GE IP180 Series User manual

GE
Lighting Solutions
imagination at work
(IP180 Series)
Features
• 0-10V & DALI control (optional)
• Long life (50,000 hour rated life)
• 5 year warranty
• Dry location rated
GE LED Luminaire
Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• The LED driver must be supplied with 100-277 VAC, 50/60 Hz and connected to an individual properly
grounded branch circuit, protected by a 15 or 20 ampere circuit breaker. Use min. 75°C supply conductor.
Grounding Instructions
• The grounding and bonding of the overall system shall be done in accordance with National Electric Code
(NEC) Article 600 and local codes.
Tools and components required:
• #2 Phillips head screwdriver.
• UL Recognized conduit connections per NEC/CEC for nominal conduit trade sizes ½” or ¾”.
• UL Recognized wire connectors.

The luminaires come as a separate master luminaire and a satellite luminaire which must always be installed as a pair. When installing
multiple pairs always ensure that adjacent luminaire are of alternating types. The master luminaire differs from the satellite luminaire in
that it has an LED driver. No more than one satellite luminaire can be used with each master luminaire.
Unit Installation
Align tabs with slots
Run electrical quick connectors through the through-hole
of the two luminaires. Click the male 6-pin connector
of the master luminaire to the female connector of the
satellite luminaire. Ensure the locking feature on the
connectors is rmly engaged.
NOTE: A maximum of seven master luminaires and seven
satellite luminaires (112 ft.) can be connected on a single
through wiring run.
IMPORTANT: If the xtures do not have mating
connectors then one has been installed the wrong way
around. Reinstall the incorrect xture before proceeding.
Master luminaire
Satellite luminaire
2Suspend the satellite luminaire adjacent to the master
luminaire according to the installation instructions of
the selected suspension method before attempting to
perform any electrical interconnections.
1Carefully unpack unit from its packaging. Properly inspect
for defects before installing. Wear work gloves to prevent
dirt and oil from being transferred to the luminaire.
4
6
3
5
Temporarily align two adjacent luminaires by sliding the
tabs into the corresponding slots.
Optional Continuous Run Mounting:
When connecting luminaires in a continuous run, each
master/satellite combination is followed by an additional
pair(s). Ensure electrical connections are secure and
alignment tabs and joiner brackets are securely
fastened between each xture in the run. Install end
caps (End Cap Kit 69074) to rst and last xtures in runs.
Refer to install instructions in end cap kit (69074) for
proper installation.
Conceal wires and connection between the luminaires by
sliding two joiner covers (provided in Joiner Kit 69073) over
the LED light engine so that they engage with a click.
Use bracket from Joiner Kit (69073) to attach luminaires
by inserting the curved lower tabs into the slots at the
base of the luminaire and rotate the bracket so the
upper tabs slide into the slots at the top of the luminaire.
Install the two screws (provided in Joiner Kit) with a
Phillips head screwdriver.

Electrical Connections
DALI
Fixture
Neutral
Ground
Line
DALI
DALI
White
Green
Black
Violet/White
Violet
0-10V
Fixture
Neutral
Ground
Line
(0-10V) +
(0-10V) –
White
Green
Black
Violet
Grey
2
4
Carefully remove appropriate knockout for AC line input
wires (inner knockout for ½” conduit, outer knockout
for ¾” conduit). Install listed electrical ttings in the
knockout holes for wire protection and pass supply
conduit through electrical ttings.
Optional dimmer: Install UL listed electrical tting and
insert dimming control wires through. Connect dimming
control wires (grey and violet for 1-10V or violet and
violet/white strip for DALI) to the similarly colored xture
wire using the provided push-in wire-nuts.
1
3
5
Remove knockout plate from luminaire by loosening the
knockout screw and sliding the cover out of luminaire.
Connect the green (ground) wire to the green ground
wire of the luminaire using the provided push-in wire-
nut. Connect the black (line) and white (neutral) wires
of the AC line to the black and white wires of the power
supply unit using the provided push-in wire-nuts.
Carefully push the wire bundle back into the body of the
luminaire. Replace plate and re-tighten mounting screw.
Wiring Diagrams

IND045-121712
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 - 8 8 8 - 6 9 - 4 3 - 5 3 3
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. The GE brand and logo are trademarks of the General Electric Company.
© 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
Specications
Input Voltage 120 – 277V
Input Power (complete system)/8 ft. 80W
Input Frequency 50/60Hz
Power Factor >0.9
THD <20%
Control 0-10V/DALI
Warranty 5 year limited warranty
Dimensions 1 ft. x 8 ft. x 5 in.
Environmental Operating Temperature Range -10°C to +25°C
Environmental Humidity (non-condensing) 20 to 80% Non-condensing, dry location rated
Environmental Storage Temperature Range -40°C to +60°C
Weight/8 ft. <35 lbs.
Environmental Rating Dry Location
Troubleshooting
Conforms to the following standards:
Symptom Solution
Luminaires will not turn on • Check that the color of the supply side wires match the color of the wires they are connected to.
• Check that the LED driver connector is fully engaged to the LED light engine connector.
• Check that the LED light engines are connected at the juction between the two luminaires.
Luminaire on through wiring will
not turn on
• Check that the through wiring connector from the previous xture in the linear row is fully
engaged to the malfunctioning luminaire.
Joiner bracket will not t
between two luminaires in a
continuous row
• Check that the mating tabs between the luminaires are fully engaged.
• Check that the two luminaires are on the same level with one another and there is no angle
between them.
Joiner covers will not click
together
• Check that the joiner covers are a slot and tab pair not two slotted or two tabbed pieces.
• Check that the internal wiring is not in the way of the joiner covers.
Suspension method won’t
engage with luminaire
• Check that the suspension method is one of the approved types in the installation instruction.