Goldmedal Unifloss Top 3034 User manual

© 2019 Gold Medal Products Co. Part No. 13054
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Unifloss Tops
Model Series: 3034 and 3035
Base and Floss Unit sold separately.

Unifloss Top Model Series: 3034 and 3035
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
Floss head rotates at high speeds. Operator MUST keep hands and face
clear of the floss head to avoid injury. Operator must wear eye protection.
Keep all spectators at a reasonable distance, and use a Floss Bubble for
added customer protection.
015_062714
WARNING
Keep all foreign objects out of floss head. To avoid eye injury, DO NOT fill
floss head with sugar while the head is on and rotating.
016_010914
WARNING
Burn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or
servicing. Avoid contact with molten sugar.
006_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914

Unifloss Top Model Series: 3034 and 3035
Page 3
gmpopcorn.com
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is riti al that you all Gold Medal’s
Te hni al Servi e Department at 1-800-543-0862 for any questions about your
ma hine operations, repla ement parts, or any servi e questions. (Gold Medal
Produ ts Co. does not assume any liability for injury due to areless handling and/or
re kless operation of this equipment.) General images may be used in manual for
referen e only.

Unifloss Top Model Series: 3034 and 3035
Page 4
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpa king, he k thoroughly for any damage whi h may have o urred in transit. Claims
should be filed immediately with the transportation ompany. The warranty does not over
damage that o urs in transit, or damage aused by abuse, or onsequential damage due to the
operation of this ma hine, sin e it is beyond our ontrol (referen e warranty in ba k of manual).
Manual
Read and understand the operator’s manual and all other safety instru tions before using this
equipment. To order opies of the operator’s manual go to gmpop orn. om or write to Gold
Medal Produ ts Co., 10700 Medallion Drive, Cin innati, OH 45241 USA 1-(800)-543-0862.
Setup
1. Remove all pa kaging and tape prior to operation.
2. Pla e the unit on a sturdy, level base or ountertop. For Model Series 3035, make sure
the power ord is routed into ountertop or base when installing the unit. (Model
3036 Unifloss Base is available for pur hase separately.)
For Countertop installation ( ountertop to be provided by ustomer) - pla e the unit
over a utout in the ountertop. A shelf (sold separately) is required under the ounter
to set the floss unit on.
3. For 3035 Series Units - Blower vents out the top of unit, allow adequate learan e for
airflow.
4. After the Unifloss Top is in position, tilt the floss ma hine to set it in pla e, then
position the spinner head in the enter of the ut-out. Make sure the shipping bra kets
on the floss ma hine have been removed prior to use (referen e the Instru tion
Manual for the floss unit for omplete installation/setup and operating instru tions
for the floss ma hine).
5. Pla e the aluminum pan over the floss head of the ma hine. Re- enter the floss
ma hine as needed to provide equal spa ing between pan and utout.
6. Referen e the Instru tion Manual for the floss ma hine for ele tri al requirements for
the floss unit.
For 3035 Series Units - Referen e the Ele tri al Requirements se tion of this manual
to plug in the Unifloss Top.
7. After setup, unit should be leaned prior to use (see Care and Cleaning se tion).

Unifloss Top Model Series: 3034 and 3035
Page 5
gmpopcorn.com
Electrical Requirements (Model Series 3035)
The following power supply must be provided (referen e unit Data Plate for Wattage requirement):
3035 Series Units: 120 V~, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A ertified ele tri ian must furnish suffi ient power for proper ma hine operation and install any
supplied re epta le (referen e unit Data Plate for model spe ifi Volts AC, Hertz, and Wattage
requirements). We re ommend this equipment be on a dedi ated and prote ted ir uit. Failure
to wire properly will void the warranty and may result in damage to the ma hine. It is Gold Medal
Produ ts Co.’s re ommendation that this ma hine be plugged dire tly into a wall outlet. The use of
extension ords is not re ommended due to safety on erns, and may ause sa rifi ed and/or
redu ed performan e. Make sure ord is lo ated to prevent a trip hazard or unit upset. Units with
an IEC Power Cord - make sure the IEC ord is properly seated into the IEC re epta le before
powering up the ma hine.
Before You Plug In Machine
1. Make sure all ma hine swit hes are OFF before plugging equipment into re epta le.
2. Make sure wall outlet an a ept the grounded plugs (where appli able) on the power
supply ord.
3. The wall outlet must have the proper polarity. If in doubt, have a ompetent
ele tri ian inspe t the outlet and orre t if ne essary.
4. DO NOT use a grounded to un-grounded re epta le adapter (where appli able).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Unifloss Top Model Series: 3034 and 3035
Page 6
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions (if equipped)
LIGHTS SWITCH
Two position, ON/OFF swit h - supplies power to the exterior display lights and interior
abinet light.
FAN SWITCH
Two position, ON/OFF swit h - supplies power to the exhaust blower.
Operating Instructions
To operate the Unifloss Top, turn the Lights and Fan ON prior to starting the floss unit. After use,
when unit is suffi iently vented, turn swit hes OFF.
Referen e the manual for the floss unit for all floss ma hine instru tions.
Controls View – Mo el Series 3035

Unifloss Top Model Series: 3034 and 3035
Page 7
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet.
Always unplug the equipment before cleaning or servicing.
025_111616
Good sanitation pra ti e demands that all food preparation equipment be leaned regularly (only
use non-toxi , food grade leaners). A lean looking, well-kept ma hine is one of the best ways of
advertising your produ t.
For surfa es needing further leaning or degreasing, Wat hdog Stainless Cleaner (Item No. 2088)
or Wat hdog Con ession Equipment Degreaser (Item No. 2580) is available for use a ordingly.
For any leaning produ ts used, follow the manufa turer’s instru tions on the produ t. DO NOT
use oven cleaners or abrasive materials as they will damage parts of ma hine.
1. Refer to the Floss Unit Manual for instru tions on leaning the floss ma hine.
2. Turn Floss Ma hine and Unifloss OFF, unplug the units and allow them to ool before
attempting to lean.
3. Wipe unit lean using a lean, SLIGHTLY damp loth ( loth may be SLIGHTLY
dampened with soap and water, then wipe again with lean water to remove any
remaining leaner).
4. Clean glass panels with glass leaner. Gold Medal Wat hdog Glass Cleaner (Item No.
2588) is re ommended.
Ammonia leaners will damage plasti doors/panels. Only use a non-ammonia leaner,
su h as Gold Medal Wat hdog Glass Cleaner (Item No. 2588).
Daily Filter Cleaning Instructions (if equipped)
Unifloss is equipped with an effi ient and durable filtration system (for appli able models). The
filter should be leaned ea h day after use.
Steps to Clean Filter
Step 1: Turn unit OFF. Filter is lo ated on the
eiling inside the unit.
Step 2:
Remove filter by sliding it out of the filter
retaining angles.
Step 3: Clean filter in warm soapy water, then
rinse and allow to dry overnight. Reinstall filter
to its original position (referen e image shown).
Filter

Unifloss Top Model Series: 3034 and 3035
Page 8
gmpopcorn.com
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Unifloss Top Model Series: 3034 and 3035
Page 9
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by he king it against the photos, illustrations, and/or
parts list. (General images may be used in manual for referen e only.)
2. Use only approved repla ement parts when servi ing this unit.
3. When ordering, please in lude part number, part name, and quantity needed.
4. Please in lude your model number, serial number, and date of manufa ture (lo ated
on the ma hine nameplate/data plate) with your order.
5. Address all parts orders to Parts Department, Gold Medal Produ ts Co., 10700
Medallion Drive, Cin innati, Ohio 45241-4807
or pla e orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: info@gmpop orn. om
Web Page: gmpop orn. om
Replacing Broken Glass
Broken glass panels an be easily repla ed. Gold Medal Produ ts Co. does not ship glass. It an be
obtained from a lo al glass shop, always pur hase tempered glass.
GLASS DIMENSIONS (Height x Width x Thi kness)
3034 Series: 15 3/16” x 23 1/16” x 1/8”
3035 Series: 28 1/16” x 23 3/16” x 1/8”

Unifloss Top Model Series: 3034 and 3035
Page 10
gmpopcorn.com
3034 and 3034GT Mini Unifloss Top – Parts List
Item Part Description Part Number
3034 3034GT
1 SNEEZE GUARD 13147 13147
2 GLASS RETAIN STRIP FRONT 13154 13154
3 GLASS RETAIN STRIP REAR 13155 13155
4 VINYL GLASS CHANNEL 47132 47132
3034 Mini Unifloss Top
(Base, Floss Ma hine and pan
shown for referen e only, not
in luded with Unifloss Top.)
3036 Base (sold separately, for
parts, see Base Parts List se tion).

Unifloss Top Model Series: 3034 and 3035
Page 11
gmpopcorn.com
3035-00-000 and 3035-00-001 Unifloss Top – Parts List
Item Part Description
Part Number
3035-00-000
3035-00-001
1 FAN BLADE 13009
2 MOTOR FAN 13010
3 ALUMINUM MESH FILTER 13013
4 ANIMATED SIGN FACE 13075
5 DISC ANMTD SIGN 13076
6 MOTOR,110V-60CY (for sign) 13077
7 DECAL FRONT GLASS 13087
8 ON OFF SWITCH LABEL (for light) 13369
9 ON OFF SWITCH LABEL (for fan) 13370
10* POWER SUPPLY CORD 15 AMP 22038
11 STRAIN RELIEF SR-6P3-4 76026
12 SWITCH, TOGGLE SPST 47201
13 GLASS RETAINER REAR 47592
14 GLASS RETAINER FRONT 47593
15 GLASS CHAN 22 7/8 47694
16 GLASS CHAN 27 13/16 47697
17 LED STRIP COOL WHITE (for sign) 55379
18 POWER SUPPLY 24VDC 60W 55586
19 LED LIGHT 800 LUMENS ( abinet light) 55590
*CAUTION: If supply cor is amage , it must be replace
by Gol Me al Pro ucts Co., its service agent, or similarly
qualifie persons in or er to avoi a hazar .
Mo el 3035-01-000 - Front Counter unit shown for general reference.
3035-00-
000

Unifloss Top Model Series: 3034 and 3035
Page 12
gmpopcorn.com
3036 Base – Parts List
Item Part Description Part Number
3036
1 SWIVEL CASTER W/O LOCK 37513
2 NSF SWIVEL CSTR W/LOCK 37514
3 5/16-18 X 5/8 PH TR M/S (Caster fastener) 46638
4 WASHER 5/16 INT TOOTH (Caster fastener) 74137
5 5/16-18 SERRATED LOCK NUT (Caster fastener) 49317

Unifloss Top Model Series: 3034 and 3035
Page 13
gmpopcorn.com
Wiring Diagram
Model No. 3035-00-000 and 3035-00-001

Unifloss Top Model Series: 3034 and 3035
Page 14
gmpopcorn.com
WARRANTY
© 2019 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: [phone] Fax: [phone]
[phone] [phone]