drawing adjacent to the distribution board
OBS!
– do not restrict the thermal emission of the heated ceiling
– do not affix materials other than those recommended
– do not insert nails or screws
HP3, 300W, 220-240V
HP6, 600W, 220-240V
Drawing of the installation

Item no: 204773, 20150327 HH
Main office
Frico AB Tel: [phone]
Box 102
SE-433 22 Partille [email protected]
Sweden www.frico.se
For latest updated information and information
about your local contact: www.frico.se