Furniture of America CM-AC103 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-18
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM-AC103
Phillips Screwdriver
Flat-Head Screwdriver
(Not Included)
(Not Included)

Page 2 of 7

Parts List
Hardware List
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7

Page 4 of 7
Turn the cam lock
connector with a
screwdriver until it
will not turn any
more with light to
moderate force.
Align the cam lock connector so that the cam lock bolt can
be inserted.
Secure the threaded end of
the cam lock bolt by using a
flat-head screwdriver.
Align the cam lock
bolt with the pre-
drilled hole.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Turn right (clockwise) to tighten
Step 1 Insert a total of 4 wood dowels (#E) and 4 cam lock bolts (#A-1) onto the
legs (#1-1 & #1-2). Insert 4 cam lock connectors (#A-2) onto the right
panel (#3). See diagram below and refer to “CAM LOCK FASTENER
ASSEMBLY INSTRUCTIONS” for connecting those parts together.
#A-1 x 4 pcs
#A-2 x 4 pcs
#E x 4 pcs
Note: Every cam
lock bolt must have
a cam lock
connector in order
to fasten the parts
together.

Step 2 Repeat Step 1 for the assembly of the legs (#1-3 &
#1-4) and the left panel (#2).
Step 3
Page 5 of 7
#A-1 x 4 pcs
#A-2 x 4 pcs
#E x 4 pcs
#A-1 x 5 pcs
#A-2 x 8 pcs
#E x 2 pcs
Insert 3 cam lock bolts (#A-1) onto the leg (#1-4).
Insert 2 wood dowels (#E), 2 cam lock bolts (#A-1)
AND 6 cam lock connectors (#A-2) onto the rear
apron (#4). Insert 2 cam lock connectors (#A-2) onto
the center drawer panel (#5). See diagram below
and refer to “CAM LOCK FASTENER ASSEMBLY
INSTRUCTIONS” for connecting those parts
together.
#

#A-1 x 8 pcs
#E x 2 pcs
Page 6 of 7
Step 5
Step 4 #A-1 x 5 pcs
#A-2 x 10 pcs
#D x 2 pcs
#E x 2 pcs
#2
I. Insert 2 wood dowels (#E) AND 3 cam
lock bolts (#A-1) onto the left panel
(#2).
II. Insert a total of 2 cam lock bolts (#A-1)
onto the legs (#1-3 & #1-4).
III. Insert 4 cam lock connectors (#A-2)
onto the drawer support panel (#6) and
6 cam lock connectors (#A-2) the
bottom shelf (#7).
IV. See diagram and refer to “CAM LOCK
FASTENER ASSEMBLY
INSTRUCTIONS” for connecting those
parts together.
V. Insert 2 screws (#D) through the center
holes of the drawer support panel (#6)
and using a Phillips screwdriver to
secure the drawer support panel (#6)
onto the center drawer panel (#5).
Insert a total of 5 cam lock bolts (#A-1) onto the legs (#1-1 &
#1-2). Insert 2 wood dowels (#E) AND 3 cam lock bolts (#A-
1) onto the left panel (#2). See diagram below and refer to
“CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS” for
connecting those parts together.

Page 7 of 7
Step 7
Step 6
#A-1 x 9 pcs
#A-2 x 9 pcs
#E x 6 pcs
I. Align the drawer cover (#9-1) with the pre-drilled hole in front of the drawer (#9-1).
II. Secure 4 bolts (#F) by using the Allen wrench (#G) to lock the drawer (#9-1) with the
drawer cover (#9-1).
III. Align the knob (#C) with the pre-drilled hole on the drawer cover (#9-1). Insert the
bolt (#B) from the inside of the drawer (#9-1) and secure that bolt using the Allen
wrench (#G) to lock the drawer (#9-1) with the knob (#C).
IV. Repeat the above process to assembly the other drawer (#9-2).
V. Carefully put the table on its upright position. Insert the completed drawers onto the
table. Make sure the table is rested on a flat surface and it does not feel loose or
wobbly. If it does, double check that the connections are secured and properly
tighten.
#B x 2 pcs
#F x 8 pcs
Insert 6 wood dowels (#E) and 9 cam lock bolts (#A-1) onto the top
panel (#8). Insert a total of 9 cam lock connectors (#A-2) onto the
left/right panels, the rear apron and the center drawer panel (#2, #3,
#4 & #5). See diagram below and refer to “CAM LOCK FASTENER
ASSEMBLY INSTRUCTIONS” for connecting those parts together.
Turn right (clockwise) to tighten
#C
#C
ASSEMBLY IS COMPLETED