Goldmedal Sno-Konette Deluxe 1002 User manual

Sno–Konette
Instruction Manual
Deluxe – Model #1002
Standard – Model #1003
DC Battery – Model #1009
PartNo.22045
RevisedJune 1996
Cincinnati, OH 445241-4807 USA
Model #1002
Model #1003
BACK TO INDEX

SAFETY PRECAUTIONS
NOTE
The information, specifications and illustrations contained in this manual represent
the latest data available at time of publication. Right is reserved to make changes as
required at the discretion of Gold Medal Products Company without notice.
Any alterations to this equipment will void the warranty and
may cause a dangerous situation. NEVER make alterations
to the equipment.
Always wear safety glasses when servicing this equipment.
Machine must be properly grounded to prevent electrical shock
to personnel.
Do NOT immerse the equipment in water.
Always unplug the equipment before cleaning or servicing.
This equipment is designed and sold for commercial use only. This
equipment is not to be used by the consumer in home use. Do not allow
direct contact of this equipment by the public when used in food service
locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all installation instructions before operating the equipment.
Never put your fingers or any object into the shaver body (the goose-
neck) while the motor is running. Serious injury may occur. (Gold
Medal Products does not assume any liability for injury due to careless
handling and/or reckless operation of this equipment) .

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
1
INSTALLATION
MACHINEDESCRIPTION
The Sno-Konette is an automatic shaver with a tremendous capacity. You will find that it keeps
up with any demand; as soon as you put ice into the hopper, it is shaved into fine snow. The
Sno-Konette consists of the gooseneck, which houses the cutter head, the pusher handle, the
motor, and the display case.
ELECTRICALREQUIREMENTS
The Sno-Konette operates on 120 Volt, single phase, 60 cycle AC current. Models are avail-
able in a 12 volt DC version. Be sure that your electrical supply meets this requirement.
ICEREQUIREMENTS
The Sno-Konette can take ice cubes or block ice, if you break the block into pieces approxi-
mately 3 to 4 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large. The design of the
shaving chute automatically draws the ice against the blades. There is no need for manual
effort.
MACHINE OPERATION
The Sno-Konette has seperate switches for the motor and the display lights. The motor toggle
switch is located on the motor body. The switch for the display lights is located inside the case
near the flourescent light.
After unpacking the
Sno-Konette you should locate the pusher handle (packed in a seperate box).
Connect the pusher handle to the shaver body. Plug the power cord into the appropriate electrical
outlet.
Turn on the motor and the display lights. If the bulbs do not light, rotate the flourescent tube to seat it
into the starter. The flourescent bulb is a common 14 Watt tube, available at most retail stores.
TO OPERATE THE SNO-KONETTE
1. Switch the motor on.
2. Wait for the motor to come to full speed (a minute or so).
3. Fill the gooseneck to within an inch of the top with ice cubes or block ice (no larger than 3"
to 4"). The larger the pieces, the better the snow.
4. Push the pusher handle down against the ice in the gooseneck. Apply firm and even
pressure to make the best snow. Practice will allow you to gauge when to stop pressing.
This allows the ice to resettle against the cutterhead. You may find that you need to relieve
the pressure two or three times in a cycle. Over pressing will stall the motor. In this case,
simply relieve the pressure and try again. Too much pressure will result in snow that is
coarse; too little pressure will make the snow mushy.
5. Be aware that under normal operating conditions the motor will become very warm. A
surface temperature of 150º F is normal.
NOTE: Never allow any foreign or metallic objects around the shaver area of the
Sno-Konette .
Blades are often damaged by ice picks and scoops, and debris that may be in the ice.

Sno-Konette
ALLMODELS #1002, #1003 AND #1009
2
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the equipment in water.
Unplug your machine before servicing.

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
3
INSTALLING NEW SHAVER BLADES
Inspect your equipment before replacing the blades. Use a flashlight to examine the blades in
the shaver body. If the blades appear to be nicked or bent, then the blades should be re-
placed. Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2. Remove the cutterhead from the motor shaft by loosening the Allen head set screw
between the motor and the gooseneck. Use the special Allen wrench that was supplied
with your machine.
3. Remove the cutterhead. Pull the cutterhead off of the motor shaft and through the
gooseneck. If the cutterhead is frozen onto the shaft, remove the hold down bolts on
the motor. Pull the motor back, trapping the cutterhead against the inside of the goose
neck, until the cutterhead disengages.
4. After removing the cutterhead, check the motor shaft for burrs and corrosion. Use a
fine tooth file to remove the burrs and corrosion.
5. Remove the blades from the cutterhead. These blades may be resharpened, but it is
far better to replace the old blades with a new set.
6. Position the new blades and insert screws until they are finger tight.
7. Set the blade thickness equal to a penny. (See illustration below.) Make sure that the
height is even across the cutterhead.
8. Tighten the blade screws completely. Check the blades again with a penny to ensure
the blades did not move while tightening the screws.
9. Replace the motor and cutterhead. Mount the motor using the hold down bolts. Insert
the cutterhead through the gooseneck and onto the motor shaft. Press the cutterhead
onto the motor shaft with the pusher handle, then move the cutterhead in another 1/8".
Check that the cutterhead is not rubbing against the back of the gooseneck and the
blades are not touching the pusher handle.
10. Replace the set screw between the gooseneck and the motor.
NOTE:
Replace the shims that were between the motor base and the mounting surface. The
motor shaft must be in alignment with the shaver drive shaft. Misalignment will cause the
motor coupling to wear rapidly.
Set top of blade flush with
height gage, as shown.
Height gage
(use penny)
Shaver Blade
Screw with washer Cutterhead

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
4
PARTS LIST – MODEL #1002
Part No. Description
12003 Top Exterior Frame
12004 Bottom Exterior Frame
12006 Door Assembly
12007 Corner Post
12009 Flourescent Light Tube
12012 Front Glass Strip
12013 Rear Glass Strip
12032 Top Exterior Frame (Front & Rear)
12038 Front Glass
12039 Side Glass
12040 Front Glass Decal
12045 Door Catch
12057 Rear Exterior Frame
12061 Drain Pan Assembly w/ Drain
12063 Protectective Cover, Light
12071 "Do Not Apply Pressure" Label
12072 Cap
22004 "Name & Spec" Plate
22005 Pusher Handle
22009 Hopper Casting
22010 Motor Mount Plate
22012 Drive Motor (120 V)
22013 Motor Switch
22015 Sno-Konette Shave Head
22020 Ice Pick
22021 Pusher Handle Gasket
22023 Molded Recessed Bumper
22024 Shipping Carton
22025 Fluorescent Fixture Lid
22026 Light Fixture Housing Assembly
22028 End Housing
22034 Ice Shaver Drain Hose
22038 Lead-in Cord (15 Amp Plug)
22045 Sno-Konette Parts Manual
22046 "Deluxe Sno-Konette" Decal
22047 Dome
22048 "Deluxe Sno-Konette" Nameplate
22049 Motor Plate
22050 Light Mounting Plate
22051 Lead-in Cord Mounting Bracket

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
5
PARTS LIST – MODEL #1002 (continued)
Part No. Description
22051 Lead-in Cord Mounting Bracket
22052 Dome Mounting Bracket
22053 Window
22054 Pushbutton Switch
22055 Dome Support Bracket
29066 6 Oz. Sno Dipper
39018 6 Oz. Cup Dispenser w/ Bracket
39044 Drain Fitting
39058 Motor Switch Guard
39068 Ice Scoop
41013 Door Knob
41020 Light Tube Holder
41021 Light Tube Holder Starter
41022 Light Ballast
41023 Light Starter
41057 Light Tube
47010 "Safe Operating Instructions" Label
47132 Vinyl Glass Channel (per foot)
47155 3/4 Inch High Rubber Feet
47201 Motor and Light On/Off Switch
47509 Wall Mount Bracket
49132 Grip Nut (5/16-18)
74119 "Warning Disconnect Power" Label
74127 Set Screw (5/16-18 x 3/8 Long)
75220 Hose Clamp w/ Screw
76026 Strain Relief
76097 "Unplug to Clean" Label
76135 Power Cord Tag
76210 Stop 110 Volt Unit Tag
77521 Slot Head Hex Screw (#8-32 x 3/4 Long)
82004 Light Tube Protective Cover
86556 18-2 Wire (Type SJTO)

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
6
PARTS LIST – MODEL #1003
Part No. Description
12003 Top Exterior Frame
12004 Bottom Exterior Frame
12006 Door Assembly
12007 Corner Post
12009 Flourescent Light Tube
12012 Front Glass Strip
12013 Rear Glass Strip
12032 Top Exterior Frame (Front & Rear)
12038 Front Glass
12039 Side Glass
12040 Front Glass Decal
12045 Door Catch
12057 Rear Exterior Frame
12061 Drain Pan Assembly w/ Drain
12063 Protectective Cover, Light
12071 "Do Not Apply Pressure" Label
12072 Cap
22004 "Name & Spec" Plate
22005 Pusher Handle
22009 Hopper Casting
22010 Motor Mount Plate
22012 Drive Motor (120 V)
22013 Motor Switch
22015 Sno-Konette Shave Head
22020 Ice Pick
22021 Pusher Handle Gasket
22023 Molded Recessed Bumper
22024 Shipping Carton
22025 Fluorescent Fixture Lid
22026 Light Fixture Housing Assembly
22028 End Housing
22034 Ice Shaver Drain Hose
22038 Lead-in Cord (15 Amp Plug)
22045 Sno-Konette Parts Manual
22047 Dome
29066 6 Oz. Sno Dipper
39018 6 Oz. Cup Dispenser w/ Bracket
39044 Drain Fitting
39068 Ice Scoop
41013 Door Knob

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
7
PARTS LIST – MODEL #1003 (continued)
Part No. Description
41020 Light Tube Holder
41021 Light Tube Holder Starter
41022 Light Ballast
41023 Light Starter
47010 "Safe Operating Instructions" Label
47132 Vinyl Glass Channel (per foot)
47155 3/4 Inch High Rubber Feet
47201 Motor and Light Switch
47509 Wall Mount Bracket
49132 Grip Nut (5/16-18)
74119 "Warning Disconnect Power" Label
74127 Set Screw (5/16-18 x 3/8 Long)
75220 Hose Clamp w/ Screw
76026 Strain Relief
76097 "Unplug to Clean" Label
76135 Power Cord Tag
76210 Stop 110 Volt Unit Tag
77521 Slot Head Hex Screw (#8-32 x 3/4 Long)
82004 Light Tube Protective Cover
86556 18-2 Wire (Type SJTO)

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
8
PARTS LIST – MODEL #1009
Part No. Description
12003 Top Exterior Frame
12004 Bottom Exterior Frame
12006 Door Assembly
12007 Corner Post
12009 Flourescent Light Tube
12012 Front Glass Strip
12013 Rear Glass Strip
12032 Top Exterior Frame (Front & Rear)
12038 Front Glass
12039 Side Glass
12040 Front Glass Decal
12045 Door Catch
12057 Rear Exterior Frame
12061 Drain Pan Assembly w/ Drain
12063 Protectective Cover, Light
12071 "Do Not Apply Pressure" Label
12072 Cap
22004 "Name & Spec" Plate
22005 Pusher Handle
22009 Hopper Casting
22010 Motor Mount Plate
22013 Motor Switch
22015 Sno-Konette Shave Head
22020 Ice Pick
22021 Pusher Handle Gasket
22023 Molded Recessed Bumper
22024 Shipping Carton
22025 Fluorescent Fixture Lid
22026 Light Fixture Housing Assembly
22028 End Housing
22034 Ice Shaver Drain Hose
22035 Switch Box Cover
22036 Switch Box
22037 Circuit Breaker (40 Amp)
22041 Motor (12 V DC)
22042 Sno-Konette Shaver Head Battery
22043 Power Supply Cord Assembly
22045 Sno-Konette Parts Manual
22047 Dome
22049 Switch Box

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
9
PARTS LIST – MODEL #1009 (continued)
Part No. Description
29066 6 Oz. Sno Dipper
39018 6 Oz. Cup Dispenser w/ Bracket
39044 Drain Fitting
39068 Ice Scoop
41013 Door Knob
41020 Light Tube Holder
41021 Light Tube Holder Starter
41022 Light Ballast
41023 Light Starter
42018 Switch
47010 "Safe Operating Instructions" Label
47132 Vinyl Glass Channel (per foot)
47155 3/4 Inch High Rubber Feet
47201 Motor and Light Switch
47509 Wall Mount Bracket
49132 Grip Nut (5/16-18)
74119 "Warning Disconnect Power" Label
74127 Set Screw (5/16-18 x 3/8 Long)
75220 Hose Clamp w/ Screw
76026 Strain Relief
76097 "Unplug to Clean" Label
76135 Power Cord Tag
76210 Stop 110 Volt Unit Tag
77521 Slot Head Hex Screw (#8-32 x 3/4 Long)
82004 Light Tube Protective Cover
86556 18-2 Wire (Type SJTO)

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
10
ELECTRICAL SCHEMATIC – MODEL #1002

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
11
ELECTRICAL SCHEMATIC – MODEL #1003

Sno-Konette
ALL MODELS #1002, #1003 AND #1009
12
ELECTRICAL SCHEMATIC – MODEL #1009

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, volt-
age, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
ORIMPLIED,ANDOFALLOTHEROBLIGATIONSORLIABILITIESONOUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP-
TION ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASERFIRSTCALLSGOLDMEDALPRODUCTSCOMPANY AT1-800-
428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP-
MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERN-
ING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, OH 45241-4807 USA