FUFU & GAGA Shoe cabinet User manual

Version:09/13/2022 1/17
Shoe cabinet

2/17
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

3/17
Ax16(+1)
Ø6x35mm
Bx16(+1)
Ø15x10mm
Cx26(+2)
Ø6x30mm Ø4x35mm
Ø6x12mm Ø3.5x12mm
Ø3.5x14mm Ø3x12mm Ø4x12mm
Ø6x14mm
Dx12(+1)
Ex3 Fx8 Gx6 Hx54(+5)
Ix6 Jx16(+1) Kx2 Lx2
Mx4 Ox4
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Nx3
E-1 G-1 G-2 G-3
E-2
Px8
Ø4x16mm

4/17
Qx4 Rx2
Ø5x10mm Ø6x30mm
Sx12(+1)

5/17
x3
15
15
15
14
16
16
17
19
20
1
2
3
4
5
7
6
8
9
10
12
12
13 11
10
18
10
10

6/17
1
2Gx6
A
A
A
A
A
A
6
6
5
6
5
Ax6
Ø6x35mm
Insert quickfit screw(A) into corresponding holes
in plate 5 and 6 as shown.
G-1
G-1
G-1
G-1
G-1
G-1
G-2
G-2
G-2
G-2
G-2
G-2
Use a hammer to knock part(G-1,G-2)
into plate 5 and 6 as shown.
G-1 G-2

7/17
3
4
Attach plate 2, 3 and 4 to plate 5 with
wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
Bx3 Cx3
Ø6x30mmØ15x10mm
5
5
B
B
C
B
C
C
2
2
3
4
Attach plate 6 to plate 2, 3 and 4 with
wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
Bx3 Cx3
Ø6x30mmØ15x10mm
B
C
B
C
BC
5
6
6
2
2
3
4
IIIIII
IIIIII

8/17
5
6Ax10
Ø6x35mm
1
9
C
D6
6
6
8
4
5
C
Dx2
Ø4x35mm
Cx2
Ø6x30mm
Connect plate 6 with plate 8 using
wooden dowel(C)and fix with screw(D)
as shown.
A
A
A
A
A
A
A
A
A
Insert quickfit screw(A) into
corresponding holesin plate 1and 9
as shown.
A
1
IIIIII
8
D
8

9/17
7
8
Bx2
Ø15x10mm
Cx8
Ø6x30mm
6
6
C
B
8
8
85
5
4
7
7
9
9
9
C
IIIIII
Connect plate 9 to plate 8 with
wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
D
D
D
D
D
D
C
C
C
C
CD
C
C
Attach plate 7 to the bottom of the unit with
wooden dowel(C) and fix with screw(D) as
shown.
D
C
4
5
Cx2
Ø6x30mm
Dx8
Ø4x35mm

10/17
9
10
Bx8
Ø15x10mm
Fx8
Ø6x12mm
IIIIII
7
5
6
1
5
6
91
9
9
7
F
F
F
F
F
F
Fix leg 10 to plate 7 with screw(F).
Rotate leg support 18 into
plate 7 as shown.
F
F
18
10
10
10
10
B
B
B
BC
C
C
C
2
C
C
B
C
C
Cover plate 1 to the top with wooden dowel(C)
and turn cam lock(B) clockwise to tighten as shown.
B
B
3
Cx8
Ø6x30mm