Goldmedal Deluxe 60 Special 2660 User manual

© 2016 Gold Medal Products Co. Part No. 49217
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Kingery
®
/
Deluxe
60 Special
Poppers
Model No. 1871, 2660, 2660A, 2660ST
Model
1871
Models 2660, 2660A

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 2
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at -800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 4
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 0700 Medallion Drive, Cincinnati, OH 4524 USA -(800)-543-0862.
Model Description
1871: Kingery 6 oz. Popper, unit has a bronze dome and frame, and etched glass.
2660: Deluxe Sixty Special 6 oz. Popper, unit has a red dome.
2660A: Deluxe Sixty Special 6 oz. Popper, unit has a red dome and is equipped with a
PowerOff
TM
Control feature.
2660ST: Deluxe Sixty Special 6 oz. Popper, unit has a stainless steel dome.
Items Included with this Unit
Aluminum Scoop
Measure 6.5 cc
Measure 6 oz.
lack Crutch Tips
ulb for Cabinet
Interior
Knobs with Tee olts
(for Popper Doors)
Knob with Screw
(for Old Maid Pan)

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 5
gmpopcorn.com
Setup
This unit has been tested at the factory.
. Remove all packaging and tape prior to operation.
2. Place the unit on a sturdy, level base.
3. The popper unit has 4 glide feet preinstalled at the factory (see image below). Install a
Black Crutch Tip on each of the 4 glide feet. Firmly push the crutch tip over the glide
until it covers the glide entirely.
4. Door knobs are shipped in the accessories pack located inside the machine. Install a
door knob with tee bolt on each popper door; install the knob with screw on the old
maid pan.
5. Carefully install the light bulb (do not over-tighten) into the lamp holder located in the
cabinet interior. Ensure the unit is OFF and unplugged before installing or changing
the bulb (reference the Electrical Requirements section).
6. Make sure kettle lead-in cord is securely plugged into unit, and twisted to lock into the
kettle receptacle.
lack Crutch Tip
Glide
(pre
-
installed
at the factory)
General image shown for reference only.

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 6
gmpopcorn.com
Electrical Requirements
The following power supply must be provided:
1871, 2660, 2660A, 2660ST: 20 V~, 220 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 7
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
KETTLE HEAT SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the
popping kettle. The green switch light ON indicates there is power to the kettle heating
element.
KETTLE MOTOR SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor.
The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or un-
popped) in the kettle. The green switch light ON indicates there is power to the agitator
motor.
LIGHTS/WARMER SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the interior cabinet light
and heat element for the corn pan.
POWEROFF CONTROL
The PowerOff Control feature will automatically turn the kettle heat off after 5 minutes
of idle time (no popcorn popped). The PowerOff Control will prevent the heat element and
thermostat from cycling OFF-ON if the Kettle Heat Switch is left on. This feature saves
electrical power and extends the life of the kettle heating element and thermostat.
•When the Kettle Heat Switch is turned ON, and the kettle thermostat switches OFF,
the PowerOff Control’s 5 minute timer starts; the 5 minute timer resets each
time a batch of popcorn is popped.
•The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate
the kettle has been automatically turned OFF.
•To restart the kettle heating, cycle the Kettle Heat Switch OFF-ON.
Kettle Heat Switch
Kettle Motor Switch
Label used on units with the
PowerOff Control feature.
Lights/Warmer
Switch

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 8
gmpopcorn.com
Popping Corn
This section describes instructions for popping Standard (salted popcorn).
Amount of Popcorn and Oil
The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored
coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in
your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Ingredient amounts for popping Standard Popcorn:
Kettle Size
Popcorn Charge
Oil Charge
Flavacol (Salt)
6 oz.
6 oz. ( 77 ml)
2 oz. (59 ml)
/2 Tblsp. (7.5cc)
For best results use Mega-Pop® 6 oz. premeasured pouches (Item# 2836).
Popping Standard (Salted) Popcorn
. Turn the Lights/Warmer, Kettle Heat and Kettle Motor Switches ON.
2. To determine when the kettle is ready to pop corn (about 4 minutes), test pop three
kernels of corn and one ounce (30 ml) of popping oil. When the kernels pop, the kettle
is ready for use.
3. Lift the kettle lid and load the Mega-Pop® premeasured popcorn and oil pouch into
kettle, or pour in the popcorn and Flavacol, then add oil in the premeasured amounts
specified above. Close lid.
4. When the corn has finished popping, gently dump the popcorn.
5. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced
open by the popping corn. This procedure saves electricity, since the kettle has plenty
of heat, and helps eliminate smoke/odor from any oil residue that remains after
popping has stopped.
6. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are
turned OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!
If unit is equipped with the PowerOff Control feature, the unit will automatically shut
kettle heat OFF after 5 minutes of idle time (no popcorn popped). To restart kettle
heating, cycle the Heat Switch OFF-ON.

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 9
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
025_020314
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
028_082715
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Note: It is extremely important to follow all of the cleaning procedures, otherwise parts
damage and equipment failure will result. The warranty does not cover parts that
are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool
at least hour before attempting to clean. DO NOT use ice or water to cool
down a hot kettle! Severe kettle damage will result!
. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven
cleaners or abrasive materials as they will damage the kettle.
2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons
per gallon of water. It is not necessary to use the entire gallon at once; only use
enough to fill the kettle /2 inch deep.
3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.
4. Allow to cool for at least hour, then dump the solution into a bucket and wipe the
inside of the kettle with a clean cloth. Make sure all of the solution goes into the
bucket; do not spill any in the interior of the machine.
For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution
into a bucket and wipe the inside of the kettle with a clean cloth.
5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp
cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result.

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 10
gmpopcorn.com
Daily Unit Cleaning Instructions
. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Make sure to clean all pans/accessories in order to sanitize them before each use.
3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet.
4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item
No. 2588) is recommended.
Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 11
gmpopcorn.com
Troubleshooting
Issue
Possible Cause
Solution
Power to the Unit
A.
Power to
the
Unit
A.
Make sure the
unit’s power
cord is plugged in.
Kettle Does Not Heat
A.
Power to the Kettle
A.
Make sure kettle lead
-
in cord is plugged in and
twisted to lock into the kettle receptacle.
B.
Kettle Heat Switch
B.
Have a qualified service person c
heck the
voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.
C.
PowerOff Control
C.
Units with the PowerOff
Control feature, kettle
heat will automatically shut OFF after 5
minutes of idle time (no popcorn popped).
The small green neon light in the Kettle Heat
Switch will blink OFF-ON to indicate the kettle
has been automatically turned OFF.
To restart kettle heating, cycle the Heat Switch
OFF-ON. Reference the Controls and Their
Functions section of this manual.
D.
Heating Element
D.
Heating element in the kettle may
be burned
out. Check with a qualified service person for
inspection/repair.
Long Popping Cycles
(Longer than 4 minutes for
Salt Popcorn)
A.
Low Voltage
A.
If the machine is operated on low voltage, this
could cause the kettle not to reach the proper
operating temperature. Check with a qualified
electrician.
B.
Inadequate Supply Lines
B.
Inadequately sized electrical supply lines
or
use of extension cord, in addition to being a
fire hazard, would also prevent the kettle from
reaching the proper operating temperature.
Check with a qualified electrician.
C.
Inferior Corn
C.
Inferior quality cor
n would result in longer
popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even then,
if you let your corn pick up moisture or dry
out, your popping cycles will be slow.
Kettle Agitator Shaft not
Rotating
A.
Kettle Motor Switch
A.
If the kettle agitator shaft is not rotating,
DO NOT pop corn. Make sure the Kettle Motor
Switch is ON. If the switch is ON, and the shaft
is not rotating, the switch or motor may be
faulty, contact qualified service personnel for
inspection/repair.
B.
Kettle Agitator
S
haft
/Stir
Blade not rotating. (Unit
must be OFF, unplugged
and cool prior to
checking or adjusting
the agitator assembly.)
B.
If the kettle agitator shaft is not rotating,
DO NOT pop corn. Check the clearance
between the kettle bottom and the stir blade;
it should be /32” (use a dime). To adjust,
reference the Agitator Set Collar Adjustment
section.

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 12
gmpopcorn.com
Agitator Set Collar Adjustment
The following instructions describe how to properly adjust set collars on an agitator assembly
with a floating stir rod.
Step 1:
Make sure machine is OFF and
unplugged, then allow unit to cool completely
before attempting to adjust the agitator height.
Step 2: Loosen the set screw in each set collar
to be adjusted.
Step 3: With the kettle mounted in the popper,
adjust the shaft so the Agitator’s Spur Gear
contacts half of the Drive Motor Spur Gear
(reference Spur Gear Placement image at right).
DO NOT set spur gears at full gear contact; it
can cause binding as the kettle is dumped.
Step 4: Once shaft is positioned correctly,
re-tighten the set screw in the set collar above
the crossbar to secure in place.
Step 5: Adjust clearance between the bottom of
the crossbar and the lower set collar to /32”
(thickness of a dime); then re-tighten set screw
to secure in place (see image below).
Step 6: Adjust set collar for agitator weight to
be between 3/ 6” to /4” above the agitator
weight. Once adjusted, re-tighten set screw to
secure in place.
Drive Motor
Spur Gear
Agitator’s Spur Gear
Agitator’s Spur Gear
should set halfway
up on Drive Motor
Spur Gear.
Set Collar
w/Set screw
Agitator shown for general image
reference only (lids not shown for
clarity).
Adjust clearance to
thickness of a dime.
3/16” to 1/4” max.
Spur Gear Placement
Steps to Adjust Set Collars
Set Collar above Crossbar
Lower Set Collar
(below Crossbar)
Set Collar
(for Agitator Weight)
Agitator Weight
Stir Rod
Crossbar

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 13
gmpopcorn.com
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 14
gmpopcorn.com
ORDERING SPARE PARTS
. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
0700 Medallion Drive
Cincinnati, Ohio 4524 -4807
Or, place orders by phone or online:
Phone: [phone]
(5 3) 769-7676
Fax: [phone]
(5 3) 769-8500
E-mail: [e-mail]
Web Page: gmpopcorn.com

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 15
gmpopcorn.com
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop, always purchase tempered glass.
GLASS DIMENSIONS (Height x Width x Thickness)
Front Glass: 22 /2” X 5 /8” X /8” ( Piece)
Side Glass: 22 /2” X 3” X /8” (2 Pieces)
. With the machine OFF, unplug the unit and allow it to cool before attempting to
replace any glass.
2. Carefully remove all loose pieces of broken glass.
3. Lift out the Corn Pan (see Figure A).
4. Locate the Glass Retainer Strips holding in the glass panel, remove the screws to unfasten
the retainers (see Figure A). Carefully remove the rest of the broken glass. Remove all
rigid glass channels from around the glass to be replaced, set channels aside for reuse.
To remove the Glass Strip with the Cover:
•Bend out the tabs at the bottom and top of Glass Strip (see Figure A).
•Pinch in the edge of the Glass Strip Cover just enough to rotate the cover out of the
Glass Strip, then remove (see Figure B).
•Remove the Glass Strip. When reinstalling, ensure the wiring is on top of the Glass
Strip (as seen in Figure C).
5. Apply decals (if desired) to the new glass panel.
6. Slide the rigid glass channels over the exposed sides and bottom of the new glass panel.
7. Fasten new glass panel in machine with the existing Glass Strips and screws using the
steps above as reference.
Figure A
Figure
Figure
C
Rotate
Cover out
to remove.
Wiring is on top
of Glass Strip.
Remove Glass
Strip to remove
glass panel.
C
orn Pan
(lift off to remove)
Glass Retainer Strip
(remove screws to unfasten)
Glass Strip
(bend tab out to
remove cover)
Glass Strip Cover

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 16
gmpopcorn.com
Kettle Assembly – 56000 – Parts Breakdown
3
4
5 6
10 11
17
17
18, 16
Element/Heater View
19 20
Complete Kettle ottom Assembly i
ncludes
Kettle Shell and Kettle Lead Assembly
25
24
23
22
21
26 27
9
13
14
15*
16
*See Parts
List note.
Co
mplete Agitator Assembly
(Includes Lids)
Complete Agitator Assembly
(Includes Lids)
1
2
Kettle Model 56000 s
hown
56000 Shown
7
5
1
10
**Apply Loctite 246 to bottom
of set screws before installing.
8**

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 17
gmpopcorn.com
Kettle Assembly – 56000 – Parts List
Item Part Description Part Number
56000
8
-
32 TALL ACORN NUT
47702
2
8
-
32 X /2 PHIL PAN M/S
47 4
3
KETTLE SHELL
4943
4
KETTLE LEAD ASSY
49328
5
DUMP HANDLE RH
493 4
6
DUMP HANDLE KNOB
47 0
7
SPACER (f
or Dump Handle)
49362
8
8
-
32 X ” SET SCREW
77933
9
LID & AGITATOR ASSY
(Complete Assembly)
59 03
0
KETTLE CROSSBAR ASSEMBLY
59 02
FRONT LID W/FORMED LIFTER
490 7
2
REAR KETTLE LID
490 6
3
AGITATOR BEARING HUB
43434
4
NEEDLE BEARING
47 06
5*
SPUR GEAR
KIT (Includes 2 gears with set
screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)
47059K
6
SET SCREW # 0
-
32 X 3/ 6
4 742
7
AGITATOR SHAFT
697 0
8
SET COLLAR 5/ 6 ID 5/8 OD
46649
9
AGITATOR WEIGHT
697 5
20
STIR ROD
697 4
Kettle ottom Assembly
–
Element
/Heater
View
2
KETTLE BOTTOM ASSEMBLY (Complete
Assembly - includes Kettle Shell, Kettle Lead
Assembly and parts listed below)
56000W
22
KETTLE GASKET
49368
23
KETTLE/HEATER
56006
24
8
-
32 TOP LOCK NUT (where used, always replace
lock nut if removed) 67943
25
450°F THERMOSTAT
(includes two 6-32 X 3/ 6 Screws) 76089
26
THERMOSTAT SHUNT BAR
47 93
27
525
°F THERMOSTAT
(includes two 6-32 X 3/ 6 Screws) 76702

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 18
gmpopcorn.com
Cabinet Exterior – Front View
Item Part Description Part Number
1871
2660
2660A
2660ST
FRONT GLASS DECAL
49 58
49 58
49 58
2
DOME
49583
49456
49456
4958
3
2
2
/8” GLASS CHANNEL (used on side edges of
front and side glass panels) 492 2 492 2 492 2 492 2
4
3 /8
” GLASS CHANNEL (used on bottom edge
of side glass panels) 492 3 492 3 492 3 492 3
5
5 /8
” GLASS CHANNEL (used on bottom edge
of front glass panels) 492 4 492 4 492 4 492 4
6
GLIDE
47328
47328
47328
47328
7
0
-
24 X 3/4 HEX HD
4 3 4
4 3 4
4 3 4
4 3 4
8
BLACK CRUTCH TIP
49 23
49 23
49 23
49 23
2
1
6, 7
8
See Kettle
Assembly
Section
Model
2660
shown
3
For Glass Panels,
see Replacing
Glass section.
4, 5

Kingery/Deluxe 60 Special
Poppers Model No. 1871, 2660, 2660A, 2660ST
Page 19
gmpopcorn.com
Cabinet Exterior – Rear View
Item Part Description Part Number
All Models
MAGNETIC BRACKET SHIM
38527
2
MAGNETIC CATCH BRACKET
77089
3
MAGNETIC CATCH
4756
4
**
COMPLETE DOOR HARDWARE KIT
6 380
5
PLEXIGLASS DOOR
49396
6
DROP PANEL
492 0
7
KNOB LID LIFT
47 20
8
8
-
32” X 3/8” PH PAN W/SEMS
42227
9
OLD MAID PAN
49 00
0
#SR
-
6P3
-
4 STRAIN RELIEF
76026
LEAD
-
IN CORD 5 AMP PLUG
22038
Model
2660
shown
**
Complete
Door
Hardware Kit
(See next page for individual
component breakdown).
4**
5
6
7, 8
9
10
For Labels, see
Safety Label
Section.
11*
*
CAUTION: If supply cord is damaged, it must
be replaced by Gold Medal Products Co., its
service agent, or similarly qualified persons
in order to avoid a hazard.
2, 3 1
4**