Front Runner TBMK009 User manual

ENG
Hard Shell Tent
Support Channels
TBMK009_REV_A02 © 2021 FRONT RUNNER VEHICLE OUTFITTERS 1
IMPORTANT WARNING!
Thank you for purchasing Front Runner Hard Shell Tent Support Channels.
Before you start, take a moment to familiarize yourself with this Fitting Instruction and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
TBMK009
READ ME !
FRONT RUNNER CAN NOT RECOMMEND A MAXIMUM LOAD CARRYING CAPACITY. PLEASE REFER TO YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS. IT IS CRITICAL
THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS
TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

TBMK009_REV_A02 © 2021 FRONT RUNNER VEHICLE OUTFITTERS 2
IN THE BOX
FIGURE 1.1
1 2 X Hard Shell Tent Channel Support
2 8 X M8 x 25 Button Head Bolt
3 8 X M8 SS Spring Washer
4 8 X M8 x 16 x 1.6 SS Flat Washer
5 8 X M8 Channel Nut
6 4 X Rubber Strip
IN THE BOX TOOLS NEEDED
IN THE BOX
1
6
1
5
4
3
2
1GET ORGANIZED
5mm

TBMK009_REV_A02 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.2
2.3
2.4
2.1
2.1
2.2
2.3
4MM
2
3
4
5
1
Slide four M8 Channels Nuts (Item 5) into
each of the tent mounting channels.
Apply the Rubber Strip (Item 6) to the Tent
Support Channels so that it sits between the
Channel and the tent.
Loosely fit the Tent Support Channels to the
tent by using M8 x 25 Button Head Bolts,
M8 SS Spring Washers and M8 x 16 x 1.6SS
Flat Washers (Items 2, 3 & 4) as shown.
Fit your tent mounting system (TBMK012)
to the Rack.
Refer to TBMK012 fitment guide for
instructions.
Move the Tent Support Channels (Item 1)
outward as shown to create sufficient
support underneath the tent where needed.
Fully tighten the Tent Support Channels to
the tent.
11

COMPLETION
3
9
3.1
Congratulations. You did it. Take a step back and admire your work!
TBMK009_REV_A02 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
4
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
4
Now's the time to visit your favorite Front Runner Dealer in person or Online.
Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.