Genaray LED-7500T User manual

USER MANUAL
LED-7500T
320 LED VARIABLE COLOR ON-CAMERA LIGHT

Thank you for choosing the Genaray LED-7500T
On-Camera Light. This product will provide you with
powerful, portable and dependable illumination that
can be used in a variety of settings. Featuring a super-
bright 320 LED lamp count, 2800K-6500K variable
color temperature, flicker-free dimmable features and
included diffusion filter with advanced light dispersion
capabilities, the Genaray LED-7500T On-Camera
Light proves to be the perfect choice for professional
photographers and videographers alike.
LED-7500T - USER MANUAL
2
LED-7500T
INTRODUCTION

· 2800K-6500K Variable Color
Temperature
· Lightweight Design With
Powerful 320 Lamp Count
· Long Profile Provides Wider
Angle Of Coverage
· Easily Removable Slide-In
Light Diffuser
· Low Battery Power Warning Light
· Vertically Stackable Features
· 320 LED Light
· Slide-In Diffuser
· NP-F750 Battery
· AC/DC Battery Charger
· AC Adapter
· Ball head Mount
· Manual
KEY FEATURES PRODUCT CONTENTS
LED-7500T - USER MANUAL
3
Features

SAFETY
WARNINGS
· Do not attempt to disassemble,
repair or perform any unauthorized
modifications on device
· Do not handle with wet hands,
immerse in liquids or expose to water
and rain; electric shock or fire may
result
· Device contains small parts which
may pose a choking hazard; keep out
reach of children
· Do not operate device in presence of
flammable gas or vapors
· Do not use product if it emits smoke
or a strange odor; disconnect power
source immediately to avoid personal
injury and contact place of purchase
· Observe caution when handling
batteries; only use batteries approved
by the manufacturer of this product
· Batteries are prone to leakage when
fully discharged; to avoid damaging
product be sure to remove batteries
when leaving product unattended
· Do not intentionally stare or gaze
LED-7500T - USER MANUAL
4
saFety Warnings

at LED light panel for prolonged
periods while device is on
· Do not cover the ventilation grille
found at the rear of device when in
operation and ensure light is cool
before storing
· Do not use or leave device in
conditions of extreme heat, severe
cold or high humidity
· Unit will display a decrease in
brightness when the battery runs
low; be sure to replace battery
when necessary to avoid affecting
recording quality
· When cleaning the device, use only a
mild detergent solution and quickly
wipe dry with a soft cloth
· Please dispose of used batteries,
packaging and old devices in
accordance with appropriate
environmental regulations
LED-7500T - USER MANUAL
5
saFety Warnings

PRODUCT
OVERVIEW
LED-7500T - USER MANUAL
6
Filter
Clasps
LED
Array Included
Ball Head
Mount
Cold Shoe Mount
1/4 20
Threading Mount

LED-7500T - USER MANUAL
7
Battery
Mounting
Area
Battery
Release
Button Power and
Dimming
Knob
Color
Variation
Knob
Interlocking
Expansion
Slot
Low
Battery
Level
Warning
Light
DC Input
PrODuCt OvervieW
Expansion
Slot Release
Tab

MOUNTING LIGHT
UNIT DIRECTLY ON
CAMERA OR TRIPOD
LED-7500T - USER MANUAL
8
· Begin by positioning light directly atop
camera or video camera
· Slide cold shoe mounting into shoe of
camera
· For tripod installation, simply insert 1/4 20
screw found on tripod head into the 1/4 20
threading mount found on bottom of unit;
then tighten securely
Light can also be fastened
to included ball head mount,
which can then be installed on
cold shoe found on cameras or
similar devices; see ball head
mounting instructions
Note
MOUNTING
LIGHT UNIT ON
BALL HEAD MOUNT
· Included ball head mount is designed to
provide user with a 180° tilt/360° rotating
angle feature that can be used on both
cameras and other devices featuring a cold
shoe
· Begin by inserting 1/4 20 screw found atop ball
head mount into the 1/4 20 threading found on
bottom of LED light unit and fasten securely
· Tighten adjustment locking knob so light
unit does not wobble during remainder of
mounting process
· Ensure cold shoe foot is firmly secured to ball
head mount device and loosen locking collar
found on base of ball head device
· Slide entire male cold shoe into female cold
shoe of camera or other mounting device; then
fasten locking collar securely
instruCtiOns

INTERLOCKING
WITH OTHER
LED DEVICES
LED-7500T - USER MANUAL
9
· Slide cold shoe mounting into
interlocking expansion slot of another
compatible Genaray LED light device
· To separate stacked units, press down
on the release tab found at the bottom
of the expansion slot to allow the cold
shoe of the other unit to slide out
· Compatible Genaray LED light devices
can be mounted atop one another in a
stacked vertical format for increased
illumination
· Loosen adjustment locking knob by
twisting counterclockwise and rotate ball
head mount to position light at desired
angle; twist locking knob clockwise to hold
light unit firmly in position
Cold shoe mount can also
be removed to reveal an
integrated1/4 20 threading
mount
· To reveal ball head mount's integrated 1/4
20 threading mount for fastening to tripod,
twist locking ring resting above cold shoe
counterclockwise until entire shoe comes
out; insert 1/4 20 screw found on tripod
head into the 1/4 20 threading mount; then
follow remaining adjustment steps above
Note
instruCtiOns

LED-7500T - USER MANUAL
10
POWERING
DEVICE
· Begin by holding fully-charged battery
in position over mounting area, leaving
only a small gap between conductor
contacts found on battery and metal
prongs found on unit
· Push battery down and lock into place
by sliding it inwards along grooves
until an audible click is heard
· The power port found on rear of
monitor connects directly to the
AC power adapter and can provide
continuous power in the event that the
battery is low
· Turn power and dimming dial to the
ON position and adjust to appropriate
light intensity
· Rechargeable battery can be removed
by firmly pushing down on the battery
release button and sliding the battery
to the side until it disengages
instruCtiOns

PRODUCT
SPECIFICATIONS
LED-7500T - USER MANUAL
11
ADJUSTING
FEATURES
· To adjust the 2800K-6500K
variable color temperature
range, simply rotate color
variation knob until desired
effect is achieved
· To install the diffusion filter,
align filter with posts found on
edge of LED light; ensure that
filter tab is on top and slide filter
alongside posts; gently snap
filter in place
CUSTOMER SUPPORT
For more information about this product or to
contact the Genaray Customer Support Center
with any questions, please send your email
correspondence to: [e-mail].
Bulb Type: 160 Daylight and 160 Tungsten LEDs
Brightness: 1500 lux @ 3'
Color Temperature: 2800K-6500K
Voltage: 6.5-12V
Weight: 0.76 lbs
Dimension: 10" x 4" x 2.25"
sPeCiFiCatiOns

ONE-YEAR LIMITED WARRANTY
Genaray provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a period
of one (1) year from the original purchase date or thirty (30) days after replacement,
whichever occurs later (the “Warranty Period”). Our responsibility with respect
to this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain warranty
coverage during the Warranty Period, contact your place of purchase (“Seller”) to
obtain a return merchandise authorization (“RMA”) number, and return to Seller the
defective product along with proof of purchase and the RMA number. This warranty
does not extend to damage or failure which results from misuse, neglect, accident,
alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED
HEREIN, GENARAY MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty
provides you with specific legal rights, and you may also have additional rights which
vary from state to state. © Copyright 2013 Genaray
www.genaray.com