Goldmedal Shav-A-Doo 1203 User manual

© 2022 Gold Medal Products Co.
Part No. 69006
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Shav-A-Doo
Model Series: 1203

Shav-A-Doo Model Series: 1203
Page 2
gmpopcorn.com
Table of Contents
SAFETY PRECAUTIONS ...................................................................................................................................3
INSTALLATION INSTRUCTIONS ...................................................................................................................5
Inspection of Shipment .......................................................................................................................................5
Manual.......................................................................................................................................................................5
Model Description.................................................................................................................................................5
Items Included with this Unit ...........................................................................................................................5
Setup...........................................................................................................................................................................5
Electrical Requirements .....................................................................................................................................6
Before You Plug In Machine ..............................................................................................................................6
OPERATING INSTRUCTIONS .........................................................................................................................7
Controls and Their Functions...........................................................................................................................7
Ice Requirements ..................................................................................................................................................7
Operating Instructions ........................................................................................................................................7
Care and Cleaning .......................................................................................................................................8
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY ...............9
MAINTENANCE INSTRUCTIONS ...................................................................................................................9
Installing New Shaver Blades............................................................................................................... 10
Blade Replacement ............................................................................................................................................10
Set Blade Height............................................................................................................................................11
ORDERING SPARE PARTS............................................................................................................................12
Replacing Broken Glass....................................................................................................................................12
Cabinet View ........................................................................................................................................................13
Shaver Head and Accessories ........................................................................................................................14
Wiring Diagram ........................................................................................................................................15
WARRANTY...................................................................................................................................................... 17

Shav-A-Doo Model Series: 1203
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
This machinery contains sharp blades. Keep hands and body parts clear
at all times.
037_103114
WARNING
NEVER put your fingers into the shaver body (the goose-neck, ice chute, or
hopper). Serious injury may occur.
017_103114
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514

Shav-A-Doo Model Series: 1203
Page 4
gmpopcorn.com
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
DO NOT install equipment in an area where a water jet is used.
Unit to be installed in locations where ambient temperatures are between a minimum of
5°C (41°F) and a maximum of 55°C (131°F).
Unit to be installed in locations where it can be overseen by trained personnel.
Install unit on a level surface.
Unit is for shaved ice.
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

Shav-A-Doo Model Series: 1203
Page 5
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
1203 Series Shav-A-Doo Ice Shaver.
Items Included with this Unit
•Plastic Snow Dipper (PN 1088)
•Ice Scoop (PN 39068)
•Drain Hose (PN 12159, order by the foot)
•Manual and Registration/Warranty Card
Setup
1. Remove all packing material and tape before starting operation.
2. Place unit on a sturdy, level base which can withstand accidental dripping of water
and ice.
3. Set drain pan (with hose fitting) in unit—position fitting in unit opening, see image.
4. Push drain hose onto the barbed drain fitting. Drain hose funnels excess water to floor
drain or basin tub. When in use, ensure the hose is positioned so water drains
appropriately. Drained water is not intended for human consumption.
5. Unit should be cleaned prior to use (see Care and Cleaning section).
Drain fitting routes
through cabinet opening.
Push drain hose onto
barbed fitting.

Shav-A-Doo Model Series: 1203
Page 6
gmpopcorn.com
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
1203-00-000: 120 V~, 60 Hz
1203-01-000: 220-230 V~, 50/60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power
supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Shav-A-Doo Model Series: 1203
Page 7
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
POWER SWITCH
Lighted Rocker Switch –supplies power to the momentary button switch.
MOMENTARY SWITCH
Momentary Switch must be engaged for unit to operate. Press switch to operate/energize
the shaver motor; release the switch to de-energize the motor.
ICE HOPPER/PUSHER HANDLE
The hopper holds ice and funnels it to the shaver blades. Pusher Handle presses ice into
the shaver blades.
Ice Requirements
The shaver accepts ice cubes or block ice (if broken into pieces approximately 2 to 3 inches in
size). The ice will not enter the shaving chute if the pieces are too large.
Note: Harder ice will result in finer snow; soft ice will result in coarser snow. Softened ice
makes better snow and prolongs blade life.
Operating Instructions
1. Raise hopper handle (pusher) and load hopper with ice cubes (approx. 1” from top).
2. Close pusher handle.
3. Turn the power switch ON.
4. Apply gentle downward pressure on the hopper handle and press the momentary
switch until all ice in hopper has been shaved, then release the button.
Practice helps you gauge when to stop and allow the ice to resettle against the shaver
head. Applying too much pressure results in coarse snow; too little pressure can make
snow mushy.
5. DO NOT lift the pusher until the motor is off and the shaver head has stopped.
Note: Never allow any foreign or metallic objects around the shaver area. Ice picks,
scoops, and debris that may be in the ice often damage blades.
Power
Switch
Pusher Handle
Momentary
Switch
Ice Hopper

Shav-A-Doo Model Series: 1203
Page 8
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet or steam
cleaner. Always unplug the equipment before cleaning or servicing. 025_051321
WARNING
This machinery contains sharp blades. Keep hands and body parts clear
at all times.
037_103114
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners).
Follow the directions below to clean and sanitize the unit each day after use.
1. With the machine OFF, unplug the unit before attempting to clean.
2. Empty water from pans and clean using appropriate cleaners for the type of machine;
review all manufacturer’s instructions and warnings on cleaning product prior to use.
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
DO NOT use Ammonia cleaners, they will damage plastic panels.

Shav-A-Doo Model Series: 1203
Page 9
gmpopcorn.com
THE FOLLOWING SECTIONS ARE FOR QUALIFIED SERVICE PERSONNEL ONLY
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle. Keep cord and plug off the ground and away
from moisture. Always unplug the equipment before cleaning or servicing.
DO NOT immerse any part of this equipment in water.
DO NOT use a water jet or excessive water when cleaning. 008_012221
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Shav-A-Doo Model Series: 1203
Page 10
gmpopcorn.com
Installing New Shaver Blades
WARNING
This machinery contains sharp blades. Keep hands and body parts clear
at all times.
037_103114
The section describes the procedure to replace the shaver blades. ALWAYS turn the machine OFF
and unplug unit from the power supply prior to blade inspection or replacement. Use a flashlight
to examine the blades in the shaver body. If the blades appear to be nicked or bent, then the
blades should be replaced.
Blade Replacement
1. With the machine OFF, unplug the unit from the power supply.
2. Remove motor cover (keep all fasteners as they will be used to reinstall the cover).
3. Use a permanent marker and put a guide mark on the motor shaft where the
shaver head stops; also place a small guide mark on the cabinet where the motor
sets (reference shaver cut away view on next page).
4. To remove the shaver head from the motor shaft, loosen the motor mounting
bolts. (If unit has a hopper support and guide, it must also be removed).
5. Pull motor back until the (2) Allen head set screws on the shaver head are visible.
Loosen the (2) set screws (do not remove set screws).
6. Carefully guide the shaver head off of the motor shaft and through the hopper. If
the shaver head is frozen to the shaft, pull the motor back trapping the shaver
head against the inside of the hopper, until the shaver head disengages.
7. After removing the shaver head, check the motor shaft for burrs and corrosion
(use a fine tooth file to remove any burrs or corrosion).
8. Remove blades from shaver head. Replace old blades with a new set (blades may
be re-sharpened).
9. Position new blades on shaver head and insert blade mounting screws until finger tight.
10. Set the blade thickness to 1/32” (0.8 mm) using a height gauge (thickness of a
dime), reference Set Blade Height illustration shown on next page. Make sure the
blade height is even across the shaver head.
11. Tighten the blade mounting screws completely. Check the blade height again to
ensure the blades did not move while tightening the screws.
12. Carefully guide the shaver head through the hopper and back onto the motor
shaft; realign head with guide mark made on the shaft in Step 3 above. (The
pusher handle may be used to help press the shaver head onto the shaft.)
13. The shaver head set screws must be on the flat side of the motor shaft. Once
aligned, fasten set screws securely.

Shav-A-Doo Model Series: 1203
Page 11
gmpopcorn.com
14. Adjust the motor to realign with guide mark made on the cabinet in Step 3, then
refasten motor mounting bolts (if unit has a hopper support and guide, it must
also be reinstalled). Check the shaver head to make sure it is not rubbing against
the back of the hopper and the blades are not touching the pusher handle or sides
of hopper; adjust as needed.
NOTE: Replace any shims that were between the motor base and the mounting surface.
15. Reinstall motor cover.
With a permanent marker, mark
shaft where shaver head stops.
Shaver Head
(2) Set Screws (fasten on
flat side of motor shaft)
With a permanent marker, mark
cabinet where motor sets.
Motor
Mounting
Bolts
Height Gauge 1/32” (0.8 mm)
(thickness of a dime)
Set top of blade flush with
height gauge, as shown.
Blade Mounting Screw
Shaver Blade
Shaver Head
Cut Away View of Shaver Head on Motor Shaft
General shaver image shown for reference only (models may vary).
Set Blade Height

Shav-A-Doo Model Series: 1203
Page 12
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to Parts Department, Gold Medal Products Co., 10700
Medallion Drive, Cincinnati, Ohio 45241-4807
or place orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: [email protected]
Web Page: gmpopcorn.com
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop, always purchase tempered glass.
GLASS DIMENSIONS (Height x Width x Thickness)
Front Glass: 13.354” x 15.6” x 1/8” (1 Piece)
Side Glass: 13.354” x 11.989” x 1/8” (2 Pieces)

Shav-A-Doo Model Series: 1203
Page 13
gmpopcorn.com
Cabinet View
Item
Part Description
Part Number
1203-00-000
1203-01-000
26
1/4 HP MOTOR
55448
113002
27*
POWER SUPPLY CORD
22038
42369
28
WARNING LABEL CORD
68720
68720
23
24
Rubber
Foot
*CAUTION: If supply cord is damaged, it must
be replaced by Gold Medal Products Co., its
service agent, or similarly qualified persons
in order to avoid a hazard.
For Glass Panels, see
Replacing Glass section.
10
7
4, 5
1
8
6
11
9
2
3
Strain
Relief
For Power Cord,
see table below.
13, 14
12
22
21
18, 19, 20
17
15, 16
Plastic Sno Pan
(w/drain fitting)
Door
Panel
27*, 28
Power Cord,
Cord Label
26
Shaver
Motor
Item
Part Description
Part Number
All Models
Item
Part Description
Part Number
All Models
1
PUSHER HANDLE (replacement)
22068
2
HOPPER CASTING
22009
3
WARNING LABEL
44018
4
5/16-18 X 2 PH PAN HD M/S
12059
5
5/16-18 SERRATED LOCK NUT
49317
6
MOTOR COVER SNO KONE BLUE
61111B
7
OPERATON WARNING LABEL
44019
8
GUARD WARNING LABEL
44027
9
SWITCH LABEL
13141
10
MOMENTARY SWITCH
38971
11
SWITCH, DPST LIT ROCKER
42798
12
STRAIN RELIEF SR-6P3-4
76026
13
MALE HINGE SHORT LEFT
41349
14
LH FEMALE STEEL HINGE
61359
15
8-32 X 3/8 PH PAN W/SEMS
42227
16
ACORN NUT #8-32
47702
17
LABEL, DO NOT CLEAN......
49393
18
KNOB 8-32
47120
19
8-32X1/2 FL HD PH MS
20066
20
MAGNET USES 8 FLT HD SC
50013
21
DOOR
23235
22
SNO PAN PLASTIC
22701
23
8-32 SERRATED FLANGE NUT
61151
24
RUBBER BUMPER/FOOT
87247
25
DECAL SNO-KONE
12538
25

Shav-A-Doo Model Series: 1203
Page 14
gmpopcorn.com
Shaver Head and Accessories
Item
Part Description
Part Number
1
SHAVER HEAD
22015
2
1/4-20 X 3/8 SET SC
69703
3
2 HOLE BLADE REPLACE SET (includes 2 blades,
washers, and screws)
22017
4
DRAIN HOSE 3/4 ID 7/8 OD (sold by the foot)
12159
5
PLASTIC SNOW DIPPER
1088
6
ICE SCOOP
39068
2
5
6
3
1
4

Shav-A-Doo Model Series: 1203
Page 15
gmpopcorn.com
Wiring Diagram
Model 1203-00-000

Shav-A-Doo Model Series: 1203
Page 16
gmpopcorn.com
Model 1203-01-000

Shav-A-Doo Model Series: 1203
Page 17
gmpopcorn.com
WARRANTY
© 2022 –The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: [phone] Fax: [phone]
[phone] [phone]