GE Lumination LVT 24 Series User manual

GE
Lighting
Installation Guide
imagination at work
(LVT Series, 120-277V and 347V)
LuminationTM LED Luminaires
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.75mm2).
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion.
Taille minimum 18 AWG (0.75mm2).
LVT 24 Series LVT 22 Series LVT 14 Series
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Components Supplied
Prepare Electrical Wiring
Tools and Components Required
Electrical Requirements
•The LED luminaire must be connected to the mains supply
according to its ratings on the product label.
Grounding Instructions
•The grounding and bonding of the overall system shall
be done in accordance with National Electric Code (NEC)
Article 600 and local codes.
•Slot or Philips screwdriver
•UL Listed conduit connections per NEC/CEC for nominal
conduit trade sizes ½” or ¾”
•UL Listed wire connectors
•Luminaire

Luminaire Installation
Electrical Connections
Bend the 4 clips to secure the luminaire in place.
Install the safety cables through the holes on the clips
(per local building codes, safety cables by others).
Install the unit into the reserved hole in the ceiling.
3
1 2
Carefully unpack unit from its packaging. Properly
inspect for defects before installing. Wear work
gloves to prevent dirt and oil from being transferred
to the luminaire.
Safety cable
WARNING/AVERTISSEMENT
Risk of electrical shock. Disconnect power before servicing or installing product.
Risque de choc électrique. Couper l’alimentation avant le dépannage ou avant l’installation du produit.
120-277V
WHITE COMMON
NEUTRAL
BLACK UNSWITCHED
LINE
GROUND GROUND
GREY DIMMING
0-10V
DIMMING (••)
VIOLET DIMMING (+)
Exterior Wires Exterior Wires
Back-Lit Recessed Troffer Module Back-Lit Recessed Troffer Module
347V
RED COMMON
NEUTRAL 347V
BLACK UNSWITCHED
LINE 347V
GROUND GROUND
GREY DIMMING
0-10V
DIMMING (••)
VIOLET DIMMING (+)
The diffuser panel is engaged over 4 screws on both
ends of the LVT luminaire. It may become loose during
shipping or if the lumiare is signifcantly twisted during
install. It is important to make sure the diffuser is
completely engaged to avoid having it fall out after the
install is complete. Grasp diffuser and gently squeeze
together to re-engage over screws.
4
Diffuser panel
Screw is engagedScrew is disengaged
Squeeze

Remove electrical enclosure cover. Remove
knockout for AC line input wires.
1Install listed electrical ttings in the knockout
holes for wire protection. Connect the AC line
to the luminaire internal wires according to the
wiring diagrams using 18-14AWG twist-on wire
connectors.
2
Install listed electrical ttings in the knockout holes
for wire protection. Connect the dimming control
(grey and purple or purple and purple/white) wires
of the LED driver using 18-14AWG twist-on wire
connectors.
3Replace electrical enclosure cover and secure
it with the screw.
4
Dimming line
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class [A] RFLD complies with the
Canadian standard ICES-003. Ce DEFR de la classe [ A ] est conforme à la NMB-003 du Canada.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
AC line
www.gelighting.com
GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory conditions. GE Lighting is a business of the General Electric Company. © 2016 GE.
IND299 (Rev 10/19/16)