FUFU & GAGA Shoe Storage Cabinet User manual

Version:09/20/2022 1/17
Shoe Storage Cabinet

2/17
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
3/17
A x 8 B x 8
15 x10mm
C x 12 D x 2
G x 4
6 x 30 mm
6 x 30 mm
6 x 35 mm
E x 6
F x 1
4 x 40 mm
I x 12 J x 42 H x 3
L x 3
K x 2 N x 6 O x 6
Mx 3
4 x 12 mm
4 x 16 mm
Q x 2
P x 6 R x 2 S x 4
4x12 mm
4 x 35 mm
T x 12
3 x 16 mm

4/17
10 x3
x3 x3
x3
11
10
1
2
9
3
5
5
6
7
7
8
8

11
6 x 35 mm
A x 4
5/17
A
A
P
P
P
P
O
O
O
P
P
O
O
O
A
A
A
O x 6 P x 6
O
P
3
4
Knock part(O,P) into corresponding holes
in No.3 and No.4 plate as shown.
Insert quickfit screw(A) into No.3 and No.4
plate with a screwdriver as shown.

2
6/17
6 x 35 mm
A
A
A
A
A
C
C
B
B
B
B
C
C
R
R
K
K
x 4 B x 4
IIIIII
4
3
5
7
7
1
15x
10 mm
C x 4 K x 2 R x 2
4 x 12 mm6 x 30 mm
R
K
A
B
C
Insert quickfit screw(A) into No.1 plate
with a screwdriver as shown.
Fix part(R) to No.1 plate with screw(K)
as shown.
Slide No.5 plate into available
slots between two No.7 plates
at first.
Connect No.3 and No.4 plate with No.7(x2)
using wooden dowel(C), then turn cam
lock(B) clockwise to tighten as
shown.

3
7/17
S x 4C
C
C
C
C
S
S
S
S
x 4
4 x
35 mm
6 x 30 mm
5
5
2
3
4
7
7
C
S
如图所示 ；2，3，4，板插入C木榫，与 1号板
dowel(C), then fix with screw(S)
Slide another No.5 plate into available slots
in No.3, No.4 and No.7 plates at first.
Cover No.2 plate using wooden
as shown.

4
8/17
如图所示 ；2，3，4，板插入C木榫，与 1号板
4
3
2
5
5
8
8
8
8
F
F
G
G
x 1 G x 4
6
x 30
mm
Fix No.8 leg to No.2 plate using screw(G) as shown.
2
8
8
F
G
G

5
9/17
如图所示 ；2，3，4，板插入C木榫，与 1号板
B
C
Bx 4
15x
10 mm
C x 4
6 x
30 mm
6
2
5
5
7
7
3
4
2
1
6
5
5
IIIIII
Slide another No.6 plate into available
slots in No.3, No.4 and No.7 plates
at first.
Cover No.1 plate to the top using wooden
dowel(C), then turn cam lock(B)
clockwise to tighten as shown.

6
6
5
4
5
10/17
I
I
I
I
I
I
I
T
T
T
T
T
T
T
T
T
T
I
T
T
T
I
I
I
I
I
I
x 12 T x 12
3 x 16 mm
Reinforce back plate using part(I) and screw(T) as shown.

7
11/17
8
D
D
D
R
x 2
4x40 mm
Q x 2
Q
Q
Q
123
Q
D
Install anit-tipping device with
Drill holes on your wall,
and knock part(Q) into.
screw(D) as shown.

9
12/17
H x 3 E x 6
4 x 16 mm
Jx 18
E
H
E
J
J
L
M
M
J
J
J
J
J
J
J
9
x3
4 x 12 mm
M
Lx 3 x 3
E
E
H
Fix plastic part(L,M) to No.9 plate
with screw(J) as shown,
Fix handle(H) with screw(E).

10
13/17
Jx 12
4 x 12 mm
J
J
x3
x3
J
J
J
11
9
10
9
11
J
10
Attach No.11 and No.10 plate to the plastic parts
and fix with screw(J) as shown.

11
14/17
N x 6 J x 6
4x12 mm
J
N
J
J
N
N
J
J
N
N
J
J
N
N
Fix these drawers to side plates of the unit
by fixing plastic part using part(N) and screw(J)
as shown.

12
15/17
J x 6
4x12 mm
10
J
J
J
10
J
J
10
J
J
Fix sides of No.10 plate to plastic part
with screw(J) as shown.