GE Albeo ALR1 Series User manual

imagination at work
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL or IEC approved wire for input/output connections.
Minimum size 18 AWG.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de
connexion. Taille minimum 18 AWG.
GE
Lighting
Installation Guide
Linear Lighting
(ALR1 Series)
AlbeoTM LED Luminaire
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Prepare Electrical Wiring
Electrical Requirements
• The LED luminaire must be connected to the mains supply
according to its ratings on the product label.
Grounding Instructions
• The grounding and bonding of the overall system shall be
done in accordance to local electric code of the country where
the luminaire is installed.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Tools and Components Required:
• ALR1 Series xture
• Mounting hardware (not Included)
• #2 Phillips screwdriver
• Drill
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

Mount the wrap-around brackets on the ceiling or support rail using appropriate hardware. After brackets are
secured in place, install one side of the housing in the bracket, then rotate up and snap the other side of the
housing into bracket. Chain and “S” hook (not included) can also be used to support the brackets
1
Installation
Unfasten the latches and remove the lens.
2 3
Housing (1)
Lens (1)
Driver enclosure (1)
LED driver (2)
LED strip (1)
Housing latches (6)
Mounting brackets (2)
Endplug (1)
Components Included
5
6
7
8
4
3
2
1
5
6
78
4
3
2
1
Chain and “S” hook
Squeeze the enclosure at the end and remove
LED stip.

Lift LED strip from housing and disconnect from
the LED driver.
4Connect a rigid conduit or exible conduit or
strain relief and feed the AC line wire through
the tting.
5
Connect the AC line to the black (line) and white
(neutral) input wires of the LED driver using
14-18AWG twist-on wire connectors. Connect the
ground wire to the green grounding wire.
Rigid conduit Flexible conduit Strain relief
6Reconnect similarly-colored wires from LED driver
to LED strip. Then reattach the LED strip making
sure the two end clips are properly engaged.
7
Reinstall the lens and secure the latches.
8

Wiring Diagram
Red (+)
Blue (-)
Violet (+)
Gray (-)
Black (L)
White (N) LED Driver
Line
Neutral
Ground
Ground screw on driver enclosure
Dimming control
(optional)
LED Strip
www.gelighting.com
GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory conditions. GE Lighting is a business of the General Electric Company. © 2017 GE.
ALB022 (Rev 09/07/17)