GE Lumination BL44 Series User manual

GE
Lighting Solutions
imagination at work
(BL44 and BL45 Series)
Features
• Long life (50,000 hour rated life)
• 5 year warranty
• IP30
LuminationTM LED Luminaires
Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all IEC and local codes.
• Use only UL or IEC approved wire for input/output connections.
Minimum size 18 AWG (0.82mm2).
• Product not IC rated.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes IEC et codes locaux.
• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.82mm2).
• Le produit n’est pas classé IC.
Prepare Electrical Wiring
Electrical Requirements
• The LED driver must be supplied with 100-277 VAC, 50/60 Hz and connected to an individual properly
grounded branch circuit, protected by a 15 or 20 ampere circuit breaker. Use min. 75°C supply conductor.
Grounding Instructions
• The grounding and bonding of the overall system shall be done in accordance with National Electric Code
(NEC) Article 600 and local codes.

2
3A 3B
Remove end cover closest to the cable glands.
Two diffusers: Slide both diffusers into base of
luminaire, making sure the diffuser with the green
protective lm is placed on the bottom with the lm
facing towards the outside.
One diffuser: Slide diffuser into base of luminaire.
1Carefully unpack unit from its packaging. Properly
inspect for defects before installing. Wear work gloves
to prevent dirt and oil from being transferred to the
luminaire.
Electrical Connections
Dimming line
(optional)
AC line
AC line
2
1Connect the green wire of the AC line to the middle
position on the terminal block. Connect brown or black
(line) wire to the L1 position and the blue (neutral) wire to
the N position.
Loosen cable gland nuts to insert AC line. Optionally, insert
dimming line into smaller cable gland.
Optional Installation: Diffuser
Bottom: Diffuser with
green lm faces down
(will be removed later)
Top: Diffuser with no lm
Two diffusersOne diffuser
Unpacking

Dimming line
(optional)
3Optional: If using a dimmer, connect black and red wires
of the dimming line to the D1 and D2 positions on the
terminal block.
2
1Fasten mounting brackets over screws but do not
tighten them at this point. Note that bracket aps have
to be aligned with the groove.
Slide two bracket mounting screws into housing groove
on each side (four screws per housing). If the screw head
cannot pass through end cover groove, remove end covers
and slide the screw head directly into the housing groove,
then re-install end covers.
Luminaire Installation
Follow diagram A for 0-10V or diagram B for DALI. Run wires from controller through a different knockout than the AC input wire.
At output side of LED Driver, make appropriate connections using twist-on wire connectors. Follow lighting controller installation
instructions.
BLU/WHT
BLK/WHT
YEL
GRY
VIO
VIO/WHT
LED Driver
To 0-10V
Dimmer
0-10V -
0-10V +
BLU/WHT
BLK/WHT
YEL
GRY
VIO
VIO/WHT
LED Driver
To DALI
Controller
DALI/Prog
DALI/Prog
BDALI controller wiring diagram A0-10V dimmer wiring diagram
Optional Installation: 0-10 Volt Dimming or DALI Lighting Controller
4Replace cover using at least one star washer under
countersunk screwhead.
Star washer
Do not
tighten yet

Conforms to the following standards:
5For added safety, use additional screw to permanently x
bracket to grid. Optionally, mounting brackets can be xed
directly to the roof with appropriate mounting wire and
hardware (not included).
6After installation, remove green protective lm from the
diffuser if applicable.
4
3Using a 5.5mm socket wrench, gently tighten nuts on
mounting brackets, being careful not to strip the threads.
Mount xture into grid system. The brackets should be
15–20cm (6–8 in.) from the ends.
IND035-100412
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 - 8 8 8 - 6 9 - 4 3 - 5 3 3
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Lumination is a trademark of GE Lighting Solutions, LLC. The GE brand and logo are trademarks of the General Electric Company.
© 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
Specications
High Lumen Output Series Medium Lumen Output Series
Input Voltage 120 – 277V 120 – 277V
Input Power/foot (complete system) 9W 6W
Input Frequency 50/60Hz 50/60Hz
Power Factor >0.9 >0.9
CCT 3000K, 3500K, 4000K 3000K, 3500K, 4000K
Color Consistency 4-step 4-step
CRI 83 83
THD <20% <20%
Control 0-10V/DALI 0-10V/DALI
Warranty 5 years 5 years
Mounting Recessed system - A type grids Recessed system - A type grids
Environmental Operating Temperature Range -10°C to +40°C -10°C to +40°C
Environmental Humidity (non-condensing) 20 to 80% Non-condensing, dry location rated 20 to 80% Non-condensing, dry location rated
Environmental Storage Temperature Range -40°C to +60°C -40°C to +60°C
Weight <7 kg <8 kg
IP Rating IP30 IP30
Screw for safety
Ceiling
Remove green
protective lm
15-20cm