Genaray LED-6500T User manual

USER MANUAL
LED-6500T
209 LED VARIABLE COLOR ON-CAMERA LIGHT

Thank you for choosing the Genaray LED-6500T
On-Camera Light. This product will provide you with
powerful, portable and dependable illumination that
can be used in a variety of settings. Featuring a
super-bright 209 LED lamp count, 3200K-5600K
variable color temperature, flicker-free dimmable
features and a removable magnetic diffuser with
advanced light dispersion capabilities, the Genaray
LED-6500T On-Camera Light is the perfect choice for
professional photographers and videographers alike.
LED-6500T - USER MANUAL
2
LED-6500T
INTRODUCTION

· 3200K-5600K Variable Color
Temperature
· Lightweight Design With
Powerful 209 Lamp Count
· Compact Profile & Case
For Easy Transport
· Removable Snap-On
Magnetic Diffuser
· Built-In Battery Life Indicator
· Vertically Stackable
· 209 LED Light
· Magnetic Diffuser
· NP-F550 Battery
· AC/DC Battery Charger
· AC Adapter
· Car Adapter
· Ball Head Mount
· Carrying Case
· Manual
KEY FEATURES PRODUCT CONTENTS
LED-6500T - USER MANUAL
3
FEATURES

SAFETY
WARNINGS
· Do not attempt to disassemble,
repair or perform any unauthorized
modifications on device
· Do not handle with wet hands,
immerse in liquids or expose to water
and rain; electric shock or fire may
result
· Device contains small parts which
may pose a choking hazard; keep out
reach of children
· Do not operate device in presence of
flammable gas or vapors
· Do not use product if it emits smoke
or a strange odor; disconnect power
source immediately to avoid personal
injury and contact place of purchase
· Observe caution when handling
batteries; only use batteries approved
by the manufacturer of this product
· Batteries are prone to leakage when
fully discharged; to avoid damaging
product be sure to remove batteries
when leaving product unattended
· Do not intentionally stare or gaze at
LED-6500T - USER MANUAL
4
SAFETY WARNINGS

LED light for prolonged periods while
device is on
· During operation, do not cover the
ventilation grille found at the rear of
device and ensure light is cool before
storing
· Do not use or leave device in
conditions of extreme heat, severe
cold or high humidity
· Unit will display a decrease in
brightness when the battery runs
low; be sure to replace battery when
necessary to avoid affecting recording
quality
· When cleaning the device, use only a
mild detergent solution and quickly
wipe dry with a soft cloth
· Dispose of used batteries, packaging
and old devices in accordance
with appropriate environmental
regulations
LED-6500T - USER MANUAL
5
SAFETY WARNINGS

Filter
Mounting
Magnet
LED Array Included
Ball Head
Mount
1/4 20
Threaded Mount
PRODUCT
OVERVIEW
LED-6500T - USER MANUAL
6
Stacking
Release
Button

Battery
Mounting
Area
Battery
Release
Button
Power &
Dimming
Knob
Color
Variation
Knob
Battery Level
Indicator DC
Input
LED-6500T - USER MANUAL
7
Stacking
Rail Slots
PRODUCT OVERVIEW

MOUNTING LIGHT
UNIT DIRECTLY ON
TRIPOD
MOUNTING LIGHT
UNIT ON BALL HEAD
MOUNT
· For tripod installation, simply insert 1/4 20
screw found on tripod head into the 1/4 20
threading mount found on bottom of unit;
then tighten securely
Light can also be fastened
to included ball head mount,
which can then be installed on
cold shoe found on cameras
or similar devices; see ball
head mounting instructions
· Included ball head mount is designed to
provide user with a 180° tilt/360° rotating
angle feature that can be used on both
cameras and other devices featuring a cold
shoe
· Begin by inserting 1/4 20 screw found atop ball
head mount into the 1/4 20 threading found on
bottom of LED light unit and fasten securely
· Tighten adjustment locking knob so light
unit does not wobble during remainder of
mounting process
· Ensure cold shoe foot is firmly secured to ball
head mount device and loosen locking collar
found on base of ball head device
· Slide entire male cold shoe into female cold
shoe of camera or other mounting device; then
fasten locking collar securely
Note
LED-6500T - USER MANUAL
8
INSTRUCTIONS

· Loosen adjustment locking knob by
twisting counterclockwise and rotate ball
head mount to position light at desired
angle; twist locking knob clockwise to hold
light unit firmly in position
Cold shoe mount can also
be removed to reveal an
integrated1/4 20 threading
mount
· To reveal ball head mount's integrated 1/4
20 threading mount for fastening to tripod,
twist locking ring resting above cold shoe
counterclockwise until entire shoe comes
out; insert 1/4 20 screw found on tripod
head into the 1/4 20 threading mount; then
tighten securely
INTERLOCKING
WITH OTHER LED
DEVICES
· Slide stacking rail slots into expansion
slots of another compatible Genaray LED
light device; click into place securely
· Up to 3 compatible Genaray LED light
devices can be mounted to each other in a
vertical format for increased illumination;
disengage stacked devices by pressing
release button
Note
LED-6500T - USER MANUAL
9
INSTRUCTIONS

POWERING
DEVICE
circles combined will represent a fully
charged battery
For an accurate reading of
battery levels, it is best to
turn off light unit before using
battery level indicator feature
· Rechargeable battery can be removed
by firmly pushing down on the battery
release button
· The DC input found on rear of device
connects directly to the included AC power
adapter or car charger and can provide
continuous power when battery is low or
not working
· Begin by holding fully-charged battery in
position over mounting area, leaving only
a small gap between conductor contacts
found on battery and metal prongs found
on unit
· Push battery down and lock into place by
sliding it inwards along grooves until an
audible click is heard
· Twist the power & dimming switch
clockwise to turn LED lights on
· Press the built-in battery level indicator
button to instantly view the power
remaining in the battery; each indicator
circle represents approximately 25%
of battery capacity; the showing of 4 lit
Note
LED-6500T - USER MANUAL
10
INSTRUCTIONS