GE Lumination LPL GenB Series User manual

LuminationTM LED Luminaires
LPL GenB Series
Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation or
removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output
connections. Minimum size 18 AWG (0.75mm2).
Prepare Electrical Wiring
Electrical Requirements
• The LED luminaire must be connected to the mains
supply according to its ratings on the product label.
• Class 1 wiring should be in accordance with NEC.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance to local electric code
of the country where the luminaire is installed.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation
électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.75mm2).
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-005(A)/NMB-005(A)
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Tools and Components Required
• Screwdriver
• UL approved conduit ttings
• UL approved twist-on wire connectors
1

and blue wires from the driver to the light engine.
housing, please make sure no wires are pinched by the driver box. Connect the quick connector with the red
into the embosses on the light engine housing. Before secure the box with the captive screw to the light engine
the cavity. The green-yellow ground wires should also be fed in to the same hole. Insert the driver box tabs
connector from the light engine should be fed through the square hole on the bottom of the driver box in to
Luminaire Installation
Carefully unpack unit from its packaging. Properly
inspect for defects before installing. Wear work
gloves to prevent dirt and oil from being
transferred to the luminaire.
1
Remove the xture and driver box from the
package. If a lumen level other than M (medium)
is desired, remove switch cover and set to the
desired lumen level and re-attach cover.
2
L M H
2BY2: 2450lm 3750lm 4500lm
2BY4: 3500lm 4550lm 5250lm
Loosen the screw on the driver box cover and open the electrical cavity.The red and blue wires with a
3
Switch
1
2
3
4
2

Insert the luminaire into the T-grid ceiling. Unit should not move freely within the ceiling grid.
4
Bend the brackets on the back plate to make sure
they hook to T-Bar.
Secure safety cable to connection hole as needed to
meet local seismic requirements. Safety cable and
method of attachment to the building are provided
by contractor according to local building codes.
5
Bracket on back
plate
T-Bar
Safety cable hole
LPL 2X2 SERIES LPL 2X4 SERIES
3

www.led.com
GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property
of their respective owners. Information provided is subject to change without notice. All values are design or typical
values when measured under laboratory conditions. GE Lighting and GE Lighting Solutions, LLC are businesses of
the General Electric Company. © 2019 GE.
IND533 (Rev 10/23/19)
Electrical Connections
Carefully remove knockout for AC line input
wires. Install listed electrical ttings in the
knockout holes for wire protection.
1Connect the AC line to the black (line) and
white (neutral) input wires of the LED driver.
Connect the ground wire to the
green-yellow ground wire of the LED driver.
When connecting the dimming control
wires, they must run through a separate
knockout hole. Wiring requires an
appropriate wire restraint.
2
Secure the enclosure cover with the captive screw that is attached to the cover after wiring is complete.
3
Option for Step 2: Follow diagram for 0-10V. Run wires from controller through a dierent knockout than
the AC input wire. At output side of xture, make appropriate connections using twist-on wire connectors.
To combine with LFAMBA0VQFAEL, LCAMBA0NRFAEL, LCAMBA0TSFAEL, LCAMBA0TQFAEL, LFAMBADVQFA,
LCAMBA0NRFAB2, LCAMBA0TSFAB2, LCAMBA0TQFAB2, LCAMBA0NRFA, LCAMBA0TSFA, LCAMBA0SQFA or
LCAMBA0TQFA, please follow the install instructions provided with those products.
4
NOTE: Please cover dimming leads with wire nuts if you will not connect with dimming leads.
AC Line
To dimming controller