GE CompactPCI VMIACC-7055 Series User manual

GE
Intelligent Platforms
Publication No: 522-807055-000 Rev. D
Installation Guide
VMIACC-7055*/ACC-7055RC*
CompactPCI®Rear Transition Board for the
VMICPCI-7055*/CPCI-7055RC*
THE ACC-7055RC IS DESIGNED TO MEET THE EUROPEAN UNION (EU) RESTRICTION OF HAZARD-
OUS SUBSTANCE (ROHS) DIRECTIVE (2002/95/EC) CURRENT REVISION.

Document History
Installation Guide Document Number: 522-807055-000 Rev. D
February 22, 2010
Waste Electrical and Electronic Equipment (WEEE) Returns
GE is registered with an approved Producer Compliance Scheme (PCS) and, subject to suitable
contractual arrangements being in place, will ensure WEEE is processed in accordance with
the requirements of the WEEE Directive.
GE will evaluate requests to take back products purchased by our customers before
August 13, 2005 on a case by case basis. A WEEE management fee may apply.

Table of Contents 3
Table of Contents
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 • Handling and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Installation of the Rear Transition Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Installation of the PIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2.1 PIM Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 LED Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.4 Connectors and Headers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.4.1 40-Pin IDE Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.4.2 PIM Site Connector and Pinout (J10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.5 PIM Site Connector and Pinout (J14). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1.5.1 Serial Port Connectors and Pinouts (P9 and P10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
1.5.2 Jumper Configuration for Different Serial Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
1.5.3 CompactFlash Connector and Pinout (P6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1.5.4 CompactFlash Master and Slave (Jumper E4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
1.5.5 Gigabit LAN Port Connectors and Pinouts (J6 and J7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
1.5.6 J3 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
1.5.7 J5 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

List of Figures 4
List of Figures
Figure 1-1 VMIACC-7055/ACC-7055RC Rear Transition Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 1-2 Installation of the VMIACC-7055/ACC-7055RC RTMs with a VMICPCI-7055/CPCI-7055RC SBC . . . . . 8
Figure 1-3 Installing the PIM on the VMIACC-7055/ACC-7055RC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 1-4 LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Figure 1-5 P8 40-pin IDE Header (Internal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Figure 1-6 PIM Site (J10) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Figure 1-7 PIM Site (J14) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Figure 1-8 Serial Port Connectors (P9 and P10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Figure 1-9 Serial Header Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 1-10 CompactFlash Connector (P6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 1-11 CompactFlash Master and Slave Jumper (E4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 1-12 Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 1-13 J3 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 1-14 J5 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

List of Tables 5
List of Tables
Table 1-1 40-pin IDE Header Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Table 1-2 PIM Site (J10) Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Table 1-3 PIM Site (J14) Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 1-4 Serial Port (P9/P10) Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Table 1-5 Jumper Configurations for Different Serial Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Table 1-6 CompactFlash (P6) Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Table 1-7 CompactFlash Master and Slave (Jumper E4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table 1-8 Ethernet Connectors LAN1 and LAN2 Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Table 1-9 J3 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table 1-10 J5 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Handling and Installation 6
1 • Handling and Installation
TheVMIACC‐7055*/ACC‐7055RC*reartransitionmodules(RTMs)aredesigned
tobeusedwiththeVMICPCI‐7055*/CPCI‐7055RC*singleboardcomputers
(SBCs).ThereartransitionmoduleismountedintherearI/Oareaofthechassis
andprovidesassociatedsignalsfromthefrontmountedSBC.Thesignalsare
routedtothebackplanethroughtheJ3andJ5connectors.TheJ4connectorisused
foralignmentonlyandhasnoelectricalconnections.
TheVMIACC‐7055/ACC‐7055RCboardsarefull6Uformfactorboardswitha
CompactFlashconnector,aninternalIDEheader,twoCOMports,twoLANports
(optiondependent),andonePIMsite.

Handling and Installation 7
Figure 1-1 VMIACC-7055/ACC-7055RC Rear Transition Board
LEDs
10/100/1000 Ethernet #2
10/100/1000 Ethernet #1
IDE Connector
VMIACC-7055/
J5
J4
J3
PIM Site
J10
J14
LAN 1
LAN 2
COM 1
COM 2
CompactFlash
IDE/PMC1 I/O
Secondary IDE
RS232 or RS422/485 #1
RS232 or RS422/485 #2
ACC-7055RC

Handling and Installation 8
1.1 Installation of the Rear Transition Module
ThereartransitionmoduleinstallsintherearI/OportionoftheCompactPCI
chassisusingtheJ4connectorasaguide.InstallationoftheVMIACC‐7055/
ACC‐7055RCisshowninFigure1‐2onpage8.
TheGigabitEthernetportsareonlyaccessiblewithcertainoptionsofthe
VMICPCI‐7055/CPCI‐7055RCboards,contactSalesformoredetails.
Figure 1-2 Installation of the VMIACC-7055/ACC-7055RC RTMs with a VMICPCI-7055/CPCI-7055RC SBC
J2
J3
J5
J1
64-bit/100 MHz
PCI-X
PMC Site 2
64-bit/100 MHz
PCI-X
PMC Site 1
Hint HB6
PCI-to-PCI
Bridge
With
PICMG 2.1
Hot Swap
64-bit/100 MHz PCI-X Bus
IBM 750FX/GX
PowerPC
Microprocessor
733 MHz to 1.0 GHz
Marvell
Discovery III
PCI-to-IDE
Bridge
33 MHz
DualATA100
CompactFlash
Socket
512 Kbyte
Flash
64 Mbyte
Flash
RTC
32 Kbyte
NVRAM
10/100/1000 LAN Gbit
PHY
Two Single or One Double Wide PMC Site
PMC Site 1 I/O - 64-bit
Device Bus
64-bit, 66 MHz PCI Bus
RJ45 COM 0
RS232
IPMI
UART
RJ45
w/mag
RGMII
TTL
PCI
PCI
Secondary IDE
RGMII
RGMII Gbit
PHY
Gbit
PHY
Mag
Mag
PICMG 2.16
PICMG 2.16
64-bit
66 MHz
PCI
32-bit
33 MHz
64-bit
CPLD
64-bit, 66 MHz PCI Bus
Dev
Bus
PCI
to
PCI
Bridge
32-bit
33 MHz
EIA-232/422/485 COM1/COM2
Dev
Bus
IPMI Serial
10/100/1000 Ethernet #2
CompactFlash
LAN 2
LAN 1
COM 2 COM 1
LEDs
J3 J4 J5
RS232 or RS422/485 #1
Secondary IDE
IDE Header
RS232 or RS422/485 #2
J10
J14
PIM+ Site
10/100/1000 Ethernet #1
VMICPCI-7055/CPCI-7055RC SBC
Front of Chassis
CompactPCI Chassis
Backplane
Denotes CPCI Chassis
UART
1/4
Xcrv
133 MHz/
200 MHz
JTAG/
COP
SODIMM
(200 MHz
up to 2 Gbyte)
DDR266/
DDR400
UART
1/4
Xcrv
UART
1/2
Xcrv
See Note
NOTE: Zero ohm
resistors for
FABA/B op
IDE/PMC I/O
VMIACC-7055/VMIACC-7055RC
Rear of Chassis
Gigabit Ether Gigabit Ether

Handling and Installation 9
1.2 Installation of the PIM
1.2.1 PIM Site
ThePIMinstallsontheVMIACC‐7055/ACC‐7055RC’sPIMsiteusingtheJ10and
J14connectors.
Figure 1-3 Installing the PIM on the VMIACC-7055/ACC-7055RC
VMIPIM-5797
VMIACC
7055
P8IDE
40-Pin
Header
J5
J4
J3
P9 COM1
P10 COM2
COM2
COM1
J14
J10
P
I
M
J6 LAN 1
P6
CompactFlash
E5
E6
E7
E8
E4
J7 LAN 2

Handling and Installation 10
1.3 LED Definitions
Figure 1-4 LED Definitions
LAN 1 & 2
Yellow LED indicates
the Ethernet isactive.
Green LED indicatesit
haslinked.
ThisLED indicateslink speed.
Yellow LED indicates100Base-TX,
Green LED indicates1000Base-T
and an unlit LED indicates10Base-T.
Ethernet StatusIndicators
All three Pwr LEDsshould
be illuminated (Green) once
power isapplied to the board.
When IDE isactivated, the
IDE ACT LED flashes.
Otherwise LED isunlit.
Power and IDE StatusIndicators
Ethernet
Serial ports
ports
PIM site
Status
Indicators

Handling and Installation 11
1.4 Connectors and Headers
ThereisoneinternalIDE40‐pinheader,onePIMsiteconsistingoftwo64‐pin
connectors,twoCOMports,oneCompactFlashconnectorandtwoGigabit
EthernetportsavailableontheVMIACC‐7055/ACC‐7055RC.TheJ3,J4andJ5
connectorsarestandardCompactPCIbackplaneconnectors.JumpersE5,E6,E7
andE8areusedtosetthemodefortheCOMports.JumperE4isusedto
configuretheCompactFlashformasterorslavemode.
1.4.1 40-Pin IDE Header
WhenanIDEdriveisconnectedtoP8andaCompactFlashisloadedontheP6
connector,oneofthemmustbesetasaslave.See“CompactFlashMasterand
Slave(JumperE4)”onpage16forinstructionsonhowtosettheCompactFlashas
amaster/slave.
NOTE
An 80-conductor cable is required for IDE interfaces above Ultra ATA/66.
Figure 1-5 P8 40-pin IDE Header (Internal)
Table 1-1 40-pin IDE Header Pinout
Pin Signal Pin Signal
1 IDES_RESET# 2 GND
3 IDES_ D[7] 4 IDES_D[8]
5 IDES_ D[6] 6 IDES_D[9]
7 IDES_D[5] 8 IDES_D[10]
9 IDES_D[4] 10 IDES_D[11]
11 IDES_D[3] 12 IDES_D[12]
13 IDES_D[2] 14 IDES_D[13]
15 IDES_D[1] 16 IDES_D[14]
17 IDES_D[0] 18 IDES_D[15]
19 GND 20 Key
21 IDES_DMARQ 22 GND
23 IDES_DIOW# 24 GND
25 IDES_DIOR# 26 GND
27 IDES_IORDY 28 GND
29 IDES_DMACK# 30 GND
31 IDES_INTRQ 32 5V
33 IDES_DA1 34 IDES_CBLIO#
35 IDES_DA0 36 IDES_DA2
37 IDES_CS1# 38 IDES_CS3#
39 HD_ACTA# 40 GND
Pin 2 Pin 40
Pin 1 Pin 39

Handling and Installation 12
1.4.2 PIM Site Connector and Pinout (J10)
Figure 1-6 PIM Site (J10) Connector
Table 1-2 PIM Site (J10) Connector Pinout
PIM Connector (J10) PIM Connector (J10)
Left Side Right Side Left Side Right Side
Pin Name Pin Name Pin Name Pin Name
1 N/C 2 N/C 33 N/C 34 GND
3 N/C 4 N/C 35 N/C 36 N/C
55.0VDC6 N/C 375.0VDC 38 N/C
7 N/C 8 N/C 39 N/C 40 N/C
9 N/C 10 3.3VDC 41 N/C 42 3.3VDC
11 N/C 12 N/C 43 N/C 44 N/C
13 GND 14 N/C 45 GND 46 N/C
15 N/C 16 N/C 47 N/C 48 N/C
17 N/C 18 GND 49 N/C 50 GND
19 N/C 20 N/C 51 N/C 52 N/C
21 5.0VDC 22 N/C 53 5.0VDC 54 N/C
23 N/C 24 N/C 55 N/C 56 N/C
25 N/C 26 3.3VDC 57 N/C 58 3.3VDC
27 N/C 28 N/C 59 N/C 60 N/C
29 GND 30 N/C 61 N/C 62 N/C
31 N/C 32 N/C 63 N/C 64 N/C

Handling and Installation 13
1.5 PIM Site Connector and Pinout (J14)
Figure 1-7 PIM Site (J14) Connector
Table 1-3 PIM Site (J14) Connector Pinout
PIM Connector (J14) PIM Connector (J14)
Left Side Right Side Left Side Right Side
Pin Name Pin Name Pin Name Pin Name
1 PMC1_IO[1] 2 PMC1_IO[2] 33 PMC1_IO[33] 34 PMC1_IO[34]
3 PMC1_IO[3] 4 PMC1_IO[4] 35 PMC1_IO[35] 36 PMC1_IO[36]
5 PMC1_IO[5] 6 PMC1_IO[6] 37 PMC1_IO[37] 38 PMC1_IO[38]
7 PMC1_IO[7] 8 PMC1_IO[8] 39 PMC1_IO[39] 40 PMC1_IO[40]
9 PMC1_IO[9] 10 PMC1_IO[10] 41 PMC1_IO[41] 42 PMC1_IO[42]
11 PMC1_IO[11] 12 PMC1_IO[12] 43 PMC1_IO[43] 44 PMC1_IO[44]
13 PMC1_IO[13] 14 PMC1_IO[14] 45 PMC1_IO[45] 46 PMC1_IO[46]
15 PMC1_IO[15] 16 PMC1_IO[16] 47 PMC1_IO[47] 48 PMC1_IO[48]
17 PMC1_IO[17] 18 PMC1_IO[18] 49 PMC1_IO[49] 50 PMC1_IO[50]
19 PMC1_IO[19] 20 PMC1_IO[20] 51 PMC1_IO[51] 52 PMC1_IO[52]
21 PMC1_IO[21] 22 PMC1_IO[22] 53 PMC1_IO[53] 54 PMC1_IO[54]
23 PMC1_IO[23] 24 PMC1_IO[24] 55 PMC1_IO[55] 56 PMC1_IO[56]
25 PMC1_IO[25] 26 PMC1_IO[26] 57 PMC1_IO[57] 58 PMC1_IO[58]
27 PMC1_IO[27] 28 PMC1_IO[28] 59 PMC1_IO[59] 60 PMC1_IO[60]
29 PMC1_IO[29] 30 PMC1_IO[30] 61 PMC1_IO[61] 62 PMC1_IO[62]
31 PMC1_IO[31] 32 PMC1_IO[32] 63 PMC1_IO[63] 64 PMC1_IO[64]

Handling and Installation 14
1.5.1 Serial Port Connectors and Pinouts (P9 and P10)
Figure 1-8 Serial Port Connectors (P9 and P10)
1.5.2 Jumper Configuration for Different Serial Modes
EachCOMportcanbesettooneoftwodifferentmodes,RS232orRS422/485,and
areindependentofeachother.Table1‐5belowdescribesthevariousjumper
configurationsneededtoobtaineachmode.Alongwiththejumper
configuration,switch(S1)ontheVMICPCI‐7055/CPCI‐7055RC(ProductManual,
DocumentNumber500‐657055‐000fordetails) mustbesetaccordinglyaswell.
NOTE
Defaults are in bold.
NOTE
To configure the serial ports for loopback mode, S1 on the VMICPCI-7055/CPCI-7055RC (Product
Manual, Document Number 500-657055-000 for details) will need pins 6 and 8 (relating to COM 1
and COM 2 respectively) placed in the ON position.
Table 1-4 Serial Port (P9/P10) Pinout
RS232 RS422/485
Pin # Signal Name Pin # Signal Name
1DCD 1RXD-
2RXD 2RXD+
3TXD 3TXD+
4DTR 4RTS-
5 GND 5 GND
6DSR 6CTS-
7RTS 7RTS+
8 CTS 8 CTS+
9RI 9TXD-
Table 1-5 Jumper Configurations for Different Serial Modes
COM Port Mode Selection S1 Pin# S1 Pin Position E5 E6 E7 E8
1RS232 5 OFF OMIT NA 3-4 NA
RS422/485 5 ON 1-2, 3-4 NA 1-2 NA
2
RS232 7 OFF NA OMIT NA 3-4
RS422/485 7 ON NA 1-2, 3-4 NA 1-2
Pin 9
Pin 1

Handling and Installation 15
Figure 1-9 Serial Header Signals
1.5.3 CompactFlash Connector and Pinout (P6)
Figure 1-10 CompactFlash Connector (P6)
E5
SP1_RXD- 1 2 SP1_RXD+
SP1_CTS- 34 SP1_CTS+
E6
SP2_RXD- 1 2 SP2_RXD+
SP2_CTS- 34 SP2_CTS+
E7
SP1_TXD- 1
RI_A 34 SP1_CTS_RI+
2 SP1_CTS_RI+
E8
SP2_TXD- 1
RI_B 34 SP2_CTS_RI+
2 SP2_CTS_RI+
Table 1-6 CompactFlash (P6) Pinout
Pin # Signal Name Pin # Signal Name Pin # Signal Name Pin # Signal Name
1 GND 14 GND 27 IDES_D[11] 40 N/C
2 IDES_D[3] 15 GND 28 IDES_D[12] 41 IDES_RESET#
3 IDES_D[4] 16 GND 29 IDES_D[13] 42 IDES_IORDY
4 IDES_D[5] 17 GND 30 IDES_D[14] 43 IDES_DMARQ
5 IDES_D[6] 18 IDES_DA2 31 IDES_D[15] 44 IDES_DMACK#
6 IDES_D[7] 19 IDES_DA1 32 IDES_CS3# 45 HD_ACTA#
7 IDES_CS1# 20 IDES_DA0 33 N/C 46 IDES_CBLIO#
8 GND 21 IDES_D[0] 34 IDES_DIOR# 47 IDES_D[8]
9 GND 22 IDES_D[1] 35 IDES_DIOW# 48 IDES_D[9]
10 GND 23 IDES_D[2] 36 5 VDC 49 IDES_D[10]
11 GND 24 N/C 37 IDES_INTRQ 50 GND
12 GND 25 N/C 38 5 VDC 51 GND
13V5.0 26 N/C 39CF_MASTER# 52GND
Pin #1

Handling and Installation 16
1.5.4 CompactFlash Master and Slave (Jumper E4)
WhentheIDEdriveandCompactFlashareinstalledatthesametime,oneofthem
mustbesetasaslave.
NOTE
The default setting is in bold.
Figure 1-11 CompactFlash Master and Slave Jumper (E4)
1.5.5 Gigabit LAN Port Connectors and Pinouts (J6 and J7)
AlthoughthetwoGigabitEthernetconnectorsareavailableonthe
VMIACC‐7055/ACC‐7055RC,theycanonlybeusedwhentheVMICPCI‐7055/
CPCI‐7055RChasavalueofʹ1ʹintheoptionsʹDfield,whichallowsforEthernet
viaCompactPCIJ3(notPICMG2.16compatible).
Table 1-7 CompactFlash Master and Slave (Jumper E4)
Master Slave
E4 Installed Omitted
Represents
the jumper

Handling and Installation 17
Figure 1-12 Ethernet Connector
Table 1-8 Ethernet Connectors LAN1 and LAN2 Pinout
s
LAN1 and LAN2
Pin No. Signal Name
1MDI[0]+
2MDI[0]-
3MDI[1]+
4MDI[2]+
5MDI[2]-
6MDI[1]-
7MDI[3]+
8MDI[3]-
Connector Opening
Pin#1
Top View

Handling and Installation 18
1.5.6 J3 Connector Pinout
TheJ3connectorisa5row,19pinseach,2mm“HardMetric”CompactPCI
connector.Anadditionalexternalmetalshieldisalsoused,labeledrowF.
Figure1‐13andTable1‐9illustratetheJ3connectorandtheconnectorpinout.
ThisconnectorisusedtoroutetheserialandEthernetsignalstothebackplane
I/O.
Figure 1-13 J3 Connector
Table 1-9 J3 Connector Pinout
Pin
No. Row A Row B Row C Row D Row E Row F
19 GND GND GND GND GND GND
18 LPA_BI_DA+ LPA_BI_DA2- GND LPA_BI_DC+ LPA_BI_DC- GND
17 LPA_BI_DB+ LPA_BI_DB2- GND LPA_BI_DD+ LPA_BI_DD- GND
16 LPB_BI_DA+ LPB_BI_DA2- GND LPB_BI_DC+ LPB_BI_DC- GND
15 LPB_BI_DB+ LPB_BI_DB2- GND LPB_BI_DD+ LPB_BI_DD- GND
14 GND GND GND GND GND GND
13 SP2_RTS SP1_RI SP2_DSR SP2_DCD SP2_CTS GND
12 SP1_RTS SP2_DTR VCC_5.0 SP1_CTS GND GND
11 SP2_TXB SP2_RXD SP1_DTR SP1_DCD LPA_BI_DC- GND
10 SP1_TXB SP1_RXD SP1_DSR SP2_RI LPA_BI_DD2- GND
9 GND GND N/C GND LPB_BI_DC2- GND
8 LPA_BI_DA2+ LPA_BI_DA2- SP2_ACTIVE LPA_BI_DC2+ LPB_BI_DD2-] GND
7 LPA_BI_DB2+ LPA_BI_DB2- SP2_LOOPBACK LPA_BI_DD2+ GND GND
6 LPB_BI_DA2+ LPB_BI_DA2- SP2_R485/232 LPB_BI_DC2+ GND GND
5 LPB_BI_DB2+ LPB_BI_DB2- SP1_ACTIVE LPB_BI_DD2+ N/C GND
4 GND GND VCC_5.0 GND VCC_3.3 GND
3 G1_Y_LINK100# G1_G_LK1000# SP1_R485/232 GND VCC_3.3 GND
2 G1_G_LINK10# G1_Y_ACT SP1_LOOPBACK G2_Y_LINK100# G2_G_LK1000# GND
1 N/C N/C N/C G2_G_LINK10# G2_Y_ACT# GND

Handling and Installation 19
1.5.7 J5 Connector Pinout
TheJ5connectorisa5row,22pinseach,2mm“HardMetric”CompactPCI
connector.Anadditionalexternalmetalshieldisalsoused,labeledrowF.
Figure1‐14andTable1‐10illustratetheJ5connectorandtheconnectorpinout.
The64‐bitPMCI/OisroutedthroughtheJ5toaPIMconnectorandtheIDE
signals.
Figure 1-14 J5 Connector
Table 1-10 J5 Connector Pinout
Pin
No. Row A Row B Row C Row D Row E Row F
22 PMC1_IO[5] PMC1_IO[4] PMC1_IO[3] PMC1_IO[2] PMC1_IO[1] GND
21 PMC1_IO[10] PMC1_IO[9] PMC1_IO[8] PMC1_IO[7] PMC1_IO[6] GND
20 PMC1_IO[15] PMC1_IO[14] PMC1_IO[13] PMC1_IO[12] PMC1_IO[11] GND
19 PMC1_IO[20] PMC1_IO[19] PMC1_IO[18] PMC1_IO[17] PMC1_IO[16] GND
18 PMC1_IO[25] PMC1_IO[24] PMC1_IO[23] PMC1_IO[22] PMC1_IO[21] GND
17 PMC1_IO[30] PMC1_IO[29] PMC1_IO[28] PMC1_IO[27] PMC1_IO[26] GND
16 PMC1_IO[35] PMC1_IO[34] PMC1_IO[33] PMC1_IO[32] PMC1_IO[31] GND
15 PMC1_IO[40] PMC1_IO[39] PMC1_IO[38] PMC1_IO[37] PMC1_IO[36] GND
14 PMC1_IO[45] PMC1_IO[44] PMC1_IO[43] PMC1_IO[42] PMC1_IO[41] GND
13 PMC1_IO[50] PMC1_IO[49] PMC1_IO[48] PMC1_IO[47] PMC1_IO[46] GND
12 PMC1_IO[55] PMC1_IO[54] PMC1_IO[53] PMC1_IO[52] PMC1_IO[51] GND
11 PMC1_IO[60] PMC1_IO[59] PMC1_IO[58] PMC1_IO[57] PMC1_IO[56] GND
10 VCC_5.0 PMC1_IO[64] PMC1_IO[63] PMC1_IO[62] PMC1_IO[61] GND
9 IDES_DA0 GND GND IDES_DA2 N/C GND
8 IDES_DA1 IDES_D[8] IDES_IORDY IDES_D[0] N/C GND
7 IDES_DIOR# IDES_D[9] IDES_CS1# IDES_D[1] VCC_5.0 GND
6 IDES_DIOW# IDES_D[10] HD_ACTA# IDES_D[2] N/C GND
5 N/C IDES_D[11] IDES_CS3# IDES_D[3] GND GND
4 IDES_CBLIO# IDES_D[12] IDES_INTRQ IDES_D[7] N/C GND
3 N/C IDES_D[13] IDES_DMACK# IDES_D[6] N/C GND
2 N/C IDES_D[14] IDES_DMARQ IDES_D[5] VCC_3.3 GND
1 N/C IDES_D[15] IDES_RESET# IDES_D[4] N/C GND
SHIELD
A B C D E
22
20
18
16
14
12
10
8
6
4
2
F
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

Maintenance 20
Maintenance
IfaGEproductmalfunctions,pleaseverifythefollowing:
1.Softwareversionresidentontheproduct
2.Systemconfiguration
3.Electricalconnections
4.Jumperorconfigurationoptions
5.Boardsarefullyinsertedintotheirproperconnectorlocation
6.Connectorpinsarecleanandfreefromcontamination
7.Nocomponentsoradjacentboardsweredisturbedwheninsertingorremov‐
ingtheboardfromthechassis
8.QualityofcablesandI/Oconnections
Ifproductsmustbereturned,contactGEforaReturnMaterialAuthorization
(RMA)Number.ThisRMANumbermustbeobtainedpriortoanyreturnfrom
CustomerCare.
GECustomerCareisavailableat:1‐800‐433‐2682inNorthAmerica,
or+1‐780‐401‐7700forinternationalcalls.Or,visitourwebsitewww.ge‐ip.com.
Maintenance Prints
Userlevelrepairsarenotrecommended.Thedrawingsanddiagramsinthis
manualareforreferencepurposesonly.