Goldmedal Antique Citation User manual

© 2023 Gold Medal Products Co.
Part No. 47699
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Antique Citation
Model Series: 2119
Model 2119 (100)
Model 2119NL

Antique Citation Model Series: 2119
Page 2
gmpopcorn.com
Table of Contents
SAFETY PRECAUTIONS ...................................................................................................................................3
INSTALLATION INSTRUCTIONS ...................................................................................................................5
Inspection of Shipment .......................................................................................................................................5
Manual.......................................................................................................................................................................5
Model Description.................................................................................................................................................5
Items Included with this Unit ...........................................................................................................................5
Setup...........................................................................................................................................................................6
Electrical Requirements .....................................................................................................................................8
Before You Plug In Machine ..............................................................................................................................8
OPERATING INSTRUCTIONS .........................................................................................................................9
Controls and Their Functions...........................................................................................................................9
Popping Corn Instructions.................................................................................................................... 10
Care and Cleaning .................................................................................................................................... 11
Daily Kettle Cleaning Instructions ...............................................................................................................11
Daily Unit Cleaning Instructions...................................................................................................................12
Sanitizing the Oil System (Tubing and Pump) ........................................................................................12
Weekly Filter Cleaning Instructions ...........................................................................................................13
Troubleshooting....................................................................................................................................... 13
Agitator Set Collar Adjustment............................................................................................................15
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY ............16
MAINTENANCE INSTRUCTIONS ................................................................................................................ 16
ORDERING SPARE PARTS............................................................................................................................17
Replacing Broken Glass....................................................................................................................................17
16 oz. Kettle Assembly (55166) –Agitator Assembly View.................................................................18
16 oz. Kettle Assembly (55166) –Kettle Bottom Assembly.................................................................19
Cabinet Exterior –Front View.......................................................................................................................21
Cabinet Exterior –Rear View.........................................................................................................................22
Door Hardware Kits –Individual Component Breakdown................................................................23
Cabinet Interior –Hanger Assembly/Controls View............................................................................24
Cabinet Interior –Corn Pan View ................................................................................................................25
Warmer Blower Assembly..............................................................................................................................26
Dome Interior –Electrical Components –Parts Breakdown ............................................................27
Safety Labels.........................................................................................................................................................29
Accessories ...........................................................................................................................................................29
Wiring Diagram ........................................................................................................................................30
WARRANTY...................................................................................................................................................... 32

Antique Citation Model Series: 2119
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Antique Citation Model Series: 2119
Page 4
gmpopcorn.com
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

Antique Citation Model Series: 2119
Page 5
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
2119 (100): Antique Citation 16 oz. Popcorn Popper, gold color cabinet with 15 vintage
LED display lights. Unit has a forced air popcorn crisping system.
2119NL: Antique Citation 16 oz. Popcorn Popper, gold color cabinet; no display lights.
Unit has a forced air popcorn crisping system.
Items Included with this Unit
20 cc Flavacol
Measure
(PN 47680)
16 oz. Corn
Measure
(PN 68050)
Aluminum
Scoop
(PN 2071)
Registration
Warranty Card
6 oz. Oil Measure
(PN 49049)
Power Supply
Receptacle
(PN 47211)
Receptacle Cover
(PN 47377)
Instruction
Manual
Display Light Bulbs (x15)
(PN 105041, one bulb)
Clear Lens Body and
Lens Cap (x15)
Only included in units
with Display Lights;
select Models only.

Antique Citation Model Series: 2119
Page 6
gmpopcorn.com
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place the unit on a sturdy, level base.
3. The Popper blower vents out the top of unit, allow adequate clearance for airflow.
Sufficient clearance is also needed on side of the popper with power supply cord
routed from the base.
4. The door knobs are shipped facing the inside of the machine. Re-adjust knobs to face
the outside of the machine.
5. Install the Display Lights (if equipped, select Models only): There are 15 Display
Lights on the unit. Each light has an LED bulb, clear lens body, and a clear lens cap.
Unpack the display light parts and assemble as shown below.
6. Make sure kettle lead-in cord is securely plugged into unit and twisted to lock into the
kettle receptacle (reference image below).
Make sure Kettle Lead is
plugged in completely and
twisted to lock into Kettle
Receptacle.
1
2
To Install Display Lights:
Model 2119 (100) shown, Model 2119NL not equipped with Display Lights.
Image shown for general
reference only.
d) Screw Clear Lens Cap
onto Lens Body.
b) Thread the Clear Lens Body onto socket.
c) Screw LED Bulb into socket.
a) Make sure socket is securely fastened in place.
To Replace an LED Bulb:
Unscrew Lens Cap, then
remove old bulb.

Antique Citation Model Series: 2119
Page 7
gmpopcorn.com
7. The main power cord is located out the cabinet base (reference image below), a
secondary, special power cord is provided for powering the oil dispense unit. These
units are equipped with an aluminum oil line for connecting the oil dispense unit.
(Reference Instruction Manual for the oil dispense unit to connect it to the popper.)
8. After setup, unit should be cleaned prior to use (see Care and Cleaning section).
Power Cord
Power Cord Socket (for 6 Prong
Plug on Oil Dispense Unit)
Aluminum Oil Line
Extends out bottom
corner of popper, use to
connect to oil line on the
oil dispense unit.
View under Corn Pan
Image shown for general reference only.

Antique Citation Model Series: 2119
Page 8
gmpopcorn.com
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
120 V~, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power
supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Antique Citation Model Series: 2119
Page 9
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
LIGHTS SWITCH
ON/OFF lighted rocker switch - supplies power to the exterior display lights (if equipped)
and interior cabinet light. The green switch light ON indicates there is power to the lights.
KETTLE HEAT SWITCH
ON/OFF lighted rocker switch - supplies power to the heating elements in the popping
kettle. The green switch light ON indicates there is power to the kettle heating element.
KETTLE MOTOR SWITCH
ON/OFF lighted rocker switch - supplies power to the kettle agitator motor and exhaust
blower. The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped
or un-popped) in the kettle. The green switch light ON indicates there is power to the
agitator motor and exhaust blower.
WARMER SWITCH
ON/OFF lighted rocker switch - supplies power to the crisper/blower in the corn staging
area, keeps popcorn fresh and crisp.
OIL SYSTEM MASTER SWITCH
ON/OFF lighted rocker switch - supplies power to the oil pump (either the Bag-in-a-Box
or Bucket Pump model). Reference the Instruction Manual for the oil dispense unit.
Bag-in-a-Box Model: Oil System Master Switch ON, provides power to the oil dispense
unit, activates the cabinet warmer/blower, and the heated line kit (if equipped).
Note: Coconut oil will congeal at temperatures below approximately 76°F (24°C). For
machines used daily, leave the Oil System Master Switch on at all times and keep
the cabinet doors closed to prevent the oil from becoming solid. If the machine has
not been used for several days, turn the Oil System Master Switch ON the night
before it is expected to be used.
Bucket Pump Model: Oil System Master Switch ON, activates the small heating element
on the bucket pump to keep the coconut oil liquid.
OIL DISPENSE PUSH BUTTON (PB) SWITCH & OIL LIGHT
Red Push Button Switch - dispenses a predetermined amount of oil into the kettle when
pressed. The Oil System Master Switch must be ON for the Oil Dispense PB Switch to
activate (reference the Instruction Manual for the oil dispense unit). The Oil Light on the
popper will light continuously when oil pump is dispensing.
CIRCUIT BREAKER
The Circuit Breaker(s), located in cabinet interior on the ceiling of the popper, protects
the popper unit from overload condition. If unit is plugged in, but the kettle motor or oil
system does not come on when activated, then the circuit breaker(s) may be tripped.
(Reference the Troubleshooting section of this manual).

Antique Citation Model Series: 2119
Page 10
gmpopcorn.com
Popping Corn Instructions
The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored
coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in
the kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Popping Salted (Standard) Popcorn
Raw Popcorn Charge:
Use corn measure provided (ex: for 6 oz. Kettle, use 6 oz. corn)
Recommended Oil Volume:
Oil volume is approx. 30% of corn amount (ex: for 6 oz. corn, use 2 oz. oil)
Flavacol (Salt) Amount:
Use small Flavacol scoop provided
Premeasure all ingredients (adjust as needed for desired taste), or for best results use Mega-Pop®
premeasured popcorn and oil pouch made for your kettle size.
1. Turn all switches ON.
2. To determine when kettle is ready to pop corn (about 4 minutes), test pop three
kernels of corn in one ounce (30 ml) of popping oil. When kernels pop, kettle is ready.
3. Lift kettle lid, pour in popcorn and Flavacol, then add oil (if equipped with oil dispense
unit, press the “Red” Oil Dispense PB Switch to add oil); close lid.
4. When corn has finished popping, gently dump the popcorn.
Popping Tip: On final batch, turn Kettle Heat Switch OFF just as lids are forced open
by the popping corn (kettle has plenty of heat to finish popping). This helps
eliminate smoke/odor from any oil residue remaining in kettle.
5. When finished popping, turn KETTLE HEAT and KETTLE MOTOR switches OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!
Oil Dispense
Indicator Light
Oil Dispense
PB Switch
Oil System
Master Switch
Lights Switch
Kettle Motor
Switch
Warmer
Switch
Kettle Heat
Switch

Antique Citation Model Series: 2119
Page 11
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet or steam
cleaner. Always unplug the equipment before cleaning or servicing. 025_051321
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
028_082715
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners).
For surfaces needing further cleaning or degreasing, Watchdog Stainless Cleaner (Item No. 2088)
or Watchdog Concession Equipment Degreaser (Item No. 2580) is available for use accordingly.
For any cleaning products used, follow the manufacturer’s instructions on the product. DO NOT
use oven cleaners or abrasive materials as they will damage parts of machine.
Note: It is extremely important to follow all cleaning procedures, otherwise parts
damage and equipment failure will result. The warranty does not cover parts that
are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
1. Turn the power switch OFF and unplug the unit.
CAUTION: A hot kettle will cause burns if you touch it. Allow kettle to cool at least 1
hour before attempting to clean. DO NOT use ice or water to cool down a hot
kettle! Severe kettle damage will result and steam burns may occur!
2. When cool, wipe outside of kettle clean using a clean, soft cloth and Gold Medal
Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive
materials as they will damage the kettle.
3. Mix 2 tablespoons (29.6 ml) of Gold Medal’s Heat’n Kleen (Item No. 2095) in 1 gallon
(3.8 L) of water.
4. Only pour enough of the Heat’n Kleen pre-mixed solution into the kettle to fill it 1/2 inch
(12.7 mm) deep (it is not necessary to use the entire gallon at once).
5. Plug in the unit.
6. Turn kettle heat ON. When solution starts to boil, turn kettle heat OFF.
7. Allow kettle to cool at least 1 hour, then unplug unit.
8. Dump solution into a bucket, do not spill any in the interior of machine.
9. Rinse kettle interior with clean water and a clean cloth.

Antique Citation Model Series: 2119
Page 12
gmpopcorn.com
10. Dump any water remaining into a bucket (do not spill any in the interior of machine),
then wipe the kettle interior clean with a clean dry cloth.
For an extra dirty kettle, the process may be repeated; or, after turning kettle heat OFF,
allow solution to sit in kettle overnight. The next morning, finish the cleaning steps.
11. With unit OFF and unplugged, use a clean SLIGHTLY damp cloth (wring ANY EXCESS
water from cloth before use) and wipe the kettle lead cord clean. DO NOT get moisture
into the kettle lead-in cord, severe damage will result.
12. After kettle cleaning, check to be sure the crossbar fasteners are securely tightened.
Daily Unit Cleaning Instructions
1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.
2. Remove any remaining popcorn.
3. Remove all pans/accessories and take them to the sink to clean with soap and water,
then rinse and dry.
4. Clean under corn pan to remove all popcorn bits and seeds with a vacuum as needed,
then wipe the area with a clean dry cloth to remove any grease.
5. Wipe clean the area above the corn pan and exterior surfaces using a clean, SLIGHTLY
damp cloth to remove any grease from the glass and cabinet (cloth may be SLIGHTLY
dampened with soap and water, then wipe again with clean water to remove any
remaining cleaner).
6. Clean glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No.
2588) is recommended.
Ammonia cleaners will damage plastic doors/panels. Only use a non-ammonia cleaner,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
7. Reinstall the clean, dry pans/accessories.
8. Check the kettle lead cord, make sure it is fully plugged into the kettle receptacle and
the plug (or plug collar) is fully twisted to lock it into place.
Sanitizing the Oil System (Tubing and Pump)
Reference the Oil Dispense Unit manual for oil system cleaning instructions.

Antique Citation Model Series: 2119
Page 13
gmpopcorn.com
Weekly Filter Cleaning Instructions
The popcorn machine is equipped with an efficient and durable filtration system. The filter
should be cleaned every week to maintain maximum efficiency.
Troubleshooting
Issue
Possible Cause
Solution
No Power to the Unit
A. No Power to the Unit
A. Make sure the unit’s power cord is plugged in.
B. Mini Circuit Breaker(s) on
popper tripped
(if equipped)
B. Mini Circuit Breaker(s) supplies power to all
unit features. If equipped, Mini Circuit
Breaker(s), will be located on the control
panel or ceiling of the popper. If breaker(s) is
reset, then trips again, the unit must be
inspected/repaired before going any further.
Kettle Does Not Heat
A. Power to the Kettle (for
units with a removable
kettle)
A. Make sure kettle lead-in cord is plugged in
completely and twisted to lock it into the
kettle receptacle. (Kettle leads which have a
locking ring, ensure locking ring is fully
screwed onto kettle receptacle.)
B. Kettle Heat Switch
B. Have a qualified service person check the
voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.
C. Heating Element
C. Heating element in the kettle may be burned
out. Check with a qualified service person for
inspection/repair.
Steps to Clean Filter
1. Turn unit OFF and allow it to cool before
removing filter. Filter is located inside the
popcorn machine, above the popping kettle.
2. Remove filter by sliding it out of the filter
retaining angles.
3. Clean filter in warm soapy water, then rinse
and allow to dry overnight. Reinstall filter
to its original position (as shown above).
Filter

Antique Citation Model Series: 2119
Page 14
gmpopcorn.com
Issue
Possible Cause
Solution
Oil Pump Does Not Deliver
Oil to Kettle (for units
equipped with oil)
A. Mini Circuit Breaker(s) on
popper tripped (if
equipped)
A. Check the Mini Circuit Breaker(s); if reset,
then trips again, the unit must be inspected/
repaired by qualified service personnel.
B. Oil Dispense Unit
B. For additional possible causes/solutions,
reference the Troubleshooting section of the
Oil Dispense Unit Manual.
Long Popping Cycles
(Longer than 4 minutes for
Salt Popcorn; longer than 6
minutes for Sweet Popcorn)
A. Heating Element
A. For units with multiple elements in the kettle,
one of the heating elements in the kettle may
be burned out. This would result in the kettle
never reaching the proper operating
temperature. Check with a qualified service
person for inspection/repair.
B. Low Voltage
B. If the machine is operated on low voltage, this
could cause the kettle not to reach the proper
operating temperature. Check with a qualified
electrician.
C. Inadequate Supply Lines
C. Inadequately sized electrical supply lines or
use of extension cord, in addition to being a
fire hazard, would also prevent the kettle from
reaching the proper operating temperature.
Check with a qualified electrician.
D. Inferior Corn
D. Inferior quality corn would result in longer
popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even then,
if you let your corn pick up moisture or dry
out, your popping cycles will be slow.
Kettle Agitator Shaft not
Rotating
If the kettle agitator shaft is
not rotating, DO NOT pop
corn.
A. Mini Circuit Breaker(s) on
popper tripped
(if equipped)
A. Check the Mini Circuit Breaker(s); if reset,
then trips again, the unit must be inspected/
repaired by qualified service personnel.
B. Kettle Motor Switch
B. Make sure the Kettle Motor Switch is ON. If the
switch is ON, and the shaft is not rotating, the
switch or motor may be faulty, contact
qualified service personnel for
inspection/repair.
C. Kettle Agitator Shaft/Stir
Blade not rotating. (Unit
must be OFF, unplugged
and cool prior to
checking or adjusting
the agitator assembly.)
C. Kettles with a FIXED Stir Rod –check the
clearance between the shaft with welded stir
blade and the kettle bottom; it should be a
minimum of 1/32” (1 mm) (thickness of a dime).
To make shaft adjustments, reference the
Agitator Set Collar Adjustment section.
Poor Crisper/Blower
Performance (Blower is
working, but air not
circulating properly.)
A. Popcorn chaff build up
A. Follow proper cleaning procedures to keep
area under corn pan free of debris, reference
Cleaning and Care section.

Antique Citation Model Series: 2119
Page 15
gmpopcorn.com
Agitator Set Collar Adjustment
The following instructions describe how to properly adjust set collars on an agitator assembly
with a fixed stir rod.
Steps to Adjust Set Collars on Agitator with a Fixed Stir Rod
Agitator assembly is adjusted while fastened to the kettle (image shown for general reference only).
1. Turn machine OFF, unplug unit, and allow it to cool completely before attempting to adjust
the agitator height.
2. Loosen the set screw in the set collar above the crossbar and below the crossbar.
3. Place a 1/32” (1 mm) gauge (thickness of a dime) under the base of the agitator shaft to adjust
clearance between the kettle cook surface and the shaft; reference image shown. Once
adjusted, re-tighten the set screw in the set collar above the crossbar to secure shaft in place.
4. Adjust clearance between the bottom of the
crossbar and the lower set collar to 1/32”
(1 mm) (thickness of a dime); reference
image shown. Once adjusted, re-tighten set
screw to secure in place.
5. To check for proper adjustment, make sure
the stir rod is parallel to the kettle cook
surface (it should be close - but not
touching).
6. Spin the agitator shaft by hand to ensure it
spins freely and is not dragging the bottom
of the kettle.
Agitator shown for general
image reference only (lids not
shown for clarity).
Step 3: Adjust clearance to
1/32” (1 mm)
(thickness of a dime)
Kettle Cook
Surface
Crossbar
Set Collar w/Set Screw
above Crossbar
Lower Set Collar
Agitator Shaft
Step 4: Adjust clearance to 1/32” (1 mm)
(thickness of a dime)
Stir Rod (welded to shaft)

Antique Citation Model Series: 2119
Page 16
gmpopcorn.com
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Antique Citation Model Series: 2119
Page 17
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to Parts Department, Gold Medal Products Co., 10700
Medallion Drive, Cincinnati, Ohio 45241-4807
or place orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: [email protected]
Web Page: gmpopcorn.com
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop, always purchase tempered glass.
GLASS DIMENSIONS (Height x Width x Thickness)
Front and Side Glass: 28 1/8” x 23 3/16” x 1/8”
1. Turn machine OFF, unplug unit and allow it to cool before attempting to replace glass.
2. Carefully remove all loose pieces of broken glass.
3. Lift out the corn pan (bottom pan).
4. Locate the Glass Retainer Strips on each corner post holding in the glass panel, and
remove the screws to unfasten the retainers.
5. Carefully remove the rest of the broken glass.
6. Remove all rigid glass channels from around the glass to be replaced, set channels
aside for reuse.
7. Apply decals (if desired) to new glass panel.
8. Slide rigid glass channels over the exposed sides and bottom of new glass panel.
9. Fasten new glass panel in machine with existing glass strips and screws.
10. Reinstall corn pan (bottom pan).

Antique Citation Model Series: 2119
Page 18
gmpopcorn.com
16 oz. Kettle Assembly (55166) –Agitator Assembly View
Item
Part Description
Part Number
55166
1
THUMB SCREW 1/4-20 X 3/4
38379
2
10-32 X 1/2 PH FL HD MS
40717
3
THREADED BLOCK
61167
4
LID & AGITATOR ASSEMBLY (Complete Assy.)
41066
5
CROSSBAR ASSEMBLY
41086
6
FRONT LID
41123
7
REAR LID
41120
8
AGITATOR BEARING HUB
43434
9
NEEDLE BEARING
47106
10*
SPUR GEAR KIT (Includes 2 gears with set
screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)
47059K
11
10-32 X 3/16 SET SCREW
41742
12
AGITATOR SHAFT ASSEMBLY
41093
13
½ ID X 7/8 OD SET COLLAR
47326
14
¼-20 X 3/16 SET SCREW
47751
15
OIL TUBE W/ FUNNEL
41239
Complete Kettle Assembly
See Kettle Bottom
Assy. section for
parts breakdown
(includes Handle
Assembly and
Kettle Lead).
55166O verall Kettle
55166E Ag.Ass y.
55199E Exp. Views
1
2
3
Complete Agitator Assembly
(Includes Lids)
4
Complete Agitator Assy.
(Includes Lids)
*See Parts
List note.
8
9
10*
11
15
13, 14
12
5
6
7

Antique Citation Model Series: 2119
Page 19
gmpopcorn.com
16 oz. Kettle Assembly (55166) –Kettle Bottom Assembly
Element View
2
3
1
4
8
7
6
5
9
Use high temp
red Loctite on
the three flange
nuts.
10
11
12
Top Lock Nut - Fastens each
thermostat and ground.
Install Lock Nut with triangle
in UP position (as shown).
ONE TIME USE ONLY,
REPLACE NUT if removed.
55199Kettle E lement
55199EXKettle Bo ttom Assy.
55199E exp.vi ews
13
14
15
16
17
Kettle Bottom Assembly View
25, 26
24
22
23
21
20
19
18*
*Dump Handle
Assembly
(includes Knob)
Kettle Conduit
Label (not shown)

Antique Citation Model Series: 2119
Page 20
gmpopcorn.com
16 oz. Kettle Assembly (55166) –Kettle Bottom Assy. –Parts List
Item
Part Description
Part Number
55166
16OZ KETTLE BOTTOM ASSY (Complete Assy.)
55200
1
TRANSFER PLATE ASSY (beneath heat element)
67944
2
KETTLE GASKET
41598
3
KETTLE WELDMENT
67892
4
8-32 SERRATED FLANGE NUT
61151
5
¼ - 20 SERRATED LOCK NUT
46311
6
ELEMENT CLAMP (6 required)
67894
7
1550 TUBULAR HEAT ELEMENT
67014
8
LIMIT THERMOSTAT SHIELD
67959
9
8-32 TOP LOCK NUT (always replace if removed)
67943
10
510F THERMOSTAT (includes two 6-32 screws)
77107
11
THERMOSTAT SHUNT BAR
47193
12
550 F THERMOSTAT (includes two 6-32 screws)
77108
13
KETTLE SHELL ASSEMBLY (has Pivot Pins
attached)
41081
14
KETTLE LEAD ASSEMBLY
47361N
15
8-32 x 3/8 SLT HWHW M/S (fastens Nameplate
to Jct. Box, and fastens Jct. Box to Kettle)
42044
16
JUNCTION BOX
47393
17
KETTLE CONDUIT LABEL
82840
18
DUMP HANDLE ASSEMBLY (assembly includes
Handle, Knob, 2 SQ HD Screws, and Key)
47102
19
DUMP HANDLE KNOB
47110
20
DUMP HANDLE
47707
21
3 1/8 X ½ WOODRUFF KEY
41730
22
5/16 –18 X ½ SQ HD SCREW
47725
23
5/16 –18 X 3/8 SQ HD SCREW (holds key)
47662
24
PIVOT PIN
41426
25
1/4-20 ACORN NUT
42229
26
1/4-20 X 3/8 BUTTON HEAD
12492