GlammFire KIT Glamm 3D Plus 500 User manual

KIT Glamm 3D Plus 500 / 1000
(with water tank)
Capacity
1,3 liters / 2,6 liters (filtered water)
Autonomy
8 hours
Voltage
220/240 V
Frequency
50 Hz
Consumption
220 W / 440 W
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic
Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives
2006/95/EC and 2004/108/EC.

GlammFire. PAG./2

GlammFire. PAG./3
Index
1—Components 10
2—Important safety advice 11
3—General Information 12
4—Installation Instructions 12
4.1—Connections required in advance of Installation 12
4.2—Building the product surround/ enclosure 12
4.3—Ventilation 12
4.4—Electrical connection 13
4.5—Installing the product into surround/Enclosure 13
4.6—Comissioning/initial product start-up 13
4.7—Multiple product installation (daisy chaining) 14
5—Operanting the product 14
5.1—Manual controls 14
5.2—Receiver controls 15
5.3—Remote control 16
5.4—Getting the desired flame effect 17
5.5—Low water / Refilling the water tanks 17
6—Maintenence 17
6.1—General tips 17
6.2—Cleaning 18
7—Troubleshooting 19
8—General dimensions 20
9—After-sales service 20
10—Warranty 20
Congratulations on purchasing your GlammFire Electric appliance. This quality product has been designed with preci-
sion and rigour that characterizes us to offer you pleasant and soothing moments.
Please read the instructions for use carefully and effective before using the appliance.
Keep this Manual in a safe place.
Please read this manual before using your appliance and keep it for future reference. All presented warnings must be
respected.
The information provided in this manual is subject to change without notice.

Note: It’s importante that at least one side has openings to permit ventilation of the product.
Fig. 1
Finishings DIM ‘B’
Decorative lacquered steel 304
Decorative firewood 354
Min: 190 mm
Max: 260 mm
Model DIM ‘A’
Kit Glamm 3D Plus 500 508
Kit Glamm 3D Plus 1000 1017
Dimensions for installation
C
E
D
Model C D E
Kit Glamm 3D Plus 500 309 mm 230 mm 513 mm
Kit Glamm 3D Plus 1000 309 mm 230 mm 1022 mm
Kit Glamm 3D Plus 500
with decorative firewood
465 mm 230 mm 512 mm
Kit Glamm 3D Plus 1000
with decorative firewood
980 mm 230 mm 1021 mm

GlammFire. PAG./5

GlammFire. PAG./6
Fig. 5 Fig. 6
Fig. 7
Fig. 6B
Fig. 6A

GlammFire. PAG./7
Fig. 8

Fig. 9 Fig. 10
Fig. 11 Fig. 12A
Fig. 12B Fig. 13

GlammFire. PAG./9

GlammFire. PAG./10

GlammFire. PAG./11
Fig 23
Fig 24
Fig 27
Fig 25
Fig 26

GlammFire. PAG./12
1—Components
Decorative firewood
Tank
Sump
Model base

GlammFire. PAG./13
2—Important safety advice
Please read this information guide carefully to be able to safely install, use and maintain your product.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical
shock and injury to persons, including the following:
If the appliance is damaged, check with the supplier before installation and operation.
- Do not use outdoors;
- Do not use in the immediate surroundings of a bath, shower or swimming pool;
- Do not locate the appliance immediately below a fixed socket outlet or connection box.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been pla-
ced or installed in its intended normal operating position and they have been given supervision or instruction concer-
ning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than
8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given whe-
re children and vulnerable people are present.
Do not use this appliance in series with a thermal control, a program controller, a timer or any other device that swit-
ches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 meter from the applian-
ce.
In the event of a fault unplug the appliance.
Unplug the appliance when not required for long periods.
Although this appliance complies with safety standards, we do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person
in order to avoid a hazard.
Keep the supply cord away from the front of the appliance.
WARNING: In order to avoid overheating, do not cover the appliance. Do not place material or garments on the
appliance, or obstruct the air circulation around the appliance.
The appliance carries a DO NOT COVER warning symbol.
This appliance is not equipped with a device to control the room temperature. Do not use this appliance in small
rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision
is provided.

3—General information
Only use filtered/decalcified water in this appliance.
Unpack the appliance carefully and retain the packaging for possible future use, in the event of moving or returning
the fire to your supplier.
Always ensure that the appliance is sitting on a level surface.
The appliance is a flame effect only.
The appliance is designed to be built into a surround or built into a wall.
PLEASE NOTE: Used in an environment where background noise is very low, it may be possible to hear a sound which
is related to the operation of the flame effect. This is normal and should not be a cause for concern.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air filters must be cleaned once every 2 weeks, particularly in hard
water areas.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the
sump.
The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms to the
latest relevant ISO standard.
Do not drink the water from the sump or from the water tank(s).
4—Installation instructions
This section describes how to install and set up your fire.
Before you start:
Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible future
use.
Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
4.1—Connections required in advance of Installation
Electrical Connection
Please ensure a 240V / 13A power socket is located within 1m of the product. The electrical connection should be
accessible during product installation so that the connection can be made to the product easily.
4.2—Building the product surround/ enclosure
This product can be built into a wall, surround or structure. Please take note of the product dimensions (Fig.1) and
build your wall, surround or structure accordingly. Suitable clearance should be provided to allow the product to be
installed easily.
You are required to leave a minimum of 400mm from the base of the fuel bed to any shelf/enclosure above the pro-
duct (Fig. 2). This will allow enough space above the product to allow the flame effect to form fully and not to be obs-
tructed.
When determining a location for the product, ensure that the unit will not be susceptible to drafts, vents, ceiling fans
and other air currents. Similar to a candle, large movements of air will affect the unit’s ability to create and maintain
the flame effect. If the desired location is susceptible to significant air movement, i.e. air vents, the different installa-
tion options illustrated in Fig 2 can be used.
4.3—Ventilation
This product needs free ventilation from underneath to operate correctly. There are slots on the underside of the
product to allow this free air through the product. The free ventilation helps keep the electronic components cool and
allows the mist to rise and leave the product. Please see Fig 3 & 4 for examples of the required ventilation. Please take
note of the requirement for a ventilation opening on the shelf where the product sits, to allow a clear path for the air
to get to the product.
Kit Glamm 3D Plus 500 Free Ventilation Area: Minimum 210cm2.
Kit Glamm 3D Plus 1000 Free Ventilation Area: Minimum 420cm2.

GlammFire. PAG./15
4.4—Electrical connection
Plug the fire into a 13amp/240 Volt outlet. Be sure to have access to the plug after installation to allow for disconnec-
tion. Ensure that the supply cable exits at the back of the fire at the right or left hand corner to suit your supply socket
location and is not trapped under the fire such that it might cause it to be damaged.
The appliance can be connected to the fixed wiring of the premises through a suitable connection box positioned
adjacent to the appliance. This electrical installation must be carried out by a competent electrician and be in strict
accordance with the current I.E.E regulations for Electrical Equipment in Buildings.
The electrician can remove the supplied plug by the following;
1. Lift off the fuelbed and put switch ‘A’ into the off position (Fig 21).
2. Ensure that the appliance is unplugged.
3. Lift off the access cover by removing the retaining screw (Fig 5).
4. Unscrew and remove the Live, Neutral and Earth wires (Fig 6A)
5. Unscrew the cable clamp (Fig 6B) and remove the supply cord.
6. The electrician can then connect the wire from the appliance to the connection box (by following the steps above in
reverse) ensuring that it incorporates a double pole isolating switch, having a contact separation of at least 3mm.
Brown - Live (L), Blue - Neutral (N) and Green/Yellow - Earth €.
4.5—Installing the product into surround/Enclosure
Once your enclosure has been built to the required dimensions and plumbing and electrical connections have been
installed, follow the steps below to install your product.
Sit the product on the constructed base, ensuring the cable and pipes are accessible and not caught under the pro-
duct.
Ensure the product is at the correct height to suit the installation and ensure it is adequately level. This can be done by
adjusting the adjustable feet with a flat head screwdriver. (Fig 7) The levelness of the product can be verified by chec-
king the on-board spirit level which is located on the metal base towards the back of the fire (Fig 8).
Once the product is at the correct height and is level, centre the product within the opening. If using the LED log fuel
bed (which is wider than the product), this can be done by fitting the fuel bed to the product. The fuel bed will centre
itself within the opening and its guides will centre the product underneath (Fig 9).
With the product in its final position, remove the fuel bed and screw the product to the surround using the four fixing
holes shown in Fig 10.
4.6—Comissioning/initial product start-up
Connecting the Receiver / Tethered Remote
Insert the 3.5mm jack of the Bluetooth receiver into the socket at the back of the appliance (Fig. 11). It is important to
ensure that the jack is pushed fully into the socket. Failure to fully insert the jack will prevent the product from func-
tioning correctly. The receiver has a cable length of 1.4m which will allow you position it anywhere around the pro-
duct. If you prefer to hide it, the receiver can be placed inside the surround/wall. Please ensure that the receiver is not
enclosed in metal, concrete or any other dense material, this will affect the signal from the remote control.
Filling the water tank
Before powering on the product for the first time, ensure that a full water tank has been placed on the product.
Remove the water tank from its location on top of the sump (Fig 12A) and open it by unscrewing the orange cap (Fig
12B). The tank should be filled with filtered/ decalcified water only. When the tank is replaced on top of the sump, it
will take about one minute for the tank to empty into the sump. Allow the sump to fill fully before switching on the
product. Once filling is complete, the tank can be refilled and replaced on top of the sump. This will allow for the maxi-
mum capacity of water to be stored in the product.

Installing the Log Fuel Bed (If Supplied)
The product is supplied with a ‘metal fuel bed’ fitted. If you have chosen to operate your product with a log fuel bed,
remove this metal fuel bed and retain it for future use (Fig. 13). Follow the steps below to install the log fuel bed.
1. Gently lift the LED Log fuel bed out of its packaging. CAUTION: The fuel bed weighs 5kg. Be sure to only lift the fuel
bed by the two centre logs (Fig. 14).
2. Place the fuel bed on top of the appliance, there are 4 plastic guides under the fuel bed to help locate it (Fig.9).
Please note the fuel bed can be placed front to back or back to front on the product.
3. Once the fuel bed is in place, remove the small loose log (Fig 15). This small log is secured with magnets and should
easily lift off the fuel bed.
4. Locate the DC jack under the small log and connect it to the corresponding DC jack located on the product through
the hole in the fuel bed (Fig.16).
5. Each log fuel bed is supplied with a loose non LED log. For single Kit Glamm 3D Plus 500 installations, this can be
placed on top of the fuel bed or stored away with the packaging. For Kit Glamm 3D Plus 1000 or multiple product
installations, the loose log can be placed on the centre join between two fuel beds (Fig 17).
4.7—Multiple product installation (daisy chaining)
Power connections
Both Kit Glamm 3D Plus can be installed side by side to elongate the flame effect. When supplying power to multiple
products, ensure the maximum wattage of the combined products does not exceed the rated capacity of the MCB
(Minature Circuit Breaker) in the circuit.
Multiple product control
Each product can be paired with its own remote or multiple products can be paired a single remote. Please note a
maximum of six individual products (either Kit Glamm 3D Plus 500 or 1000) can be connected to a single Bluetooth
remote control. This will allow for control of all products at once with a single remote control. Additionally, the soft-
ware of the product has been designed in such a way that when multiple products are connected to a main switch,
products can be manually switched off and when switched back on they will operate in the same state as before they
were switched off.
Multiple product installation
Follow steps 1-4 in “Installing the Product into Surround/Enclosure” to fit the first product. It is important that the first
product is orientated so that the side of the product with the slots is left free and not connected to first end of the
installation (Fig 18).
1. When the first product is installed and securely fixed, prepare the second product by unscrewing the joining screws
(Fig 19A) and screwing them into the opposite side of the metalwork (Fig 19B). Please note, these screws should not
be fully tightened and 5-10 mm of thread should be left protruding from the edge of the product;
2. Fit the second product beside the first product, ensuring the protruding screws of the second product engage with
slots of the first product (Fig 20);
3. Ensure the second product is at the correct height to match the first product and ensure it is adequately level. This
can be done by adjusting the adjustable feet with a flat head screwdriver. (Fig 8) The levelness of the product can be
verified by checking the on-board level (Fig 9);
4. Tighten the screws of the second product so that it joins tightly with the first product.
Additional products can be fitted to the second product by following steps 1-4 above.
5—Operanting the product
This section describes how to activate your fire using either the manual controls or remote control.
5.1—Manual controls
The manual controls are located beneath the fuel bed (Fig 21).
Kit Glamm 3D Plus 500
Mains Switch - Controls the electricity supply to the appliance (Fig 21A).
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate.

GlammFire. PAG./17
Button Panel - Controls the functioning of the appliance (Fig 21B).
q • is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by a
single beep and the main LED lights activating. Be careful not to look directly into the LED’s as they can be
very bright. Although the main LED lights operate immediately, a further 45 seconds of warm up time is
required before the flame effect starts;
• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’
for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible
beep when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audi
ble beep when you reach the maximum level.
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum
volume for this is off. You will hear na audible beep when you reach the minimum level.
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound. You will hear
na audible beep when you reached the maximum level.
Kit Glamm 3D Plus 1000
Mains Switch - Controls the electricity supply to the appliance (Fig 21A).
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate.
Button Panel ‘C’ Controls the functioning of the left side of product while Button Panel ’D’ controls the functioning of
the right side of the product. Please note the flame height and fire crackling noise can be controlled independently on
each individual side of the product.
q • is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated
by a single beep and the main LED lights activating. Be careful not to look directly into the LED’s as they
can be very bright. Although the main LED lights operate immediately, a further 45 seconds of warm up
time is required before the flame effect starts.
• is the pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for
details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible
beep when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audi-
ble beep when you reach the maximum level.
•is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum
volume for this is off. You will hear an audible beep when you reach the minimum level.
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound. You will hear
an audible beep when you reach the maximum level.
5.2—Receiver controls
The product can also be controlled using the receiver which is supplied with the product (Fig 12) .
Kit Glamm 3D Plus 500
q • is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can
be adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after
a product restart. The crackling sound can be turned off completely by using the volume control buttons on
the button panel to reduce the volume to its minimum setting. This minimum setting will be remembered
after a product restart.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible
beep when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an
audible beep when you reach the maximum level.

GlammFire. PAG./18
Kit Glamm 3D Plus 1000
q • is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a
product restart. The crackling sound can be turned off completely by using the volume control buttons on the
button panel to reduce the volume to its minimum setting. This minimum setting will be remembered after a
product restart.
• is the reduce flame button. Press the reduce flame button on the second button row to reduce flame button to
reduce the height/intensity of the flame on the left hand side of the product. Press the reduce flame button
on the third button row to reduce the height/intensity of the flame on the right hand side of the product. You
will hear an audible beep when you reach the minimum level.
• is the increase flame button. Press the increase flame button on the second button row to increase the height/
intensity of the flame on the left hand side of the product. Press the increase flame button on the third row
to increase the height/intensity of the flame on the right hand side of the product. You will hear an audible
beep when you reach the maximum level.
5.3—Remote control
The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote
control and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover. With
the product powered off, a functional test can be carried out on the remote control by pushing any button and obser-
ving the blue LED at the top o the remote flashing with each button push.
Pairing the remote control
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1. Press the rocker switch to the on (I) position; a single beep will be heard.
2. Press the q button on the Button Panel; the product will turn on.
3. Press the button on the Button Panel: the LEDs will start to slowly blink on and off.
4. Press the q button on the remote control. the product LEDs will flash quickly three times and the product will
then automatically switch off. The remote control is now paired to the product and can be used to switch it back on.
The operation of the remote control is the same as described in ‘Receiver Controls’. You can pair multiple products
to the one remote control by repeating the pairing operation as above on your subsequent products. Please
note a maximum of six Kit Glamm 3D Plus 500 or 1000 products can be paired to the one remote control.
Pairing the remote control to multiple products
If you are installing multiple Kit Glamm 3D Plus 500 and/or 1000, products you can pair them to a single remote con-
trol. To do this, please install the products as described in the “Installation Instructions”. Ensure that all products are
connected to mains power and have water supplied. If you are pairing CAS1000 and CAS500 products please choose
the 6 button remote control as the master remote control.
1. Pair the first product as described in steps 1-4 above.
2. On your second product, press the rocker switch to the on (I) position; a single beep will be heard.
3. Press the q button on the Button Panel; the product will turn on.
4. Press the button on the Button Panel, the LED’s will start to slowly blink on and off.
5. Press the button on the remote control; the LEDs will flash quickly three times and the product will then auto-
matically switch off. The remote control is now paired to the two products and can be used to switch them on.
6. Repeat the above steps to pair the next product.
7. When all products are paired, test the remote control by pressing the q button. If any of the products fail to
receive a signal from the remote control you can bring that product back in line with the others via the Manual Con-
trols or the receiver controls.

5.4—Getting the desired flame effect
1. Switch the appliance on by pressing the main switch to the on position and pressing the qbutton. The flames will
start after 45seconds.
2. Press the and buttons to adjust the flame to your desired level. Please give the flame generator time to
react to the changes you make.
Once you have made your adjustments to both the flame height and crackling sound, the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch.
The next time you switch on the appliance, it will start up as normal, wait 45 seconds for the flames to start and then
revert to the adjusted settings.
Nozzle inserts
Nozzle inserts have been supplied and fitted to the nozzle opening. These inserts are used to alter the profile of the
flame effect. These inserts can be removed if a different flame profile is preferred. In addition to these inserts, inserts
for blocking the flame in certain areas have also been supplied. To fit these inserts, remove the exisitng inserts that
have been supplied and fitted to the product. Break the blocking inserts into the required length. Snap the inserts into
the nozzle opening in the desired location. See Fig 22 for further details.
5.5—Low water / Refilling the water tanks
When the water tanks have emptied and the water level in the product is getting low, the product will flash its LEDs
twice and beep twice. The product will operate for a further 15 minutes before beeping once and switching into low
water mode. For products being operated with the LED log fuel bed, the fuel bed will remain illuminated while in low
water mode. At this point, the product can either be switched into standby mode using the remote control or Blue-
tooth receiver or the product can be refilled with water. Refilling the product with water will cause the product to
restart automatically.
To refill the tank, remove the fuel bed and remove the water tank from its position on top of the sump. Refill the
water tank using filtered/decalcified water only. The tank can then be replaced on top of the sump. If the product was
not switched into stan-by mode after experiencing low water, the product will restart automatically after 20 seconds
of refilling.
Please note that for a Kit Glamm 3D Plus 1000 product, the side of the product taht is experiencing low water will flash
twice and beep twice. The water tanks on both side of the Kit Glamm 3D Plus 1000 product can be refilled at this
point as it is likely that they should both be empty or near empty.
6—Maintenence
6.1—General tips
Only use filtered/decalcified water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump.
6.2—Cleaning
Warning –Always press Switch ‘A’ to the ‘OFF’ (0) position (Fig 21) and disconnect from the power supply before
cleaning the fire.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:
Sump, Nozzle, Tank cap and seal, Air filter
For general cleaning use a soft clean duster –never use abrasive cleaners.
To remove any accumulation of dust or fluff, the soft brush attachment of a vacuum cleaner should occasionally be
used.

GlammFire. PAG./20
Sump
1. Press Switch ‘A’ to the ‘OFF’ (0) position (Fig 21);
2. Gently lift off the fuel bed and place it aside;
3. Remove the water tank from its position on top of the sump;
4. Disconnect the electrical conector to the transducers, located on the right side of the sump (Fig 23);
5. There are two Orange clips holding down the nozzle on the sump; one on the left and one on the right hand side of
the nozzle. On the left side, pressw in the clip with one hand and with the other lift the nozzle out of the clip. Repeat
this for the right side ( Fig 24). The nozzle can now be lifted so as not to spill any water. Sit the sump in the sink.
6. Gently lift the sump (Fig 26), taking care to keep it level so as not to spill any water. Sit the sump at the sink;
7. Carefully empty the sump into sink taking note that the transducer is held in place by a retaining clip;
8. Put a samll amount of washing up liquid into sump, and using a soft brush, gently clean all surfaces in the sump;
9. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid;
10. Clean the nozzle with a soft brush and flush out thoroughly with water;
11–Reverse the above steps 1—6 to reassemble.
Transducer
The transducer is a consumable item and may need to be replaced through time, depending on its usage. Replace-
ment transducers can be purchased from our your dealer. The transducer is fixed in the sump with a plastic clip. If you
need to replace your transducer:
1. Follow the steps 1-5 in the CLEANING - Sump section under ‘Maintenance’ to gain access to the;
2. Press the clip back and lift the transducer upwards out of its holder;
3. Place the new transducer into the sump, ensuring the its cable does not sit over the cone;
4. Reverse the above steps to reassemble the nozzle and sump.
Air filter
1. Gently lift out the fuel bed and place it aside;
2. Gently slide the air filter upwards out of its plastic holder (Fig.27);
3. Gently rinse with water in the sink and dry with fabric towel.
4. Replace the filter making sure that the coarse black filter is facing outwards.
5. Replace the fuel bed.
6.2—Changing the leak prevention valve pad
A leak prevention valve has been fitted to the appliance as an additional safety measure (Fig 29). In the unlikely event
that a leak occurs inside the product, the valve will prevent water from flowing to the product. When the valve has
been activated, the pad within the valve absorbs water and expands, shutting off the valve. It can be verified that the
valve has been activated if the pad has expanded and the arm of the valve is in its upper positon (Fig 30A). If the valve
has been activated, the pad must be replaced. A spare pad has been supplied with the product, please follow the
steps below to change the pad.
1. In order to gain access to the valve, the nozzle and the sump must be removed first. Follow steps 1-6 above under
“Sump” to remove the sump and nozzle;
2. Verify that the valve has been activated by checking the orientation of the valve arm. If the pad has expanded and
the valve arm is in the upper position (Fig 30A), the valve has been activated;
3. Remove the old expanded pad and dry the area around the valve. Replace the pad with a new pad, while ensuring
the new pad does not come into contact with water.
4. Close the arm of the valve on top of the newly fitted valve (Fig 30B).
5. Replace the sump and nozzle and check that the product is operating by switching it on and ensuring water is flo-
wing into the sump. The product should be carefully inspected for leaks after replacing the valve.
Please note the product is not to be operated without the pad being fitted to the leak prevention valve.
If leaking persists after replacing the valve, contact your dealer or service agent.