Goldmedal Astro 2002 User manual

© 2022 Gold Medal Products Co.
Part No. 61987
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Astro Staging Cabinet
Model No. 2002, 2002EX

Astro Staging Cabinet Model No. 2002, 2002EX
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Astro Staging Cabinet Model No. 2002, 2002EX
Page 3
gmpopcorn.com
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
DO NOT install equipment in an area where a water jet is used.
Unit to be installed in locations where ambient temperatures are between a minimum of
5°C (41°F) and a maximum of 55°C (131°F).
Unit to be installed in locations where it can be overseen by trained personnel.
Install unit on a level surface.
Unit is a popcorn staging cabinet.
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

Astro Staging Cabinet Model No. 2002, 2002EX
Page 4
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
The 2002 Series is a popcorn staging cabinet. Unit not for the storage or display of time /
temperature control for safety foods.
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place unit on a sturdy, level base for use.
3. For NSF compliance, set unit flush with counter and silicone caulk the 4 sides where
frame meets counter top (see illustration below).
4. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of this
manual).
Bottom frame of
Warmer Unit
Silicone caulk 4 sides where frame meets counter top.
If equipped with an Old Maid Pan, use minimal amount of caulk
under pan opening to avoid interference with the Old Mail Pan.

Astro Staging Cabinet Model No. 2002, 2002EX
Page 5
gmpopcorn.com
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
2002: 120 V~, 60 Hz
2002EX: 220-230 V~, 50/60 Hz
Potential Electrical Variations: 220 V~, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Astro Staging Cabinet Model No. 2002, 2002EX
Page 6
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
LIGHT SWITCH
Two position, ON-OFF lighted rocker switch, provides power to the dome and cabinet lighting.
The green switch light ON indicates there is power to the lighting
LEFT-RIGHT HEATER SWITCHES
Two position, ON-OFF lighted rocker switch, provides power to the heater for the left or the right
hand side of the cabinet.
Operating Instructions
Follow the instructions below to operate the Staging Cabinet:
1. Turn the Light Switch ON to light up the cabinet interior and the dome sign.
2. Turn the Heater Switches ON for approximately 30 minutes prior to use for optimal
pre-warming of cabinet.
3. Place product on the shelves of the cabinet. For best results, allow adequate space
around product for air to circulate.
Light Switch
Left Heater
Switch
Right Heater
Switch

Astro Staging Cabinet Model No. 2002, 2002EX
Page 7
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet or steam
cleaner. Always unplug the equipment before cleaning or servicing. 025_051321
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Follow the directions below to clean and sanitize the unit each day after use.
1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Make sure to clean all of the pans (racks) in order to sanitize them before each use.
3. Remove bottom cabinet pans and clean out any stray debris.
4. The vertical air ducts, mounted on the inside of the cabinet, disassemble without tools
for easy cleaning.
5. Clean unit with a soft cloth, dampened with soap and hot water.
6. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
7. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item
No. 2588) is recommended.
Ammonia cleaners will damage the plastic panels. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Astro Staging Cabinet Model No. 2002, 2002EX
Page 8
gmpopcorn.com
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Astro Staging Cabinet Model No. 2002, 2002EX
Page 9
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: [email protected]
Web Page: gmpopcorn.com

Astro Staging Cabinet Model No. 2002, 2002EX
Page 10
gmpopcorn.com
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop and always purchase tempered glass.
1. Remove all loose pieces of glass.
2. Remove all rigid glass channels from around the glass to be replaced. Set it aside as it
must be reused.
3. Carefully remove the rest of the broken glass.
4. Apply decals (if desired) to the new glass panel.
5. Slide rigid glass channels over the exposed sides and bottom of new glass panel.
6. Fasten new glass panel in machine with the existing glass strips. (On some units, the
front and side glass slide under top and is then lowered into the bottom channel.)
GLASS DIMENSIONS
Front/Side Glass: 32 3/16” X 23 1/16” X 1/8 (3 pieces per unit)

Astro Staging Cabinet Model No. 2002, 2002EX
Page 11
gmpopcorn.com
Cabinet Assembly –Parts Breakdown
See Dome Assembly section
for parts breakdown.
1, 2
18
16
17
3
4, 5
6
21, 22
23
See Door
Hardware
Kit section.
14, 15
24
19, 20
28
27
32
31*
11
12, 13
25
26
9
For Glass Panels, see
Replacing Glass section.
10
7
General image shown for parts reference only.
*CAUTION: If supply cord is damaged,
it must be replaced by Gold Medal
Products Co., its service agent, or
similarly qualified persons in order
to avoid a hazard.
29, 30
8

Astro Staging Cabinet Model No. 2002, 2002EX
Page 12
gmpopcorn.com
Cabinet Assembly –Parts List
Item
Part Description
Part No.
2002
2002EX
1
BLOWER
40254
40299
2
INTAKE COVER
40184
40184
3
BLOWER BRACKET
40145
40145
4
NOZZLE HEATER, 120V 850W
40153
40280
5
ALUMINUM TUBE
47499
47499
6
EXHAUST BOX WELDED
61992
61992
7
HIGH LIMIT, THERMOSTAT
79058
79058
8
TERMINAL BLOCK, 8 POS
47208
47208
9
GLASS CHAN 31 27/32 (for sides of front and
side glass panels)
41858
41858
10
GLASS CHAN 22 7/8 (for top and bottom of glass
panels)
47694
47694
11
DUCT COVER LG
40293
40293
12
DUCT PANEL LG
40292
40292
13
DUCT BRACKET
40177
40177
14
MAGNETIC CATCH BRACKET
41340
41340
15
MAGNETIC CATCH
47561
47561
16
LIGHT SHIELD CONICAL
49480
49584
17
LAMP HOLDER
47047
47047
18
REFLECTOR FLOOD (bulb)
41671
41979EX
19
SHELF SUPPORT LH 1617/TS
16056
16056
20
SHELF SUPPORT RH 1617/TS
16057
16057
21
ROCKER SW 3 HOLE (switch box)
17473
17473
22
ROCKER SWITCH LABEL 3 HL
61986
61986
23
SWITCH, LIGHTED ROCKER GR
42798
42798
24
WIRE SHELF 28 X 28 WMR
61999
61999
25
DOOR 11.25 X 31.28 X .22
61997
61997
26
CORN PAN, 28 X 28 WARMER
61995
61995
27
OLD MAID PAN
41838
41838
28
RUBBER F00T CASE BOTTOM
41282
41282
29
10-24 x 1 1/8 PAN HEAD
47128
47128
30
10-24 SERRATED LOCK NUT
49363
49363
31*
LEAD-IN CORD 20 AMP PLUG
47580
POWER SUPPLY CORD, EXPORT
42369
32
STRAIN RELIEF SR-31-2
41735
41735

Astro Staging Cabinet Model No. 2002, 2002EX
Page 13
gmpopcorn.com
Door Hardware Kits –Individual Component Breakdown
Item
Part Description
Part Number
47054
47055
1
DOOR KNOB
41013
41013
2
8-32 X ½ SCREWS PH PAN W/SEMS
47124
47124
3
ACORN NUT #8-32
47702
47702
4
TEE BOLT
75267
75267
5
MALE HINGE SHORT LEFT
41349
6
FEMALE HINGE LONG LEFT
41352
7
FEMALE HINGE LONG RIGHT
41351
8
MALE HINGE SHORT RIGHT
41350
4
3
8
7
6
5
1
2
3
2
Complete Left Hand Door
Hardware Kit (P/N 47054)
(contains all parts shown above)
Complete Right Hand Door
Hardware Kit (P/N 47055)
(contains all parts shown above)

Astro Staging Cabinet Model No. 2002, 2002EX
Page 14
gmpopcorn.com
Dome Assembly
Item
Part Description
Part No.
All Models
DOME ASSY PLEX SIGN 28IN (complete
assembly includes items shown below)
41345
1
FRONT WRAPPER ASSY. (assembly includes sign
and dome lighting components)
41797
2
SIGN, LIGHTED DOME 28X28
41301
3
BUSHING, SNAP .500 IN
47236
4
LED STRIP COOL WHITE
55379
5
8-32 X 3/8 PH PAN W/SEMS
42227
6
8-32 SERRATED FLANGE NUT
61151
7
LED REFLECTOR, DOME
55535
8
POWER SUPPLY 24VDC 20W
55394
9
MOLDED PLUG
47726
MOLDED RECEPTACLE (not shown)
41712
10
MAIN WRAPPER, 28 X 28
41785
1
2
3
4
5, 6
7
7
8
9
3
10
1
General image shown for parts reference only.

Astro Staging Cabinet Model No. 2002, 2002EX
Page 15
gmpopcorn.com
Wiring Diagram
Model No. 2002

Astro Staging Cabinet Model No. 2002, 2002EX
Page 16
gmpopcorn.com
Model No. 2002EX

Astro Staging Cabinet Model No. 2002, 2002EX
Page 17
gmpopcorn.com
WARRANTY
© 2022 –The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: [phone] Fax: [phone]
[phone] [phone]