Goldmedal 2114 User manual

Accu-Meter Oil Pump
Instruction Manual
Model #2114
Cincinnati, OH 45241-4807 USA
Part No. 79064
Revised June 1996

SAFETY PRECAUTIONS

INSTALLATION
CHECKING SHIPMENT
Your new Accu-Meter Oil Pump is completely assembled and ready to operate. Remove the
corrugated carton from the machine. Check thoroughly for any damage which may have occurred
in transit. Damage claims should be filed immediately with the transportation company.
ELECTRICAL REQUIREMENTS
Standard units operate on 120 Volt, 60 Hertz, 7.05 Amps.
FINAL PREPARATIONS
Your new Accu-Meter Oil Pump was adjusted, inspected and tested before it left the factory, and is ready
to operate with some fine adjustment to the volume of oil delivered to your popper (see adjustment
instructions on the following page). NOTE: We recommend premelting oil in the bucket with Gold
Medal’s HOT WAND, catalog #2018, before inserting your new bucket pump to prevent the possibility of
damage to the heat element.
INSTALLATION
1. Place your oil pump in a premelted bucket of oil.
2. Connect the plastic oil delivery tube (located in your popper) to the quick disconnect (located on your oil
pump) using the hose clamp supplied with your popcorn machine.
3. Connect the power supply cord (located under your popper) to the disconnect plug on your oil
pump. NOTE: Volume measurements should be taken from the oil delivery tube located in your
existing popper above the kettle.
Accu-Meter Oil Pump
1
M ODEL #2114

OPERATING INSTUCTIONS
HIGH HEAT
1. Turn on the “OIL SYSTEM MASTER SWITCH” located on the switch panel in your popper. 2. The
High Heat Cycle is factory set at 30 minutes.
3. If desired, reset the High Heat Timer to your desired cycle time by turning the control with a small
screwdriver.
4. To start the High Heat Cycle, press the "HEAT" button.
PUMP CYCLE
1. The oil quantity is factory set at approximately 8 ounces (237 ml). You will need to set the
volume of oil to your corn charge.
2. With a measuring cup under the tube in the ceiling of the popper over the kettle, set the quantity to
your desired ratio (30%). See chart below.
3. Allow oil to drain completely before rechecking oil quantity.
Raw Corn Charge Oil Charge
12 Oz. (355 ml) 3½ Oz. (103 ml)
14 Oz. (414 ml) 4¼ Oz. (126 ml)
16 Oz. (473 ml) 4¾ Oz. (140 ml)
20 Oz. (591 ml) 6 Oz. (177 ml)
28 Oz. (828 ml) 8½ Oz. (251 ml)
32 Oz. (946 ml) 9½ Oz. (281 ml)
36 Oz. (1065 ml) 10¾ Oz. (318 ml)
Accu-Meter Oil Pump
2
M ODEL #2114

MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN
TENDEDONLYFOR QUALIFIEDSERVICEPERSONNELWHO
AREFAMILIARWITHELECTRICAL EQUIPMENT.THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this equip
ment to prevent the possibility of injury.
ORDERING SPARE PARTS
1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity desired.
3. Please include your model name and machine serial number (located on the machine
nameplate) with your order. 4.
Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [e-mail]
Accu-Meter Oil Pump
3
M ODEL #2114

BUCKET SEASONING PUMP ASSEMBLY
Accu-Meter Oil Pump
4
M ODEL #2114

PARTS LIST – BUCKET SEASONING PUMP ASSEMBLY
Item No. Part No. Description
1 79063 Junction Box
79062
Junction Box Cover
2
79075
Mounting Clip
3 79004 Disconnect Plug
4
41033
Pilot Light
5
79086
Heat Sink Assembly
6
79078
Dual Timer Bucket Pump
7
41031
Switch, Oil Pump
8
79006
Pump Motor
9
79022
Pipe Reducer
10
79008
Quick Disconnect Coupling
11
79005
Pump Motor Gasket
12
79015
Oil Delivery Tube
13 79030 Bucket Pump Lid Assembly
14
79002
Heat Element
15
10094
Spring, U
-
Clip
16
79019
Drive Shaft Bushing (Motor End)
17
79011
Drive Shaft
18 79020 Drive Shaft Bushing (Pump End)
19
79001
Pump Assembly
20
79018
Clamp, Filter Screen
21
79017
Element Retainer
22 79016 Filter Screen
23 79023 Pump Mounting Tube
Accu-Meter Oil Pump
5
M ODEL #2114

ELECTRICAL SCHEMATIC
Accu-Meter Oil Pump
6
M ODEL #2114

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be
free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP-
TION ON THE FACE HEREOF. We neither assume, nor authorize any other person to
assume for us, any other obligation or liability in connection with the sale of said GOLD
MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP-
MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING
THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY 10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA